Philips QC5090 User manual
QC5090, QC5070
2
3
1
4
QC5090, QC5070
ENGLISH 6
DANSK 13
DEUTSCH 20
27
ESPAÑOL 35
SUOMI 42
FRANÇAIS 48
ITALIANO 55
NEDERLANDS 62
NORSK 69
PORTUGUÊS 76
SVENSKA 83
TÜRKÇE 90
6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
This super-easy Philips hair clipper adapts to the contours of the head
and enables comfortable use.
General description (Fig. 1)
ALarge comb
BSmall comb
CPrecision trimmer (QC5090 only)
DCutting unit
EOn/off slide
FResult indicator (indicates the hair length after cutting)
GLength lock (locks the hair length setting)
HCleaning brush
IAdapter
JAppliance plug
KScissors
LStyling comb
Important
Read this user manual carefully before you use the appliance and save it
for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- Check if the voltage indicated on the adapter and on the appliance
corresponds to the local mains voltage before you connect the
appliance.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
ENGLISH
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that they do not play with
the appliance.
Caution
- Do not immerse the appliance in water or any other liquid, nor rinse
it under the tap.
- Use, charge and store the appliance at a temperature between 15°C
and 35°C.
- Do not charge the appliance in a pouch or cassette.
- Only use the adapter supplied.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- Do not use the appliance when one of the attachments is damaged
or broken, as this may cause injury.
- This appliance is only intended for clipping human scalp hair. Do not
use it for another purpose.
This Philips appliance complies with all standards regarding
electromagnetic elds (EMF). If handled properly and according to the
instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.
General
The adapter transforms 220-240 volts to a safe low voltage of less than
24 volts.
Preparing for use
Charging
Charge the appliance for at least 8 hours (NiCd battery) or 12 hours
(NiMh battery) before you use it for the rst time and after a long period
of disuse.
A fully charged appliance has a cordless clipping time of up to 35 minutes
(NiCd battery) or 50 minutes (NiMh battery).
ENGLISH 7
Do not charge the appliance for more than 24 hours.
1 Switch off the appliance.
2 Insert the appliance plug into the appliance and put the adapter in
the wall socket (Fig. 2).
,The charging light goes on to indicate that the appliance is
charging (Fig. 3).
The charging light does not change colour and does not go out when
the appliance is fully charged.
Optimising the lifetime of the rechargeable battery
- After you have charged the appliance for the rst time, do not
recharge it between clipping sessions. Continue using it and recharge
it only when the battery is (almost) empty.
- Discharge the battery completely twice a year by letting the motor
run until it stops.
- Do not keep the appliance plugged in continuously.
- If you have not used the appliance for a long time, recharge it for 8
hours (NiCd battery) or 12 hours (NiMh battery).
Corded clipping
When the rechargeable battery is empty, you can also run the appliance
from the mains.
Do not run the appliance from the mains when the battery is fully
charged.
To use the hair clipper from the mains:
1 Switch off the appliance and connect it to the mains.
2 Wait a few seconds and then switch on the appliance.
Using the appliance
Clipping with comb
- The hair length after cutting is indicated in millimetres on the result
indicator (Fig. 4).
ENGLISH8
- The hair length after cutting is only visible when one of the combs is
attached. Use the small comb for a hair length of 3-21mm and use
the large comb for a hair length of 23-41mm.
1 Slide the comb into the guiding grooves of the appliance
(‘click’) (Fig. 5).
Make sure that the arms of the comb have been properly slid into the
grooves on both sides.
2 Turn the length lock to set the comb to the desired hair length
setting (Fig. 6).
- The small comb cuts the hair to a length of 3mm, 6mm, 9mm, 12mm,
15mm, 18mm or 21mm.
- The large comb cuts the hair to a length of 24mm, 27mm, 30mm,
33mm, 36mm, 39mm or 42mm.
3 Switch on the appliance (Fig. 7).
Tips
- We advise you to start clipping at the highest setting of the large
comb and to reduce the hair length in small steps until you reach the
desired hair length.
- If a lot of hair has accumulated in the comb, remove the comb and
blow and/or shake the hair out of it. Removing the comb does not
change the selected hair length setting.
- Write down the hair length settings used to create a certain hairstyle
as a reminder for future clipping sessions.
Clipping without comb
You can use the clipper without comb to contour the neckline and the
area around the ears.
The comb keeps the cutting unit at a certain distance from your head.
This means that, if you use the clipper without the comb, your hair will be
cut off very close to the skin.
1 Pull the comb off the appliance (Fig. 8).
Never pull at the exible top of the comb. Always pull at the bottom
part.
ENGLISH 9
Using the precision trimmer
You can use the precision trimmer for precise contouring and dening.
1 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (Fig. 9).
Be careful that the cutting unit does not fall to the oor.
2 Place the lug of the precision trimmer in the slot and push the
unit onto the appliance (‘click’) (Fig. 10).
Cleaning
Clean the appliance every time you have used it.
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as alcohol, petrol or acetone to clean the appliance.
Only clean the appliance and the adapter with the cleaning brush
supplied.
1 Make sure the appliance is switched off and disconnected from the
mains.
2 Pull the comb off the appliance (Fig. 8).
3 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (Fig. 9).
Be careful that the cutting unit does not fall to the oor.
4 Clean the cutting unit with the cleaning brush supplied (Fig. 11).
5 Clean the inside of the appliance with the cleaning brush
supplied (Fig. 12).
6 Place the lug of the cutting unit into the slot and push the cutting
unit back onto the appliance (‘click’) (Fig. 10).
Note:This appliance does not need any lubrication.
ENGLISH10
Other manuals for QC5090
3
This manual suits for next models
1
Table of contents
Languages:
Other Philips Hair Clipper manuals
Philips
Philips HQC484/60 User manual
Philips
Philips QC5050/40 User manual
Philips
Philips HQC684/00 Manual
Philips
Philips HQC483 User manual
Philips
Philips QGC5000 User manual
Philips
Philips BRT381 User manual
Philips
Philips QC5090 User manual
Philips
Philips BT1216 User manual
Philips
Philips Norelco QC5580 User manual
Philips
Philips QC5170 User manual
Philips
Philips BT5275 User manual
Philips
Philips HC7460/13 User manual
Philips
Philips Norelco QC5130/80 User manual
Philips
Philips QGC5000 User manual
Philips
Philips Norelco QC5055 User manual
Philips
Philips HQC483 User manual
Philips
Philips HS025/45 User manual
Philips
Philips HQ-C485 User manual
Philips
Philips QC5390 User manual
Philips
Philips HQC241/20 User manual
