Phoenix Doors Enviro 6S User manual

Sliding Gate Operator

User's Manual

E N V I R O 6 S

G e a r -D r i v e n

http://www.phoenixgaragedoors.com.au/

ENVIRO 6S SLIDING GATE OPERATOR

OUTLINE

1. Products introduction 2

2. Important safety precautions 2

3. Main technical parameters 2

4. Mechanical Installation 3

5. Adjustment5

6. Wire Connecting 6

7. Electrical and control board 7

8. Porgramming Process 8

9. Maintenance 10

10. Trouble Shooting 11

11. Packing list 11

12. Warranty Registration 11

ENVIRO 6S SLIDING GATE OPERATOR

1. Products introduction

please read the instructions carefully before proceeding.

The operator contains Extra battery, transformer, control board and radio control.

In case of power of failure, the operator is powered by a 24Vdc, 1.3Ah, extra battery.

Intelligent charging system supplied.

MCU is supplied to control the gate operator.

Keypad / single button interface.

Photo beam safety beam interface.

User can select Auto-close feature

Soft start & soft stop.

Manual key release design for emergency purposes.

Gate operator has auto-reverse function, and the reverse power can change by user.

2. Important safety information

Carefully read and follow all safety precaution and warnings before attempting to install and use this

automatic gate operator.

Make sure the Power supply(AC220V) of operator is suitable for the power supply in your area.

3. Main technical parameters

Unit Model ENVIRO 6S

Power Supply 220VAC

220V AC

110V AC

Maximum gate weight 300Kg

Maximum gate width 8m

Motor 24VDC 100W

Output torqueMax. 8N m

Work duty S

30min

Limit switch

Electronical Limit

Gate Move speed13m/min

Remote control range30 meters

extra remote control 20

100 (2 included)

Frequency 433.92 MHz

Noise 60 dB

Working temperature -20 C ~ +50 C

Extra Battery 24V 1.3 Ah

ENVIRO 6S SLIDING GATE OPERATOR

4. Mechanical Installation

The ENVIRO 6S will handle gate weighting up to 300Kg and up to 8m if the proper installation procedures

have been followed.

The ENVIRO 6S gate operator operates by forcing a drive rack by a drive gear. The entire configuration

is shown in the diagram below. The gate operator must be installed on the inside of the gate.

Sliding gate

Gate operator

Rack

Switch

Input power

Wall

Fig.1

Gate preparation

Be sure the gate is properly installed and slides smoothly before installing the ENVIRO 6S sliding gate

operator. The gate must be plumb, level, and move freely.

Conduit

In order to protect the wires, use PVC conduit for low voltage power cable and control wires. Conduit

must be preset into the concrete when it is poured. Wires within the conduit shall be located or protected

so that no damage can result from contact with any rough or sharp part.

Concrete pad

The base unit of the gate operator requires a concrete pad in order to maintain proper stability. The

concrete pad should be approximately 400mm x 250mm x 200mm deep in order to provide for adequate

weight and structure to insure proper stable installation.

Anchors (see Fig.2)

You can use anchor bolts, anchors, washers and nuts. These anchors must be set into the concrete

when it is poured or you can use wedge anchors to fasten the operator.

ENVIRO 6S SLIDING GATE OPERATOR

Gate operator

Gear

Groundsill

Input power

Plain washer

Nut

Spring washer

Nut

Fig.2

Operator base (see Fig.3)

After the concrete has hardened, mount the gate operator base to the concrete pad. Verify that the base

is properly leveled.

Using bolts and washers mount the gate operator to the base and insert the cover. Check the operator

and make sure it is lined up with the gate.

Fig.3

ENVIRO 6S SLIDING GATE OPERATOR

Installation of Rack

Fix the three nuts (in the same package with rack) on the rack element.

Laythe first piece of rack on the gear and weld the first nut on the gate.

Move the gate manually, checking if the rack is resting on the gear, and weld the second and third nut.

Bring another rack element neartothe previous one. Move the gate manually and weld the three nuts

as the first rack, thus proceeding until the gate isfully covered.

When the rack has been installed, to ensure it meshes correctly with the gear.

The space between rack and gearis about 0.5mm.

Fig.4

5. Adjustment

Sliding gate

Rack

Gear

Fig.5

ENVIRO 6S SLIDING GATE OPERATOR

Manual operation

In case of power failure use manual release key to open or close gate manually, use the release key as

follow:

Fit the supplied key in the hole.

Turn the key clockwise to release the clutch.

Open and close the gate manually.

After power-restored use the manual release key totight the clutch by turning the key

counterclockwise and resume normal operation.

Fig.6

NOTE The gate operator needed reset limit after re-tight the clutch by turning the key

counterclockwise if the power failure and released by hand.

