Pickering 40-252 User manual

pickeringtest.com

Issue 1.4 January 2020

40-252 User Manual

PXI 5W Programmable Resistor Module

Page (II) 5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) 5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Guidance on Using the Module............................................2.2

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options For Pickering PXI Modules ............4.1

Module Architecture..............................................................4.2

Programming Module............................................................4.2

Using The Soft Front Panel ..................................................4.4

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting .........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Verication & Adjustment Procedure ..................................7.2

Verication Test Results .......................................................7.9

CONTENTS

Page (VI) 5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) 5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

PXI 5W Programmable Resistor Module 40-252

ISSUE F NOV 2019

Up to 4

37-pin

D-type

Plug

Resistor

Channel

Switched

Resistor

Functional Diagram for the 40-252 5W

Programmable Resistor Module

• Up To 5W Per Channel

• Up To 4 Channels in a One Slot Module

• Resistance Resolution to 0.125Ω

• Values From 1Ω to 22MΩ

• Short and Open Simulation

• Simple Software Control Through

Resistance Calls

• VISA & Kernel Drivers Supplied for

Windows

• Supported by PXI or LXI Chassis

• 3 Year Warranty

Part of a growing range of medium to high power

resistor modules, the 40-252 provides a simple

solution for applications requiring up to 5W of power

handling capability. The 40-252 is available in a

variety of resistance ranges and resolutions that

meet the needs of most functional test systems.

Each channel of the 40-252 is able to simulate

short circuit and open circuit conditions that can be

experienced in a system caused by faulty wiring or

sensors.

Software control is simplied by the use of resistor

value calls. The module works out the resistance

setting closest to the requested value and sets that

value. The user can interrogate the module to nd

the actual setting used.

A calibration cable assembly can be attached to

the module in place of the UUT to enable a DMM

to be used for verifying the resistor channels. This

considerably simplies the checking of the module’s

calibration.

The 40-252 is available in 40 standard builds that suit the most common

congurations:

• Narrow resistance range version, available in 2 or 4 channel variants.

• Medium resistance range version, available in 1 or 2 channel variants.

• Wide resistance range version, available in 1 channel variants.

For applications requiring greater density with lower power, users should

consider the 40-297 High Density Precision Resistor Modules.

Pickering’s Range of PXI Resistor Modules

Model No. Description Channels Range

40-251 2.5W Programmable Resistor 1, 2, 4 or 8 Up to 22MΩ

40-252 5W Programmable Resistor 1, 2, or 4 Up to 22MΩ

40-253 10W Programmable Resistor 1 or 2 Up to 102kΩ

40-280/1/2 Selectable 12 to 48 User Specied

40-290 Programmable Resistor 20.5Ω to 32kΩ

40-291 4 0.5Ω to 128Ω

40-292 Programmable Load 1 40Ω to 295Ω or

10Ω to 2.56kΩ

40-293 Programmable Resistor + SPDT 2 or 4 Up to 131kΩ

40-294 Programmable Resistor + SPST 2 or 4 Up to 131kΩ

40-295 Programmable Resistor 3, 6, 5,

10 or 18 Up to 16MΩ

40-296 Programmable Potentiometer 1, 2, 3, 4,

5 or 9 Up to 16MΩ

40-297 High Density Precision Resistor 3, 4, 6,

9 or 18 Up to 22.3MΩ

40-298

Precision Resistor Modules

For applications requiring a Resistor Module with greater resolution (to <2mΩ) or better

accuracy (to <0.03%), look to our Precision Resistor range which includes models

40-260, 40-261, 40-262, 40-265, and 40-297

Custom Resistor Modules

If our range of Resistor Modules does not meet your specic requirements, please

contact you local sales ofce to discuss your application. Customizations include:

different start and stop values, current, power, voltage, precision, accuracy, number of

channels, connector etc.

Page 1.2 5W PROGRAMMABLE RESISTOR MODULE 40-252

pickering

SECTION 1 - TECHNICAL SPECIFICATION

5W Programmable Resistor – 40-252

pickeringtest.com

Overview

Soft Front Panel for the Programmable Resistor Module

Graphical Representation of the 40-252 Programmable Resistor Module Range

PXI Part Number

(Number of Channels)

Resistance Range

Resolution

1Ω 10Ω 100Ω 1kΩ 10kΩ 100kΩ 1MΩ 10MΩ 100MΩ

40-252-010 (4) 40-252-110 (2) 0.125Ω

40-252-011 (4) 40-252-111 (2) 0.25Ω

40-252-012 (4) 40-252-112 (2) 0.5Ω

40-252-013 (4) 40-252-113 (2) 1Ω

40-252-014 (4) 40-252-114 (2) 2Ω

40-252-020 (2) 40-252-120 (1) 0.125Ω

40-252-021 (2) 40-252-121 (1) 0.25Ω

40-252-022 (2) 40-252-122 (1) 0.5Ω

40-252-023 (2) 40-252-123 (1) 1Ω

40-252-024 (2) 40-252-124 (1) 2Ω

40-252-030 (2) 40-252-130 (1) 0.125Ω

40-252-031 (2) 40-252-131 (1) 0.25Ω

40-252-032 (2) 40-252-132 (1) 0.5Ω

40-252-033 (2) 40-252-133 (1) 1Ω

40-252-034 (2) 40-252-134 (1) 2Ω

40-252-040 (1) 0.125Ω

40-252-041 (1) 0.25Ω

40-252-042 (1) 0.5Ω

40-252-043 (1) 1Ω

40-252-044 (1) 2Ω

40-252-050 (1) 0.125Ω

40-252-051 (1) 0.25Ω

40-252-052 (1) 0.5Ω

40-252-053 (1) 1Ω

40-252-054 (1) 2Ω

This manual suits for next models

Table of contents

Other Pickering Control Unit manuals

Pickering

Pickering 40-580 User manual

Pickering

Pickering PXI 40-855 User manual

Pickering

Pickering 40-573 User manual

Pickering

Pickering 40-290-021 User manual

Pickering

Pickering PXi 41-720 User manual

Pickering

Pickering 40-574 User manual

Pickering

Pickering 40-650A User manual

Pickering

Pickering 40-727 User manual

Pickering

Pickering 40-575 User manual

Pickering

Pickering 42-724 User manual

Pickering

Pickering 40-331 User manual

Pickering

Pickering 40-296 User manual

Pickering

Pickering 40-592A User manual

Pickering

Pickering PXI 40-145 User manual

Pickering

Pickering 40-500 User manual

Pickering

Pickering 40-545 User manual

Pickering

Pickering 40-565A User manual

Pickering

Pickering 40-884 User manual

Pickering

Pickering 40-191B User manual

Pickering

Pickering PXI 40-664A User manual

Pickering

Pickering PXI BRIC 40-569 User manual

Pickering

Pickering SYSTEM 10 User manual

Pickering

Pickering 41-735 User manual

Pickering

Pickering PXI 60-104 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual