Philips bodine LP400 User manual
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
SAVE THESE INSTRUCTIONS
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
© Philips Emergency Lighting
A Division of Philips Electronics North America Corporation
236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine
70100194
Installation Instructions
1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter
connector must be open. Do not join inverter connector until installation is complete and AC power is
supplied to the emergency ballast.
2. This product is for use with one (4') 32 W T8 bipin uorescent lamp.
3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and
inverter connector of the emergency ballast before servicing.
5. This emergency ballast is for factory or eld installation in the ballast channel or on top of xture.
6. This product is for use in indoor xtures except air handling heated air outlets, and wet, damp, or
hazardous locations.
7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not eld
replaceable. Contact the manufacturer for information on service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualied service personnel.
CAUTION: Verify that all replacement lamp types marked on the installed luminaire are also identied as suit-
able for use with this inverter/charger pack.
LP400
Ni - Cd
08/01/13
EMERGENCY LIGHTING EQUIPMENT
STEP #1 INSTALLING THE EMERGENCY BALLAST
> Disconnect AC power from the xture. Remove the
ballast channel cover and install the emergency
ballast in the ballast channel (see Illustration 1).
> Remote mounting distance must be less than half
the maximum remote mounting distance for the
AC ballast. Consult AC ballast manufacturer
before remote installation.
STEP #2 INSTALLING THE TEST SWITCH
> Refer to Illustration 2 and install the test switch
through the ballast channel cover of a troffer or
through the side of a strip xture.
> Drill a 1/2" hole and install the switch as shown.
> Wire the test switch so that it removes AC power
from both the emergency ballast and the AC ballast
at the same time (see Illustration 3).
STEP #3 INSTALLING THE CHARGING
INDICATOR LIGHT
> Refer to Illustration 3A or 3B and install the charg-
ing indicator light so that it will be visible after the
xture is installed.
WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT
LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN
INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED
TO THE EMERGENCY BALLAST.
NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched
source of power is required. The emergency ballast must be fed from the same
branch circuit as the AC ballast.
ILLUSTRATION 1
ILLUSTRATION 2
INSTALLATION
UNSWITCHED FIXTURE SWITCHED FIXTURE UNSWITCHED FIXTURE SWITCHED FIXTURE
SINGLE POLE DOUBLE POLE OPTION
BLACK 120V
OR
ORANGE 277V
BLACK AC
BALLAST
EMERGENCY
BALLAST
WHITE
WHITE
HOT
COM (CAP UNUSED LEAD)
SINGLE POLE
TEST SWITCH
(Breaking the Hot)
BLACK 120V
OR
ORANGE 277V
BLACK
EMERGENCY
BALLAST
WHITE
WHITE
HOT
COM
(CAP UNUSED LEAD)
SINGLE POLE
TEST SWITCH
(Breaking the Common)
BLACK 120V
OR
ORANGE 277V
BLACK
EMERGENCY
BALLAST
WHITE
WHITE
HOT
COM (CAP UNUSED LEAD)
SINGLE POLE
TEST SWITCH
(Breaking the Hot)
BLACK 120V
OR
ORANGE 277V
BLACK
EMERGENCY
BALLAST
WHITE
WHITE
HOT
COM
(CAP UNUSED LEAD)
SINGLE POLE
TEST SWITCH
(Breaking the Common)
WALL
SWITCH
WALL
SWITCH
AC
BALLAST
AC
BALLAST
AC
BALLAST
BLACK 120V
OR
ORANGE 277V
BLACK AC
BALLAST
EMERGENCY
BALLAST
WHITE
WHITE
BLK
HOT
COM
RED RED
(CAP UNUSED LEAD)
BLK WALL
SWITCH
BLACK 120V
OR
ORANGE 277V
BLACK AC
BALLAST
EMERGENCY
BALLAST
WHITE
WHITE
BLK
HOT
COM
RED RED
(CAP UNUSED LEAD)
DOUBLE POLE
TEST SWITCH
BLK
DOUBLE POLE
TEST SWITCH
ILLUSTRATION 3
2
Fixture
Test Button
Hex Nut
Hex Nut
Test Switch
Leads
Push to Test
STEP #4 WIRING THE EMERGENCY BALLAST
> Select the appropriate wiring diagram and connect the emergency ballast to the AC ballast and lamp(s). Make
sure all connections are in accordance with the National Electrical Code and any local regulations.
> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.
> At this point, power should be connected to both the AC ballast and the emergency ballast, and the Charging
Indicator Light should illuminate indicating the battery is charging.
> A short-term discharge test may be conducted after the emergency ballast has been charging for one hour.
Charge for 24 hours before conducting a long-term discharge test. Refer to OPERATION.
> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection PointTo
Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency Power
Supplies Before Servicing."
When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When
power fails, the emergency ballast automatically switches to emergency power, operating one lamp at reduced illumination.
This emergency ballast will operate one (4') 32 W T8 bipin lamp for a minimum of 90 minutes.
Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to
ensure that it is working. The following schedule is recommended:
1. Visually inspect the charging indicator light monthly. It should be illuminated.
2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds.
One lamp should operate at reduced illumination.
3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced
illumination for at least 90 minutes.
! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !
MAINTENANCE
OPERATION
NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label. If a
detached charging indicator light is used, connect by matching wire colors and install as shown above.
STEP 2STEP 1
ILLUSTRATION 3B
ILLUSTRATION 3A
3
Charging
Indicator
Light
1/2" White
Bushing
Violet (+)
Brown (–)
Violet (+)
Brown (–)
1/2" White
Bushing
5/8" Black
Bushing 5/8" Black
Bushing
1/2" Punch
Fixture Fixture
Charging
Indicator
Light
WIRING DIAGRAM for EMERGENCYONLY xtures
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.
WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION
4
FIG D TWO (2) LAMP RAPID START BALLAST
FIG C TWO (2) LAMP INSTANT START BALLAST
FIG F THREE (3) LAMP RAPID START BALLAST
FIG G FOUR (4) LAMP INSTANT START BALLAST FIG H FOUR (4) LAMP RAPID START BALLAST
FIG E THREE (3) LAMP INSTANT START BALLAST
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
( )
EMERGENCY
LAMP 1
LAMP 2
BLACK
WHITE
YELLOW
YELLOW
LINE
RED
RED
BLUE
BLUE
AC
BALLAST
BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP 1
LAMP 2
LAMP 3
BLACK
WHITE
LINE
RED
BLUE
BLUE BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
AC
BALLAST BLUE
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP 1
LAMP 2
LAMP 3( )
EMERGENCY
BLACK
WHITE
YELLOW
YELLOW
LINE
RED
RED
BLUE/WHT
BLUE/WHT
BLUE
BLUE BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
AC
BALLAST
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP 1
LAMP 2
LAMP 3
LAMP 4( )
EMERGENCY
BLACK
WHITE
YELLOW
YELLOW
LINE
RED
RED
BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
AC
BALLAST
BLUE
BLUE
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP 1
LAMP 2
LAMP 3
LAMP 4
BLACK
WHITE
YELLOW
YELLOW
BROWN
BROWN
LINE RED
RED
BLUE/WHT
BLUE/WHT
BLUE
BLUE
BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
AC
BALLAST
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP 1
LAMP 2 (EMERGENCY)
BLACK
WHITE
LINE BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
AC
BALLAST RED
BLUE
BLUE
FIG B ONE (1) LAMP RAPID START BALLAST
FIG A ONE (1) LAMP INSTANT START BALLAST
FIG I ONE (1) 17-215 W LAMP WITHOUT AC BALLAST
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP
BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
CAP
CAP
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
LAMP
BLACK
WHITE
RED
LINE BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
AC
BALLAST
BLUE
INVERTER
CONNECTOR
RED WHITE
ORANGE
BLACK
WHITE
VIOLET
BROWN
277 V
120 V
COM
CHARGING
INDICATOR
LIGHT
TO UNSWITCHED AC
USE PROPER TAP
CAP UNUSED LEAD
EMERGENCY
BALLAST
BLACK
WHITE
LINE
RED
RED
BLUE
BLUE
AC
BALLAST
LAMP
BLUE
BLUE/WHT
YELL/BLK
YELLOW
RED
Table of contents
Other Philips Lighting Equipment manuals
Philips
Philips CR434B User manual
Philips
Philips Leko Lite 11430C Troubleshooting guide
Philips
Philips BN131C LED SWT/SCCT L600 PSU Slim User guide
Philips
Philips hue Adore User manual
Philips
Philips SP160P LED40S 840 W60L60 PSU SI User guide
Philips
Philips Disney Softpal Sulley User manual
Philips
Philips Hadco BUL16 MICRO BULLYTE User manual
Philips
Philips LED Luminaires User manual
Philips
Philips Showline SL eSTROBE 130 User manual
Philips
Philips Lightstrip Plus 71901 Series User manual
Philips
Philips Selecon Accent LED Beamshaper User manual
Philips
Philips 32158-31-16 User manual
Philips
Philips hue Centris User manual
Philips
Philips 56452-17-16 User manual
Philips
Philips hue User manual
Philips
Philips BVP528 User manual
Philips
Philips 32146-48-16 User manual
Philips
Philips BVP525 HGB User manual
Philips
Philips 56430-31-16 User manual
Philips
Philips Selecon PL1 Series Instruction Manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
