Phoenix SS1190E Citadel User manual

SS1190E Citadel Instructions

a) To switch on the lock power supply, press button <<ON>>.

b) The lock is set on the factory default code of 1,2,3,4,5,6.

c) Enter the default code (1,2,3,4,5,6) the correct code is confirmed by the flashing green LED.

1. Lock opening

The new code combination should be entered with the lock and safe door in the open postion.

a) Open the lock with the valid primary code (see 1.);

Press <<ON>>;

Press button <<P>>.

Enter valid code 1-2-3-4-5-6 or former user code (if the green LED is illuminated continuously, the operation is correct completed);

Enter new 6-digit code X-X-X-X-X-X (if after entering the green LED is illuminated continuously and acoustic signal sounds twice,

the operation is correct).

Repeat the procedure again: Enter the new 6-digit code X-X-X-X-X-X (if after entering the green LED is illuminated continuously and

acoustic signal sounds twice, the operation is correct ) and the new code is set.With the door in the open position test the new 6-digit

X-X-X-X-X-X again (if after entering the green LED flashes once, the operation is completed). The door can be opened.

It is recommended to record the new code combination and to safely store it outside the safe.

2. Change of Code Combination

If the code is entered incorrectly the red LED flashes 3 times. After 3 incorrect entries the lock goes into a two minute blocked status. The period

in which the lock is blocked is extended to 4,8 and a maximum of 16 digits every time an incorrect code is entered.

3. Lock blocking

Turn the bar handle counter clockwise in “close”-position until stop reached. The lock is blocked (bar handle is in horizontal position).

4. Locking

Low voltage is indicated, if the red LED flashes 10 times after opening. Please change the battery immediately. Open the safe, lift out the battery

cover on the inner side of the door (figure 2.) insert the new 9v battery;

Code combination remains saved even if battery is discharged

If the battery is not charged and the lock is not receiving sufficient power to open, a new battery can be connected by an external supply clip.

The supply clip is located on the control panel under the logo sticker KABA * (Figure 3).

5. Power Supply / Changing the batteries

123

45 6

789

0 P

Figure 1. Appearance

Figure 3. Battery outer connection

123

45 6

789

0 P

Figure 2.

Base fixing instructions for the

SS1190E Citadel Series

a) To switch on the lock power supply, press button <<ON>>.

b) The lock is set on the factory default code of 1,2,3,4,5,6.

c) Enter the default code (1,2,3,4,5,6) the correct code is confirmed by the flashing green LED.

YOU WILL REQUIRE

1) Look for a place that does not restrict access and the swing of the door.

2) Ensure that the floor is level.

3) For best results a concrete floor is preferable.

CHOOSING A PLACE TO INSTALL YOUR SAFE

1) Manoeuvre the safe into the required position. Now with the pencil mark the floor around the safe. (If the safe is against a wall then just the

front and sides needs to be marked)

2) Open the safe door.

3) Remove the bolt cover tray on the bottom of your safe to reveal the base fixing holes.

4) Mark the positions on the floor for drilling. Use the pencil through the base fixing holes in the base of the safe.

5) Now move the safe to one side, giving you access to the markings on the floor

6) Before using the 20mm drill bit. With the ruler measure 120mm from the tip of the bit and put a piece of adhesive tape around the bit to

ensure you do not drill too deep.

7) Drill the 20mm holes in the floor until you reach your 120mm adhesive tape marker.

8) Clean around both of the holes in the floor.

9) There are four parts to each of your two bolts

a. A socket head bolt

b. A washers (steel)

c. A 24mm washer with a 30mm spacer welded to it

d. 74mm shield

10) Take the washer with spacer attached and insert it into the hole in the ground, now with the pencil drawer around the washer. Now remove

the washer/spacer and with the large screwdriver gouge out the surface around the holes to a depth of 2.5mm. This will let the washers sit

flush with the floor.

11) Take the 74mm shields and the 30mm spacers, insert these into the drilled holes. The shield first with the plastic cap covering the end going

down the hole first.

12) Place the safe back into position, using the pencil lines on the floor. Now place the steel washers onto the bolts and insert the bolts through

the base of the safe, into the floor and right down through the spacer into the shield and tighten until you can not turn the Allen key any further.

13) Replace the bolt cover tray.

YOUR SAFE IS NOW BASE FIXED.

DRILLING & BOLTING

Version 1/JPT/Sept 11

Thank you for purchasing a Phoenix Safe. Your safe is ready prepared for base fixing. To base fix your safe, follow instructions below.

HOW TO BOLT YOUR SAFE DOWN

Table of contents

Other Phoenix Safe manuals

Phoenix

Phoenix VENUS HS0656 Product information sheet

Phoenix

Phoenix FS1280F User manual

Phoenix

Phoenix SS0935E Series User manual

Phoenix

Phoenix KS0002C User manual

Phoenix

Phoenix SS0720E Series User manual

Phoenix

Phoenix GS8015K Product information sheet

Phoenix

Phoenix Diamond Deposit HS1090ED User manual

Phoenix

Phoenix SS1180K User manual

Phoenix

Phoenix KS0030E Series User manual

Phoenix

Phoenix FIRE COMMANDER PRO FS1920 Product information sheet

Phoenix

Phoenix VENUS HS0650 Product information sheet

Phoenix

Phoenix SS1190E Series User manual

Phoenix

Phoenix Mercury HS2050 Manual

Phoenix

Phoenix GS8010K Product information sheet

Phoenix

Phoenix KS0030E Series User manual

Phoenix

Phoenix SS1160F Product information sheet

Phoenix

Phoenix FS0440E User manual

Phoenix

Phoenix DS4620E User manual

Phoenix

Phoenix KS0030E User manual

Phoenix

Phoenix FS2250K Series User manual

Phoenix

Phoenix NESO SS0200F Series User manual

Phoenix

Phoenix FS0352C Series User manual

Phoenix

Phoenix NEPTUNE HS1056 Product information sheet

Phoenix

Phoenix FS1510E Series User manual

Popular Safe manuals by other brands

Squire

Squire Stronghold Keysafe Fitting instructions

Vaultek

Vaultek 10 Series Quick setup

Arregui

Arregui CLASS operating instructions

Beaumont

Beaumont SMART KEYBOX user guide

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe user guide

Hornady

Hornady SnapSafe Trunk Safe II owner's manual

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO instruction manual

Honeywell

Honeywell 5912 user guide

Technomax

Technomax Trony Series Instruction handbook

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series instruction manual

RICHTER CZECH

RICHTER CZECH LA Instructions for use and installation

Olymp

Olymp GOsafe 110 operating instructions

Clarke

Clarke Strong-Arm CS1000K Operation & maintenance instructions

Ankaro

Ankaro ANK EZ I quick start guide

Intratone

Intratone KEY SAFE installation and connection

Costway

Costway HW50956 user manual

Megasat

Megasat K Series quick start guide

ECOSAFE

ECOSAFE 3030ARD instruction manual