Pinnacle MASTER MH-360A-TTC Training manual

MODEL NUMBERS

MH-16-TTC / MH-32-TTC / MH-360A-TTC

User’s Manual &

Operating Instructions

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS

HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE

FROM HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, CARBON MONOXIDE POISONING

AND / OR ELECTRIC SHOCK.

ONLY PERSONS WHO CAN READ, UNDERSTAND, AND FOLLOW THE INSTRUCTIONS IN THIS

MANUAL SHOULD USE, SERVICE OR MAINTAIN THIS HEATER. IF YOU NEED ASSISTANCE OR

HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABEL, ETC. CONTACT THE

MANUFACTURER.

DANGER

CONSUMER: READ AND RETAIN THESE INSTRUCTIONS FOR FUTURE USE

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES,

SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE AWAY

FROM THE HEATER AS RECOMMENDED BY THESE INSTRUCTIONS. NEVER USE THE HEATER IN

SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS

SUCH AS GASOLINE, SOLVENTS, PAINT THINNERS, DUST PARTICLES OR UNKNOWN CHEMICALS.

WARNING

Factory ID: 522 Sauk Rapids, MN 56379 USA • Toll Free (800) 641-6996

Fax: 320-251-2922 • Web: www.masterindustrialproducts.com • Email: [email protected]

PROPANE TANK TOP

HEATER

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag.

It will begin with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your

Serial Number ready before calling customer service at 800-641-6996.

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR:

The temporary heating of adequately ventilated buildings or

structures under construction, alteration or repair.

FOR INDOOR USE, PERMITTED ONLY FOR: The temporary

heating of adequately ventilated buildings or structures

under construction, alteration or repair.

MH-16-TTC / MH-32-TTC MH-360A-TTC

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

TABLE OF CONTENTS

Safety Information......................................................2-5

Speciﬁcations..................................................................6

Features........................................................................6-7

What’s in the Box............................................................8

Assembly

....................................................................

9-10

Operation.....................................................................11-13

Maintenance and Storage...........................................13

Troubleshooting Guide.................................................14

Exploded View

.........................................................

...

.15

Parts List..........................................................................15

Warranty...........................................................................16

SAFETY INFORMATION

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

WARNING

This is an unvented portable heater. It uses air (oxygen) from the area in which it is

used. Adequate combustion and ventilation air must be provided. Refer to VENTILA-

TION on Page 12. Do not override safety devices.

WARNING

Carbon Monoxide Hazard This heater produces carbon monoxide, which has no

odor. Burning the heater in an enclosed space can kill you. Never use the heater in

enclosed spaces such as a tent, a camper, any vehicle or recreational vehicle (RV), enclosed shelter,

or any other enclosed areas.

DANGER

Not for use in residential living areas or in non-adequately ventilated enclosed spac-

es. Never bring or store a propane cylinder indoors.

DANGER

This heater is designed and approved for use as a construction heater in accordance with Standard

ANS Z83.7 • CSA 2.14-2017 Construction Heater. CHECK WITH YOUR LOCAL FIRE SAFETY

AUTHORITY IF YOU HAVE ANY QUESTIONS ABOUT APPLICATIONS. Other standards govern the

use of fuel gasses and heating products for specific uses. Your local authority can advise you about

these.

If the information in this manual is not followed exactly, a ﬁre or explosion may result

causing property damage, personal injury or loss of life.

DANGER

DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY UN-

DERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS.

Failure to comply with the precautions and instructions provided with this heater can result in death,

serious bodily injury, property loss or damage from the hazards of ﬁre, explosions, burns, asphyxiation

or carbon monoxide poisoning. Only persons who can read, understand, and follow the instructions in

this manual should use, service or maintain this heater.

WARNING

Do not use with or around birds, foul, or poultry.

DANGER

WARNING: This product can expose you to chemicals, including lead, which is known to the State

of California to cause cancer and birth defects or other reproductive harm. For more information

go to www.P65Warnings.ca.gov.

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

SAFETY INFORMATION

The products described in this manual are pro-

pane direct-ﬁred heaters. Direct-ﬁred means that

all of the combustion products of the heater enter

the heated space. This appliance is rated at 98%

combustion eciency, but does produce carbon

monoxide.

Carbon monoxide is toxic. Humans can tolerate

only small amounts of carbon monoxide and so

precautions should be taken to provide proper

ventilation. Failure to provide proper ventilation

in accordance with the instructions in this manual

can result in death.

People with breathing problems should consult a

physician before using this heater.

