Pioneer GEX-P910XM User manual

INSTALLATION MANUAL

GEX-P910XM

Printed in Thailand

<CRB1802-A/N> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck, or bus, check the battery

voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the ≠battery cable before beginning

installation.

• Refer to the owner’s manual for details on

connecting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and

seat rails. Do not route wiring in places that get

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same

colors correctly.

This product conforms to CEMA cord colors.

• Cords for this product and those for other products

may be different colors even if they have the same

function. When connecting this product to another

product, refer to the supplied Installation manuals

of both products and connect cords that have the

same function.

Connecting the Units

Connection Diagram

Fig. 1

Head Unit

(sold separately)

IP-BUS cable

To IP-BUS Input

(Blue)

Yellow

To terminal always supplied with power

regardless of ignition switch position.

Black (ground)

To vehicle (metal) body.

Fuse holder

IP-BUS Output

(Black)

This Unit

Antenna Input

Power Supply

Antenna Unit

(AN-91XM)

(sold separately)

IP-BUS Input

(Blue)

Multi-CD player

(sold separately)

Green

(Terrestrial)

Yellow (Satellite)

Black

(19 ft. 8 in.)

Protect the Antenna Connector

Fig. 2

Screw (3 ×6 mm)

Installation

Note:

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected

up properly, and the unit and the system work

properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

of the vehicle.

• Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• When mounting this unit, make sure none of the

leads are trapped between this unit and the sur-

rounding metalwork or fittings.

• Do not mount this unit near the heater outlet,

where it would be affected by heat, or near the

doors, where rainwater might splash onto it.

• Before drilling any mounting holes always check

behind where you want to drill the holes. Do not

drill into the gas line, brake line, electrical wiring

or other important parts.

• If this unit is installed in the passenger compart-

ment, anchor it securely so it does not break free

while the car is moving, and cause injury or an

accident.

• If this unit is installed under a front seat, make sure

it does not obstruct seat movement. Route all leads

and cords carefully around the sliding mechanism

so they do not get caught or pinched in the mecha-

nism and cause a short circuit.

Installing the Unit

Mounting with Brackets (Fig. 3)

Fig. 3

Screw (4 ×6 mm)

Car mat or chassis Bracket

Tapping screw (4 ×12 mm)

Drill 2 to 2.5 mm diameter holes.

Table of contents

Other Pioneer Tuner manuals

Pioneer

Pioneer F-208RDS User manual

Pioneer

Pioneer TX-130L Series User manual

Pioneer

Pioneer SH-D09 User manual

Pioneer

Pioneer TX-D1000 User manual

Pioneer

Pioneer F-225L User manual

Pioneer

Pioneer GEX-FM903XM User manual

Pioneer

Pioneer SH-D505 User manual

Pioneer

Pioneer F-99X User manual

Pioneer

Pioneer GEX-P920XM - XM Radio Tuner User manual

Pioneer

Pioneer XC-IS21MD User manual

Pioneer

Pioneer SH-D505 User manual

Pioneer

Pioneer TS5 User manual

Pioneer

Pioneer XC-IS21MD User manual

Pioneer

Pioneer XV-DV88 User manual

Pioneer

Pioneer ND-MDT10 User manual

Pioneer

Pioneer GEX-M7347XMZH/XN/UC User manual

Pioneer

Pioneer TX-5300 User manual

Pioneer

Pioneer F-91 User manual

Pioneer

Pioneer DEH-2800MP/XU/UC User manual

Pioneer

Pioneer TX-520 User manual

Pioneer

Pioneer F-91 User manual

Pioneer

Pioneer DC-888Z User manual

Pioneer

Pioneer F-93 User manual

Pioneer

Pioneer XV-DV55 User manual

Popular Tuner manuals by other brands

Tunersys

Tunersys WS16 1 quick start guide

Arcam

Arcam DT91 Handbook

Magnum

Magnum MD 102T instruction manual

HDHomeRun

HDHomeRun 20121008 installation instructions

Crestron

Crestron C2N-TXM Operation guide

Eico

Eico HFT-92 instruction manual

MFJ

MFJ MFJ-928 instruction manual

NAD

NAD C 445 owner's manual

Sony

Sony ST-SA5ES operating instructions

Sirius Satellite Radio

Sirius Satellite Radio SC-FM1 user guide

Antique Automobile Radio

Antique Automobile Radio 283501B Installation and operating instructions

Monacor

Monacor PA-1200R instruction manual

Technics

Technics ST-X301L Service manual

Manhattan

Manhattan 176156 user manual

Marantz

Marantz ST-15S1 user guide

Korg

Korg HA-40 owner's manual

Harman Kardon

Harman Kardon TU915 Technical manual

Teac

Teac T-1D Service manual