Philips Symmetry Series Assembly instructions

Philips Lighting North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873, USA

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Canada Ltd.

281 Hillmount Road,

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140053520 February 2016

Symmetry Unit Equipment

6 and 12 Volt

18 to 72 Watt

120/100V 50/60Hz

Service Questions Call: 910-259-1000

INSTALLATION AND

OPERATING

INSTRUCTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety

precautions should always be followed, including

the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

All servicing should be performed by qualified

personnel only.

Equipment should be mounted in locations and at

heights where it will not be readily subjected to

tampering by unauthorized personnel.

The use of accessory equipment not recommended

by the manufacturer may cause an unsafe condition.

Do not use this equipment for other than intended

use.

Do not let supply cords touch hot surfaces.

Do not mount near gas or electric heaters.

Caution: Halogen cycle lamp(s) are used in this

equipment. To avoid shattering: Do not operate

lamp in excess of rated voltage, protect lamp

against abrasion and scratches and against liquids

when lamp is operating, dispose of lamp with care.

Halogen cycle lamps operate at high temperatures.

Do not store or place flammable materials near

lamp.

Use caution when servicing batteries. Battery acid

can cause burns to skin and eyes. If acid is spilled

on skin or eyes, flush acid with fresh water and

contact a physician immediately.

CAUTION: To avoid electrical overload, total

connected lamp load (factory and field installed)

should not exceed output rating.

SAVE THESE

INSTRUCTIONS

GENERAL INSTRUCTIONS

WARNING –Shut off AC power to branch

circuits to which units will be connected. All

wiring should be per N.E.C. Articles 501-4(b)

and local codes.

To maintain warranty, equipment with batteries

must be installed or placed on charge within

prescribed period after shipment.

Philips Lighting North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873, USA

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Canada Ltd.

281 Hillmount Road,

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140053520 February 2016

Figure 1

STEP 1 (see figure 1)

Expose junction box mounting pattern by loosening velcro strap over battery or batteries

and removing them from the housing (leave velcro strap in the housing). A quick disconnect is

provided between the electronics and batteries. Be certain that this quick disconnect is

disconnected before attempting to remove batteries. If it is planned to use toggle bolts to mount

unit to wall, additional knockouts intended for this purpose can be found under the lenses. These

keyhole slots will accommodate #6 toggle bolts. Refer to the sketch above for instructions on

removing the lenses.

Figure 2

STEP 2 (see figure 2)

Locate 4 pole connector attached to transformer inside unit. Remove 6” long extension

cable and wire to AC supply as shown. Unused black or blue lead must be insulated to prevent

shorting. If your unit has battery capacity in excess of the wattage required by its internal lamp

heads, it will be provided with a 2 pole remote lamp connector as well. Remote lamp heads used

must match voltage of unit (6 or 12 volt) and the combined wattage of the internal and remote

lamp heads must not exceed the rated wattage of the equipment –refer to nameplate label for

maximum wattage. If unit is not used to power any remote heads, be certain to insulate the unused

orange and yellow leads to prevent shorting or discard the 6” orange/yellow extension cable.

Philips Lighting North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873, USA

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Canada Ltd.

281 Hillmount Road,

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140053520 February 2016

Figure 3

STEP 3 (see figure 3)

Remove desired knockouts for junction box or toggle bolt mounting. Also remove the

larger rectangular knockout for routing of AC leads unless using the conduit knockout found on

top of the housing. Mount unit to wall or ceiling using fasteners supplied with junction box or

mount to wall using toggle bolts (not provided). Pull AC and remote lamp connectors through

rectangular knockout and reconnect to matching wire harnesses as shown in step two. Reinstall

the battery and connect the battery quick disconnect. Re-secure the Velcro battery strap to secure

the battery in place. If MR-16 type lamps have been specified, they have been shipped in small

individual cartons inside the larger shipping carton. They are installed by press fitting into the

ceramic lamp base inside each lamp head. Energize AC supply branch circuit and refer to page 5

for operating instructions.

No rigid conduit –Flexible conduit only

Philips Lighting North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873, USA

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Canada Ltd.

281 Hillmount Road,

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140053520 February 2016

MAINTENANCE

LAMP HEAD AIMING –Remove lens covers as shown in step 1. Lamp heads may be aimed by

grasping them at the base and rotating them to aim at the desired location. Lamp head only rotates

approximately 135°which is enough to aim in any direction whether mounted on wall or ceiling.

AC FUSE AND AC OR DC DISCONNECT SWITCH OPTIONS –If ordered, these options can

be found under the right lamp head lens.

TAMPERPROOFING –If ordered, install this option using the included screw kit which includes

two flat head screws, two pan head screws and a tamperproof Torx T-15 bit.

Philips Lighting North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873, USA

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Canada Ltd.

