Philips BT110 User manual
BT110
Register your product and get support at
www.philips.com/support
User manual
1EN
Contents
1 Important 2
2 Your portable speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Attach the string 5
Charge the built-in battery 5
Turn on/o 5
4 Play from Bluetooth devices 6
Connect a device 6
Disconnect a device 7
Reconnect a device 7
Connect another device 7
5 Play from external devices 8
6 Product information 9
Audio 9
Speaker 9
Bluetooth 9
General information 9
7 Troubleshooting 10
General 10
About Bluetooth device 10
8 Notice 11
Compliance 11
Care of the environment 11
Trademark notice 12
2EN
1 Important
Warning
•Never remove the casing of this product.
•Never place this product on other electrical
equipment.
•Keep this product away from direct
sunlight, naked ames or heat.
• Read these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not install near any heat
sources such as radiators, heat
registers, stoves, or other apparatus
(including ampliers) that produce
heat.
• Only use attachments/accessories
specied by the manufacturer.
• The battery shall not be exposed
to excessive heat such as sunshine,
re or the like.
• Do not place any sources of danger
on the apparatus (e.g. lighted
candles).
• The operation temperature of the
product is from -10 °C to 40 °C.
• The product supports USB V2.0 or
V1.1 only.
Note
•The type plate is located on the bottom of
the apparatus.
3EN
2 Your portable
speaker
Congratulations on your purchase,
and welcome to Philips! To fully
benet from the support that Philips
oers, register your product at
www.philips.com/welcome.
Introduction
With this speaker, you can enjoy audio
from Bluetooth-enabled devices or
other external devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• String for carrying
• Printed materials
4EN
Overview of the speaker
a
• Press and hold for two seconds
to enter Bluetooth pairing mode.
• Press and hold for two seconds
to disconnect Bluetooth
connection.
• Press to answer an incoming
call.
• Press and hold for two seconds
to reject an incoming call.
• During a call, press to end the
current call.
• During a call, press and hold for
two seconds to transfer the call
between your mobile device and
the speaker.
b
• Turn the speaker on or o.
c LED indicator
• Indicate battery or Bluetooth
connection status.
a
d
e
b
c
d AUDIO IN
• Connect an external audio
device.
e DC IN
• Recharge the built-in battery.
5EN
3 Get started
Always follow the instructions in this
chapter in sequence.
Attach the string
For easy carrying, attach the supplied
string to this speaker as illustrated.
Charge the built-in
battery
The speaker is powered by a built-in
rechargeable battery.
Note
•Before use, fully charge the built-in battery.
•The micro USB socket is for charging only.
•It takes you approximately four hours to
fully charge the battery.
•Rechargeable battery has a limited number
of charge cycles. Battery life and number of
charge cycles vary by use and settings.
Connect the USB cable between
• the DC IN socket on the speaker,
and
• a USB socket on a computer.
The LED indicator indicates the battery
status.
Battery Status LED Indicator
Under
charging
Red
Fully charged/
Not charging
O (in power-o
mode);
Blue (in Bluetooth
mode)
Low battery Flashing red
Turn on/o
Press and hold for three seconds to
turn the speaker on or o.
» When the speaker is turned on,
the LED indicator begins to ash.
» When the speaker is turned o,
the LED indicator lights o.
Note
•When there is no operation and audio
output for 15 minutes, the speaker switches
to standby mode automatically.
6EN
4 Play from
Bluetooth
devices
With this speaker, you can listen to
audio from Bluetooth-enabled devices.
Connect a device
Note
•The speaker can memorize a maximum of
four paired devices. The fth paired device
will replace the rst one.
•Any obstacle between this speaker
and a Bluetooth device can reduce the
operational range.
•Keep away from any other electronic
device that may cause interference.
•The operational range between this
speaker and a Bluetooth device is
approximately 10 meters (30 feet).
•Make sure that there is no audio input
cable connected to the AUDIO IN socket.
1 Make sure that the speaker is in
Bluetooth pairing mode
• For rst-time use, the
speaker enters pairing mode
automatically.
• If the speaker has been paired
with other device before, press
and hold on the speaker for
two seconds to enter pairing
mode.
» The LED indicator ashes blue
quickly.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices that can be paired (refer to
the user manual of the device).
3 Select [Philips BT110] displayed
on your device for pairing and
connection. If necessary, input
“0000” as the pairing password.
» After successful pairing and
connection, the speaker beeps
twice, and the LED indicator
turns solid blue.
LED indicator (blue)
Indicator Bluetooth Connection
Status
Quick ashing
(2Hz)
Pairing
Slow ashing
(1Hz)
Connecting
Solid blue Connected
2 sec
.
Philips BT110
7EN
Play from a Bluetooth-enabled
device
Note
•If there is an incoming call on the
connected mobile phone, music play
pauses.
After successful Bluetooth connection,
play music on the connected Bluetooth
device.
» Music streams from your
Bluetooth device to the speaker.
Tip
•You can use your Bluetooth device to
control play.
Control your phone call
After Bluetooth connection, you can
control an incoming call with this
speaker.
Button Function
Press to answer an incoming
call.
Press and hold for two
seconds to reject an incoming
call.
During a call, press to end the
current call.
During a call, press and hold
for two seconds to transfer
the call between your mobile
device and the speaker.
Note
•Music play pauses when there is an
incoming call, and resumes when your
phone call ends.
Disconnect a device
• Press and hold for two seconds;
• Turn o the speaker;
• Disable Bluetooth on your device;
or
• Move the device beyond the
communication range.
Reconnect a device
• When you turn on the speaker, it
will reconnect the last connected
device automatically;
• If not, select [Philips BT110] on
your Bluetooth menu to start
reconnection.
Connect another device
1 Press and hold for two seconds to
disconnect the currently connected
device;
» The speaker enters Bluetooth
pairing mode.
2 Connect another Bluetooth device.
8EN
5 Play from
external devices
With this speaker, you can also listen
to an external audio device such as an
MP3 player.
Note
•Make sure that music playback through
Bluetooth is stopped.
1 Connect an audio input cable (not
supplied) with a 3.5 mm connector
on both ends to
• the AUDIO IN socket on this
speaker, and
• the headphone socket on the
external device.
2 Play audio on the external device
(refer to its user manual).
» The speaker switches to the
AUDIO IN mode.
Tip
•When you start music streaming from
a connected Bluetooth device, the
speaker switches to the Bluetooth source
automatically.
Table of contents
Other Philips Portable Speakers manuals
Philips
Philips BT4000 User manual
Philips
Philips SBA3210/00 User manual
Philips
Philips SBA3010/85 User manual
Philips
Philips SBA290/05 User manual
Philips
Philips BT100 User manual
Philips
Philips BT55 User manual
Philips
Philips SBA3000 User manual
Philips
Philips BT3500 Product information sheet
Philips
Philips SBT11BLK User manual
Philips
Philips SBCBA109 User manual
Philips
Philips ShoqBox SB300 User manual
Philips
Philips sbm130 User manual
Philips
Philips SBA3010BLU/37 User manual
Philips
Philips AEM120BLU User manual
Philips
Philips SB2000 User manual
Philips
Philips SBA1610/00 User manual
Philips
Philips AT11/94 User manual
Philips
Philips SBA1500 User manual
Philips
Philips SBA3000/00 User manual
Philips
Philips BT50B/37 User manual
