Philips TSU6000 User manual
User Guide
1
Taking a First Look 2
Intelligent Remote Control 2
Before You Start 4
Getting Started 6
Activating the Remote Control 6
Defining the Brands of Your Devices 7
Working with the Home Panel 13
Operating a Device 15
Adjusting the Settings 18
Getting the Maximum out of it 22
Introduction 22
Redefining Brands 24
Learning Commands 25
Labeling Elements 29
Adding and Moving 31
Deleting and Restoring 32
Recording Macros and Setting Timers 35
Using the Remote Control with Radio Frequency 39
ProntoPro Edit 44
Troubleshooting 46
General Problems 46
Programming Problems 47
Recharging Problems 48
FAQ 49
Maintaining the Remote Control 51
Important notices 51
Cleaning the Remote Control 51
Overview of Symbols 52
Specifications 55
Index 56
Table of Contents
User Guide
2
Intelligent Remote Control
The Intelligent Remote Control can be used for most devices that
understand infrared (IR) remote control signals. Its easy-to-use
touch screen with 256 colors and its intuitive interface makes it a
perfect remote control for every user.
The Remote Control (RC) is completely customizable. In the
memory of the Remote Control, RC codes are stored to activate
different brands for all kinds of video and audio devices. The
Remote Control is set up by default to operate with Philips or
Marantz devices. When you have other brands, you simply define
the brands of your devices when you use the Remote Control for
the first time.
The Remote Control can also learn RC codes from existing remote
controls. It is designed to add devices and functions, relabel
buttons, record macros and set timers. With the ProntoPro Edit
software you create your own control panels and define your
personal look.
If you want to operate devices from a distance or from an adjacent
room, you can use the Remote Control with radio frequency (RF)
signals and an RF Extender.
The Appliance
Direct-access
buttons
Sending eye
256 color LCD
touch screen
Learning eye
Connection to the
docking station
Contrast dial
Page Up button
Serial port
Taking a First Look
Page Down button
Action buttons
Backlight button
Reset
button
Battery
compartment
Battery
cover
Latch
User Guide
3
Taking a First Look
Remote Control icon:
• Tap to enter the Mode menu and
customize the Remote Control
• Touch and hold to enter
Setup mode
Macro tab:
To activate the
Macro menu
Device tab:
To activate
the Device menu
Panel number:
Shows active
control panel
The Touch Screen
Control panel:
To send
commands
to devices
The Docking Station
The docking station is used:
• to charge the Remote Control;
• to connect your Remote Control to your computer.
The serial port on the docking station can be used as an alternative for the
serial port on the Remote Control.
Charging LED Adapter connectorSerial port
Connection for the
Remote Control
User Guide
4
Before You Start
When you use the Remote Control for the first time, you will have to:
• install the battery pack;
• place the Remote Control in the docking station and charge the Remote
Control.
Warning Use the docking station only with the Philips NiMH rechargeable battery pack.
We strongly advise you not to plug other appliances (like mobile phones,
PDA’s, …) into the docking station. This causes damage to the connector and
the appliance.
Installing the Battery Pack
1 Press the latch on the battery cover and remove the battery cover from
the Remote Control.
2 Place the battery pack in the battery compartment.
3 Plug the cable of the battery pack in the connector as illustrated.
Taking a First Look
User Guide
5
4 Place the battery cover back on.
Note Make sure the cable of the battery pack does not get stuck between the
mould and the battery cover.
After a few seconds, the Remote Control starts up automatically and an
Introduction screen appears. The Remote Control beeps twice to indicate that
it has finished starting up.
Because the battery pack of the Remote Control is not fully pre-charged, you
will have to charge it as described below.
Charging the Remote Control
For charging the Remote Control you use the docking station.
1 Plug the power adapter into a wall outlet and connect it to the docking
station.
2 Place the Remote Control in the docking station.
Make sure you hold the Remote
Control at an angle of 30° to 45°
when you place the it in the
docking station.
Charging starts immediately. The green charging LED on the front of the
docking station indicates charging takes place. When the Remote Control is
fully charged, the LED goes off.
Note Normal charging time is 2 to 3 hours, depending on the condition of the
battery pack.
You can operate the Remote Control while it is being charged.
The battery pack does not have to be entirely empty before recharging.
You can place the Remote Control in the docking station at any time.
When the battery pack is running low, the Low Battery icon flashes on the
Remote Control icon . Recharge the Remote Control as soon as possible to
ensure perfect performance.
Note The Remote Control retains all settings when the battery pack has run out.
You will only have to set the clock. See “Adjusting the Settings” on page 18.
Taking a First Look
30° to 45°
User Guide
6
Activating the Remote Control
Turning on the Display and the Backlight
The Remote Control’s display can be activated in three different ways:
Tap the screen gently with your finger or a blunt, soft object like a
pencil eraser.
The display is activated.
Tilt the Remote Control more than
50 degrees as illustrated.
The display and the backlight of the
direct-access buttons are activated.
Note In the settings (p. 18) you can choose to deactivate the Pick Up sensor.
Press the backlight button on the left side.