281 Hillmount Road,

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140053520 February 2016

Self Diagnostic System Operation –Emergency Light or EXIT Sign Products

Normal Power Up Sequence

At power up the red and green LED indicators will alternately flash for one to two seconds. Next the product will execute a

“Power Up Quick Test” causing the green LED indicator to flash rapidly. If any faults are detected during the “Power Up Quick

Test” these will be evident by a flashing red LED indicator. If the audible diagnostic option has been ordered, the flashing red

LED will be accompanied by a simultaneous beeping tone. (Note: A continuous rapid alternating Red/Green flash with rapid

beeping tone indicates incorrect voltage applied to input lead. TURN OFF POWER IMMEDIATELY!)

Emergency Operation

Emergency operation occurs when AC power fails. The product remains in emergency operation until AC power is restored or

battery capacity is depleted. During emergency operation both red and green LED indicators are disabled.

User Interface

Green LED indicator

Slow Flash/Continuous ON = AC power present; normal operating condition

Rapid Flash = product performing an automatic or manually initiated diagnostic test

Red LED indicator

Single Flash = battery fault

Two Flashes = lamp failure (light bar failure –EXIT signs)

Three Flashes = charger fault

Four Flashes = transfer fault

(If more than one fault condition is present simultaneously, the red LED will flash the indication pattern for each fault

independently then repeat the cycle.)

Pushbutton Test Switch

Long Press (longer than 0.5sec) transfers product to emergency operation during time the button is pressed.

Short Press initiates self diagnostic activities as follows:

One Press cancels diagnostic test presently running.

Two Presses starts a one minute diagnostic test.

Three Presses starts a 90 minute diagnostic test.

Four Presses conducts a lamp load calibration (emergency light products only).

Seven Presses initiates a system reset.

(Note: the microprocessor will allow up to seven, one minute diagnostic tests within the first 24 hours of

operation. Allow 24 hours of charging before performing any long duration testing.)

Buzzer (optional)–Sounds in unison with the flashing red LED if a fault condition is present. Buzzer may be silenced for

up to 196 hours by a short press of either the test switch or the optional IR remote control device “silence” button.

Correcting fault condition will cancel fault notification. Lamp failure indication requires a manually activated diagnostic

test after lamp replacement to cancel notification.

IR Remote Control (optional)- is a hand held device that allows remote activation of diagnostic testing and silencing of

the optional buzzer during fault conditions.

Philips Lighting North America Corporation

200 Franklin Square Drive

Somerset, NJ 08873, USA

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Canada Ltd.

281 Hillmount Road,

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140053520 February 2016

This manual suits for next models

Table of contents

Other Philips Outdoor Light manuals

Philips

Philips 69069/**/16 User manual

Philips

Philips 163384716 User manual

Philips

Philips Ecomoods 16905/87/16 User manual

Philips

Philips ecoMOODS 16915/93/16 User manual

Philips

Philips ecoMOODS 16917/31/16 User manual

Philips

Philips Ledino 16807/87/16 User manual

Philips

Philips Ledino 168183116 User manual

Philips

Philips ecoMOODS 16914/93/16 User manual

Philips

Philips Ledino 168018716 User manual

Philips

Philips 163404716 User manual

Philips

Philips Ecomoods 16909/93/16 User manual

Philips

Philips ecoMOODS 16907/87/16 User manual

Philips

Philips Ecomoods 16904/87/16 User manual

Philips

Philips 168244716 User manual

Philips

Philips 172298816 User manual

Philips

Philips 168094716 User manual

Philips

Philips 172399316 User manual

Philips

Philips ecoMOODS 16916/93/16 User manual

Philips

Philips ColorGraze Powercore MX User manual

Philips

Philips 15385/**/16 User manual

Philips

Philips 163394716 User manual

Philips

Philips SV16 Series User manual

Philips

Philips 168089316 User manual

Philips

Philips hue Lily base unit User manual

Popular Outdoor Light manuals by other brands

Sealey

Sealey LED37 instructions

nordlux

nordlux VEJERS Mounting instruction

SImx

SImx ELITE LED LHTC637 installation instructions

GEV

GEV CAROLINE 10833 manual

NEBO

NEBO NEB-LSP-0020 Use and care guide

WE-EF

WE-EF PFL540 LED Installation and maintenance instructions

Lindby

Lindby 9949029 Intended use

HEPER

HEPER DOGO Side LW6048.585-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Maretti

Maretti VIBE S 14.6080.04.A quick start guide

BEGA

BEGA 84 253 Installation and technical information

HEPER

HEPER MINIMO Installation & maintenance instructions

LIGMAN

LIGMAN BAMBOO 3 installation manual

Maretti

Maretti TUBE CUBE WALL 14.4998.04 quick start guide

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB installation instructions

urban ambiance

urban ambiance UQL1273 installation instructions

TotalPond

TotalPond 52238 instruction manual

Donner & Blitzen

Donner & Blitzen 0-02661479-2 owner's manual