6. Wire Connecting

Connecting the battery

Plug the terminal of Extra battery in the control board.

NOTE:If you not use gate operator and power failure, please pull out the extra battery terminal.

Fig.7

Release

Release keyRelease hole

Battery

BLACK TO Charge BAT -

RED TO Charge BAT +

Battery

RED TO SOLAR BAT +

BLACK TO SOLAR BAT -

SOLAR PANEL

ENVIRO 6S SLIDING GATE OPERATOR

Connecting the motor

Connect motor wires to M- and M+ of terminal block T1 (BLACK)and T2(RED).

Connecting power wire

Fig.8

7.Electrical and control board

Fig.9

Motor: black wire to T1 and red wire to T2.

J1: transformer secondary(AC24V/3.3A)

external Push Button(J2,J3,J4):

Single Button(OSC and COM)

Three Button(K,G,T,and COM),

Photo beam(PE and COM)

Output DC power: 24 and GND

J5: solar panel(10W 27V) and charge Battery.

NOTE: Please put through the J5 (Battrey) terminal, if you need use the sliding gate

Transformer

primary

Power

supply

AC220V

ENVIRO 6S SLIDING GATE OPERATOR

operator.

8. Programming Process

SET button: Mode set and Confirm function

CODE button: Transmitter set and clear function

OPEN button: open door

CLOSE button: close door

SET CODE

OPEN

Fig.10

Adding extra transmitter (learn)

1. Press CODE, a dot is indicated on the LED display.

2. Press the transmitter button which you want to use (button 1, 2, 3, 4), then press the same button

again.

3. The dot on the LED display will flash then turn off.

4. ’||’ is indicated on the LED display, then the learning process is finished.

Up to 20 transmitters may be used.

SET CODE

CODE

SET SET CODE

OPEN

Fig.11

Erase transmitter

Press and hold CODE until ’C’ flashes on the LED display. This indicates that all the transmitters have

been erased completely.

SET CODE

OPEN

Fig.12

ENVIRO 6S SLIDING GATE OPERATOR

Set open and close positions

1. Press and hold SETuntil number 1is indicated on the LED display.

2. Press and hold OPENto set open position(now the door must be OPEN,, if not,please change the

motor wire red and black), release the button until the door has reached the desired position. (You

also can press CLOSE to move the door close, OPENand CLOSE can be used to fine adjust the

door position.)

3. Press the SETto confirm the open position, now number 2is indicated on the LED display.

4. Press and hold CLOSE to set close position, release the button until the door has reached the

desired position. (You also can press OPEN to move the door open,OPENand CLOSE can be used

to fine adjust the door position.)

5. Press the SETto confirm the close position.

6. The door will do a complete open and close cycle.

CODE

OPEN

SET SET

OPEN

CODE

SET

OPEN

CODE

CLOSECLOSE

CODE

OPEN

SETSET

OPEN

CODE

Fig.13

Automatic close (0~90 seconds adjustable)

1. Press and hold OPENuntil is indicated on the LED display.

2. Press OPENto increase the auto close time, press CLOSE to decrease time.

3. Set timer to 0, the automatic close function will disable.

4. Press SETto confirm the setting.

5. Add 10 second per number

NOTE: Automatic close function is available only when the doorisin fully opened position.

SET CODECODE

SETSET CODE

OPEN OPEN OPEN

CLOSE CLOSE CLOSE

Setting obstruction force

Table of contents

Other Phoenix Doors Gate Opener manuals

Phoenix Doors

Phoenix Doors Enviro 6 User manual

Popular Gate Opener manuals by other brands

Elite

Elite CSW200UL instruction manual

CAME

CAME FROG-PM4 installation manual

SOMFY

SOMFY FX230 installation manual

Aprimatic

Aprimatic ONDA 500 installation instructions

Turnstiles

Turnstiles FSW 900 manual

Erreka

Erreka BUL BL33 Quick installation and programming guide

Erreka

Erreka VULCAN S manual

Beninca

Beninca R1-2 WBV quick start guide

Erreka

Erreka VULCAN D user manual

Motorline professional

Motorline professional FORT User& installer's manual

Beninca

Beninca BOB5024 manual

AGA

AGA GATEMASTER 900 HD installation manual

Chamberlain

Chamberlain MotorLift HC280ML Mechanical installation

SOMFY

SOMFY Dexxo RTS Pro INSTALLATION INSTRUCTIONS-ILLUSTRATIONS

Cardin

Cardin BL Series manual

Westfalia

Westfalia 85 27 06 instruction manual

CAME

CAME F500 installation manual

Extel

Extel VERA quick guide