Early signs of carbon monoxide poisoning re-

semble the ﬂu. Symptoms of improper ventilation /

carbon monoxide poisoning are:

Headache • Dizziness • Nausea • Dry Mouth

Sore Throat • Burning of Nose and Eyes

If you experience any of these symptoms:

GET FRESH AIR AT ONCE! Have your heater

serviced and check for proper ventilation. Some

people are more affected by carbon monoxide

than others. These include: pregnant women,

those with heart or lung problems, anemia or those

under the influence of alcohol or at high altitudes.

WHAT TO DO IF THE SMELL OF GAS IS PRESENT:

–DO NOT attempt to light the heater.

–Extinguish any open ﬂame.

–Shut o gas to heater.

–If odor continues, immediately contact your

local ﬁre department.

–DO NOT touch or use any electric switch or

any electric device that can cause a spark.

–Service must be done by a qualiﬁed service

agency.

NEVER store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this heater.

NEVER store

a propane (LP) cylinder not connected

to this heater in the vicinity of this heater.

NEVER

connect heater to an unregulated gas supply.

NEVER

obstruct the ﬂow of combustion and

ventilation air. (The front and rear of heater).

NEVER use duct work in front or rear of heater.

NEVER modify this heater or operate a heater that

has been modiﬁed.

NEVER service, move or handle heater while still hot

or operating

NEVER use heater in occupied dwellings.

NEVER use heater in a tent.

NEVER alter or override safety devices.

NEVER place heater on unstable surfaces such as

chairs, stools, tables, or on wheels.

RISK OF INDOOR AIR POLLU-

TION!

WARNING

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

DANGER

RISK OF BURNS, FIRE AND EX-

PLOSION!

WARNING

PROPANE IS AN

EXPLOSIVE GAS!

DANGER

MH-16-TTC / MH-32-TTC

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR: The temporary heating of

adequately ventilated buildings or structures under construction, alteration or repair! Provide at least a

three square foot (2,800 sq cm) opening of outside air for every 100,000 Btu / Hr heater rating. Refer to

“Ventilation” on page 12 for further instructions.

MH-360A-TTC

FOR INDOOR USE, PERMITTED ONLY FOR: The temporary heating of adequately ventilated

buildings or structures under construction, alteration or repair! Provide at least a three square foot

(2,800 sq cm) opening of outside air for every 100,000 Btu / Hr heater rating. Refer to “Ventilation” on

page 12 for further instructions.

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

–Do not use this heater for heating human living

quarters

–Use of direct-fired heaters in the construction

environment can result in exposure to levels of

CO, CO₂, and NO₂considered to be hazardous

to health and potentially life threatening

–Do not use in unventilated areas

–Know the signs of CO and CO₂poisoning

•Headaches, stinging eyes

•Dizziness, disorientation

•Difficulty breathing, feels of being

suffocated

–Proper ventilation air exchange (OSHA 29

CFR 1926.57) to support combustions and

maintain acceptable air quality shall be

provided in accordance with OSHA 29 CFR

Part 1926.154, ANSI A10.10 Safety Requirements

for Temporary and Portable Space Heating

Devices and Equipment used in the

Construction Industry or the Natural Gas and

Propane Installation Codes CSA B149.1

–Periodically monitor levels of CO, CO₂and

NO₂existing at the construction site – at the

minimum at the start of the shift and after 4

hours.

–Provide ventilation air exchange, either

natural or mechanical, as required to maintain

acceptable indoor air quality

–Ensure that the flow of combustion and

ventilation air exchanges cannot become

obstructed

–As the building “tightens up” during the

construction phase ventilation may need to be

increased

AIR QUALITY HAZARD

WARNING

SAFETY INFORMATION

USA 8-Hr Time Weighted Average

(OSHA 29 CFR 1926.55 App A)

Canada 8-hr Time Weighted Average Work-

Safe BC OHS Guidelines Part 5.1 and Ontario

Workplaces Reg 833

CO 50 ppm 25 ppm

CO₂ 5000 ppm 5000 ppm

NO₂ 3 ppm (Reg 833)

USA – Ceiling Limit

(Short Term Exposure Limit = 15 minutes)

Canada STEL (15 minutes Reg 833/1 hour

WSBC) WorkSafe BC OHS Guidelines Part 5.1

and Ontario Workplaces Reg 833

CO 100 ppm

CO₂ 15000 ppm (WSBC)

30000 ppm (Reg 833)

NO₂ 5 ppm 1.0 ppm (WorkSafeBC)

5.0 ppm (Reg 833)

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Keep this heater clear and free from all combustible

materials, gasoline, and other ﬂammable vapors and

liquid.