The display and the backlight of the direct-access buttons are activated.
When you turn on the display you see the Home panel. If another panel is
displayed, tap the Home button .
Note If the screen stays black or becomes blank, adjust the contrast using the contrast
dial on the left side.
The Remote Control has a switch-off feature: it automatically turns off to save
power.
In the settings (p. 18) you can define the switch-off time for the touch screen.
Activating Modes
The Remote Control has different modes. In Use mode the Remote Control icon
is entirely visible. If a label (like or ) covers the icon, see
page 23 to switch your Remote Control to Use mode.
Getting Started
50°
User Guide
7
Defining the Brands
of Your Devices
The Remote Control uses RC codes to activate devices. Because there are several
brands using specific RC codes, you have to define the brands of your devices.
On the Home panel you find buttons for most common video and audio devices.
When you select a device on the Home panel for the first time, you will notice that
the Remote Control is set up by default to operate Philips or Marantz devices. For
all devices other than Philips or Marantz, you will have to define the brand before
you can operate them with the Remote Control.
1 Select a device on the Home panel.
The following screen appears.
2 When the brand of your device is Philips or Marantz, click No.
The Remote Control switches to Use mode. To operate the device in Use
mode, see p. 15.
-or-
When you want to adjust the Remote
Control to operate with your brand,
click Yes.
The Remote Control switches to Brand mode.
Follow the instructions as described below.
There are three possible scenarios for defining
brands:
• You can select the brand and the code set
of your device.
• You can select the brand of your device and
search the code set.
• You can search the brand of your device.
Getting Started
User Guide
8
Selecting Brands and Code Sets
A list of brands and their corresponding RC codes are stored in the Remote
Control’s memory.
You have to select your brand from the list. Because not every device of a certain
brand uses the same RC codes, you might also have to select a set of RC codes for
your brand.
1 Tap Next.
A scrollable list of brands for the selected
device and a “virtual auto-zooming”
mini-keyboard appears.
2 Navigate through the list of brands using the scroll buttons and
to scroll up or down in the list of brands.
• By tapping the scroll buttons, you scroll through the brands one by one.
• By holding down the scroll buttons, the scrolling speed increases.
-or-
Navigate through the list of brands using the mini-keyboard to jump
through the list of brands.
• To enter a character, tap the keyboard near the character you want to use.
The keyboard is zoomed in, allowing you to tap exactly the character you
need.
After you have tapped the character, the keyboard is zoomed out. Repeat
this action for every character.
Note You can zoom out again without tapping a character by pressing the right
action button (labeled Zoom).
Getting Started
User Guide
9
• To delete a character, press the right action button (labeled
Del
).
• To enter a space, tap the lower left corner of the keyboard. When the
keyboard is zoomed in, tap the empty key.
Every time you enter a character the list displays the brands that match
the character(s). The Remote Control makes a pre-selection of the (first)
matching brand. You only have to type as many characters as needed to
display your brand.
Note When your brand is not displayed in the list of brands, you can use Search
mode. See “Searching Brands and Code Sets” on p. 12.
3 Select your brand in the list.
The selected brand is highlighted.
The Search button switches into Next.
4 Tap Next.
When your brand uses only one set of RC codes,
the Remote Control switches to Try mode.
Continue with step 5.
When there are several code sets for your brand,
a list of code sets for the selected brand appears.
Getting Started
User Guide
10
You can select the code set for your device:
Note The RC code sets are ranked. The first code set in the list is used for most
devices of the selected brand.
1 Select a code set from the list.
The selected code set is highlighted.
The Search button switches to Next.
2 Tap Next.
The Remote Control switches to Try mode. Continue with step 5.
-or-
When you do not know which code set to select for your device, you can
search the code set in Remote Control’s memory:
1 Tap Search.
The Remote Control automatically searches through all available RC code
sets to find the matching codes for your device.
2 Tap Next to start sending appropriate
commands for the selected device.
The progress bar indicates how many of the
available code sets have been tried out.
Getting Started
Other manuals for TSU6000
3
Table of contents
Other Philips Remote Control manuals
Philips
Philips SRP620/10 User manual
Philips
Philips SBCRU125/00 User manual
Philips
Philips RU125 User manual
Philips
Philips SRP9232D/27 User manual
Philips
Philips SRP4004/86 User manual
Philips
Philips SBCRU631/00 User manual
Philips
Philips SRU2103S/27 User manual
Philips
Philips Pronto SBCRU930 User manual
Philips
Philips TSU200099 User manual
Philips
Philips PRONTO TSU7500 User manual
Philips
Philips SBCRU120 User manual
Philips
Philips SBCRU111/00 User manual
Philips
Philips SRP5016 User manual
Philips
Philips SBCRU410 User manual
Philips
Philips SBCRP420/00 User manual
Philips
Philips SRC3036/27 Installation and operation manual
Philips
Philips SRP5004 User manual
Philips
Philips SBCRU130 User manual
Philips
Philips SRU 4010/10 User manual
Philips
Philips Perfect replacement SRP5107WM/17 User manual