Minimum Clearance From Combustibles

Sides Top Front Rear

MH-16-TTC 3 ft. 5 ft. 5 ft. 3 ft.

MH-32-TTC 3 ft. 5 ft. 5 ft. 3 ft.

MH-360A-TTC 5 ft. 5 ft. 5 ft. 5 ft.

For installation on combustible ﬂooring as a free

standing unit with the following minimum clearances

from combustible construction:

Top: 5 ft. Front: 5 ft. Sides: 3 ft. (5 ft*)

Rear: 3 ft. (5 ft.*) Floor: Combustible

*MH-360A-TTC only

It is the owner’s responsibility to communicate

combustible clearances with others.

ALWAYS install the heater so that it is not directly

exposed to water spray, rain, dripping water, or wind.

ALWAYS provide adequate clearance for accessibility,

combustion and ventilation (air supply) while heater is

operating.

–Use heater in accordance with all local codes.

In the absence of local codes, refer to The

National Fuel Code, ANSI Z223.1.

–This heater is shipped from the factory

for use with propane (LP) gas only. Do not

convert to any other gas. Installation must

conform to local codes, or in their absence,

with the standard for the Storage and Handling

of Liquefied Petroleum Gases ANSI/NFPA 58

and the Natural Gas and Propane Installation

Code CSA B149.1.

–Gas supply connections should be checked by

using a 50/50 soap and water solution. Never

use a ﬂame to check for gas leaks.

–Do not direct heater discharge towards the LP

cylinder unless it is at least 20 feet from the

heater.

–Use only the regulator and hose assembly

provided with this heater. Inspect the

regulator/hose assembly prior to each use

of the heater. If there is excessive abrasion

or wear, or if the hose is cut, replace it with

the proper assembly shown in the parts list

following manufacturer’s speciﬁcation, prior to

using the heater.

Minimum and Maximum Inlet Pressure

MH-16-TTC MH-32-TTC MH-360A-TTC

Min. 25 PSI

Max. 200 PSI

SAFETY INFORMATION

The hose assembly shall be

protected from trac, building

material and contact with hot surfaces both

during use and while in storage.

WARNING

RISK OF FIRE! ALWAYS ATTACH THE HEATER IN AN UPRIGHT VERTICAL

POSITION. ALWAYS LOCATE HEATER ON A STABLE AND LEVEL SURFACE!

WARNING

CAUTION! HOT WHILE IN OPER-

ATION. DO NOT TOUCH. KEEP

CHILDREN, ANIMALS, CLOTHING AND COM-

BUSTIBLES AWAY FROM HEATER.

WARNING

For use with propane (LP)

gas only.

WARNING

DO NOT use any LP cylinder

larger than 20 lbs.

WARNING

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

FEATURES

MH-16-TTC

Regulator

SPECIFICATIONS

Model # MH-16-TTC MH-32-TTC MH-360A-TTC

BTU 16,000 32,000 41,000

Heat Settings Low, Medium, High Low, Medium, High Low, Medium, High

Fuel Consumption (Lbs./hr) 0.56 / 0.65 / 0.74 1.16 / 1.30 / 1.49 1.24 / 1.56 / 1.87

Maximum Operating Hours 35.9 / 30.8 / 27.0 17.2 / 15.4 / 13.4 16.0 / 13.0 / 10.0

Required Cylinder Lbs. Use ONLY 20 lb. LP Gas

Cylinder: 18" x 12.25"

Use ONLY 20 lb. LP Gas

Cylinder: 18" x 12.25"

Use ONLY 20 lb. LP Gas

Cylinder: 18" x 12.25"

Fuel Type Propane Propane Propane

Heating Area (Ft.2) 300 / 350 / 400 620 / 700 / 800 660 / 840 / 1025

Specications subject to change without notice.

Front Guard

Heat Reﬂector

Rear Guard

Ignition Hole

Tip Over Switch

Safety Valve

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

FEATURES CONT.

MH-32-TTC

Regulator

Front Guard

Heat Reﬂector

Rear Guard

Ignition Hole

Tip Over Switch

Safety Valve

MH-360A-TTC

Mounting Bolt Knob

Hose

Heat Reﬂector

Safety Valve

Mounting Bolt Knob

Hose

Regulator

Guard

Ignition Hole

Tip Over Switch

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

WHAT’S IN THE BOX

MH-16-TTC

MH-32-TTC

MH-360A-TTC

(1) Mount and Unit with Single

Burner Head

(1) Unit with Two Burner

Heads

(1) Mount

(1) Mount and Unit with Single

Burner Head

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

ASSEMBLY

Model MH-32-TTC:

Tools Needed:

–Medium Phillips head screwdriver.

1. Place the tank collar bracket on top of the

center plate. Be sure the mounting bolt knob is

on bottom as shown in Figure 1.

2. Insert machine screw into top hole using

Phillips head screwdriver.

3. Insert 2nd machine screw into bottom hole.

This will secure the tank collar bracket to the

center plate.

Model MH-360A-TTC:

Tools Needed:

–Medium Phillips head screwdriver.

1. Insert the mounting bolt knob into the tank

collar bracket.

2. Place tank collar bracket on the swivel bracket.

3. Place the plane washer on the tank collar

bracket and then insert the support bolt

(see Figure 2)

DO NOT adjust burner heads while heater is operating.

WARNING

Regulator

Knob

Fuel Connector Nut

Machine

Screws

Mounting Bolt Knob

Tank Collar Bracket

Tip over Switch

Assembly

Swivel

Manifold

Figure 1 Figure 2

Regulator

Knob

Tip Over Switch

Assembly

Fuel Connector

Nut

Tank Collar

Bracket

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

ASSEMBLY

Connecting Heater to LP Cylinder:

Be sure to read and understand all of the Safety

Information in this manual before connecting

the heater to the LP cylinder. Installation must

conform to local codes and with the Standard for

the Storage and Handling of Liquefied Petroleum

Gasses and ANSI/NFPA 58 and the Natural Gas

and Propane Installation Code, CSA B149.1.

Inspect the hose and regulator prior to each

use of the heater. If there is excessive abrasion

or wear, or if the hose is cut, replace it with the

proper assembly shown in the parts list prior to

using the heater.

Model MH-16-TTC/MH-360A-TTC:

1. Be sure that the control knob on the regulator is

in the “OFF” position.

2. Line up the threads on the fuel connector nut

with the threads on the LP cylinder valve. Turn

fuel connector nut COUNTERCLOCKWISE to

tighten. Fully tighten the nut, being careful not to

over tighten.

3. Slowly open the LP cylinder valve.

Models MH-32-TTC:

1. Be sure that the control knob on the regulator is

in the “OFF” position.

2. Line up the slots in the tank collar bracket with

the tank collar ring and slide into place. Be

sure the mounting knob is to the outside, and

tighten.

3. Line up the threads on the fuel connector nut

with the threads on the LP cylinder valve. Turn

fuel connector nut COUNTERCLOCKWISE to

tighten. Fully tighten the nut, being careful not to

over tighten.

4. Slowly open the LP cylinder valve.

Check all connections for leaks using a 50/50

mixture of dish-soap and water. Any bubbles

that appear show a leak. Remove and reconnect

the Connector Nut to the valve.

DO NOT direct the heater discharge towards any propane cylinder located

within 20 feet of the heater.

WARNING

Remove the heater from the LP cylinder by reversing

the steps in Connecting Heater to LP Cylinder on

Page 9. DO NOT store the LP cylinder with the

heater still attached or in an enclosed area.

This manual suits for next models

Table of contents

Languages:

Other Pinnacle Heater manuals

Pinnacle

Pinnacle MASTER MH-80-OFR Training manual

Pinnacle

Pinnacle ProTemp PT-125-OFR-A Manual

Pinnacle

Pinnacle Protemp PT-80V-LPC-A Training manual

Pinnacle

Pinnacle Heat-Stream HS-18-PCH Manual

Pinnacle

Pinnacle ProTemp PT-80-OFR Training manual

Pinnacle

Pinnacle REMINGTON REM-45-KFA-O Training manual

Pinnacle

Pinnacle Master MH-70-SS-A Training manual

Pinnacle

Pinnacle MASTER MH-03-240-GH User manual

Pinnacle

Pinnacle REMINGTON REM-16-TTC-O Training manual

Pinnacle

Pinnacle Protemp PT-150T-DFV Training manual

Pinnacle

Pinnacle Protemp PT-35-HS Manual

Pinnacle

Pinnacle Remington REM-40-GFA-B Training manual

Pinnacle

Pinnacle Master MH-16-TTC Training manual

Pinnacle

Pinnacle ProTemp PT-18PNCH-A Training manual

Pinnacle

Pinnacle HEAT-STREAM HS-45-KFA Manual

Pinnacle

Pinnacle Remington REM-45-KFA-B Training manual

Pinnacle

Pinnacle MH-45-KFA Training manual

Pinnacle

Pinnacle Remington REM-360A-TTC-O Training manual

Pinnacle

Pinnacle Protemp PT-170T-IDF-EU Manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide