Philips HD 8753 User manual
All parts of this document are the property of Saeco International Group.
All rights reserved. This document and all the information herein is provided without liability deriving from any errors or omissions. Furthermore, no part may be reproduced,
used or collected, except where express authorisation has been provided in writing or through a contractual agreement.
Published by Saeco International Group Subject to modication EN 4219 400 00014
Service
Service
Service
Service
Coee Machine HD 8753 HD 8751 HD 8752
Intelia
Table of contents Page
1. Introduction
1.1. Documentation required 1
1.2. Tools and equipment required 1
1.3. Material 1
1.4. Safety warnings 1
1.5 Intelia range 2
1.6.1. External machine parts 3
1.6.2. Internal machine parts 4
2. Technical specications
2.1. Technical specications 1
2.2. Machine parameters and performance 2
3. User instructions
3.1. Intelia Cappuccino customer and programming
menu
1
3.2. Intelia Focus and Class customer and programming
menu
2
3.3. Operation, cleaning and maintenance 3
4. Operating logic
4.1. Water circuit 1
4.2. Coee cycle 3
4.3. Single microswitch 4
4.4. Temperature sensor 4
4.5. Coee grinder 5
4.6 Low bean level detection, dose quantity
adjustment, coee grinder blocked
5
2011-Sept-30
Table of contents Page
4.7. Dose self-learning (SAS) 6
4.8. Water level detection (water tank) 7
4.9. Descaling request 7
4.10. Water lter 8
4.11 Intelia Cappuccino milk carafe 8
5. Troubleshooting
5.1.1. Intelia Cappuccino test mode 1
5.1.2. Intelia Focus and Class Test mode 6
5.2. SteamOut 10
5.3. Error messages 11
6. Standard checks
6.1. Repair schedule 1
6.2. Service schedule 1
6.3. Final test 2
7. Disassembly
7.1. Intelia Cappuccino outer Shell 1
7.2. Intellia Class and Focus outer Shell 2
7.3. Coee grinder 2
7.4. Grinder blades 3
7.5. Coee grinder adjustment 4
7.6 Intelia Cappuccino three-way solenoid valve 4
7.7 Intelia Class and Focus two-way solenoid valve 5
7.8 Intelia Cappuccino carafe tting body 5
7.9 Pump 6
Service
Service
Manual
Manual
Rev. 01 September 2011
Saeco International Group Rev. 01 / September 2011 INTELIA
Table of contents Page
7.10. Flow-meter 6
7.11. Power board 6
7.12. Water sensor control board 6
7.13. Gear motor 7
7.14. Boiler 9
7.15. Dispenser assembly 9
7.16. Valve disassembly 9
7.17. Control board and display 10
7.18. Fitting and removing Oetiker clamps 11
8. Notes
9. Water circuit diagram
10 Electrical diagram
Saeco International Group Rev. 01 / September 2011 INTELIA
CHAPTER 1
INTRODUCTION
INTELIA 01 INTRODUCTION
Saeco International Group Rev. 01 / September 2011 Page / 05
1.1 Documentation required
The following documentation is needed for repair procedures:
Instruction booklet for specific model•
Technical documentation for specific model (diagrams, exploded views)•
1.2 Tools and equipment required
As well as the standard equipment, the following is required:
Qty. Description Notes
1 Screwdriver Torx T 8 - T 10 - T 20
1 Pliers for Oetiker clamps
1 CC -A - Vdc tester
1 Digital thermometer Scale limit > 150°C
1 SSC (Saeco Service Center) Programmer
(for programming and diagnostics mode)
1.3 Material
Description Notes
Thermal paste Heating element > 200°C
Descaler Saeco descaler
Grease solvent Personal choice
Silicone grease Safe to use with food
1.4 Safety warnings
We recommend you consult the technical manual of the machine before performing any mainte-
nance work.
Observe all applicable standards relating to the repair of electrical appliances.
Always disconnect the power plug from the mains before beginning repair work.
Simply turning off the main machine power switch is not an adequate safety precaution.
This domestic appliance is rated as insulation class I.
On completion of the repair work, insulation and dielectric rigidity tests must be performed.
01
INTELIA 01 INTRODUCTION
Saeco International Group Rev. 01 / September 2011 Page / 05
1.5. Intelia range
Cappuccino Class Focus
Led interface display x x x
Thermoplastic parts x x x
Milk carafe x
Cappuccino maker x
Pannarello (frother) x
Automatic dosing (SAS) x x x
Dispensed coffee memory capacity x x x
Automatic shutdown (after 30’ inactivity) x x x
Automatic descaling cycle x x x
Height adjustable dispenser x x x
Cup stand x x x
Removable dispenser x x x
Automatic descaling cycle x x x
Drip tray presence sensor x x x
02
CLASS
FOCUS
CAPPUCCINO
INTELIA 01 INTRODUCTION
Saeco International Group Rev. 01 / September 2011 Page / 05
03
1.6.1 External machine parts
Coffee bean hopper
with lid
Dreg drawer
Power cable socket and
main switch
Grinding
adjustment
Control
panel
Milk carafe
Water dispenser
(removable)
Intelia Cappuccino
Pre-ground coffee
compartment
Coffee dispenser
Brewing unit
Water tank
Drip tray release
button
Display
cappuccino button
ON/OFF button
Espresso dispensing
button
Long espresso
dispensing button
Hot water/steam
selection button MENU
button
Aroma / Pre-ground
button
Drip
tray+grille
Service
hatch
INTELIA 01 INTRODUCTION
Saeco International Group Rev. 01 / September 2011 Page / 05
04
Drip
tray+grille
Coffee bean
hopper with lid
Hot water/steam
dispensing pipe
Pannarello
(Intelia Focus)
Cappuccino valve
(Intelia Class)
Dreg drawer
Power cable socket and
main switch
Control
panel
Pre-ground coffee
compartment
Coffee
dispenser
Service hatch
Brewing unit
Water tank
Display
ON/OFF button
Espresso dispensing
button
Long espresso
dispensing button
Hot water/steam
selection button MENU button
Descaling button
Intelia Focus
Aroma / Pre-ground
button
Intelia Class e Focus
INTELIA 01 INTRODUCTION
Saeco International Group Rev. 01 / September 2011 Page / 05
1.6.2 Internal machine parts
05
Boiler pin
Pump
Flow-meter
Power cable connector
Safety valve Boiler cover and
boiler
Power board
Grinding
adjustment insert
Steam pipe
KYB Interface card
2-way solenoid valve
Coffee grinder
Saeco International Group Rev. 01 / September 2011 INTELIA
CHAPTER 2
TECHNICAL
SPECIFICATIONS
INTELIA 02 TECHNICAL SPECIFICATIONS
Saeco International Group Rev. 01 / September 2011 Page / 03
2.1. Technical specifications
Power supply and output: 240 V~ 50 Hz 1850 W - 230 V~ 50/60 Hz 1850 W
Temperature monitoring: (NTC) variable resistor sensor - transmits the value to the
electronic card
Safety system: 2 thermostats at 190°C one shot
Coffee heat exchanger output:
Stainless steel
(230 V~) 1900 W
for coffee, hot water and steam dispensing
Steam heat exchanger output:
Stainless steel As above
Gear motor: 2 rotation directions; power supply 24VC
Pump: Ulka Type EP5/S GW approx. 13-15 bar with reciprocating
piston and thermal switch 100°C 48 W, 230V, 50 Hz, 120V,
60Hz 100V, 50/60 Hz
Overpressure valve: Opening at approx. 16-18 bar
Water filter: In tank
Coffee grinder: Direct current motor with flat ceramic grinder blades
Automatic dosage: Dose adjustment controlled by the electronic system
Power consumption: During heating phase- approx. 5.6 A
Dimensions: W x H x D in mm: 256x340x440
Weight: 9 kg
Water tank capacity: 1.5 l
Coffee bean hopper capacity: 300 g. of coffee beans
Dreg drawer capacity: 10
Heat exchanger capacity: 10 (11 if after 9 dregs you dispense a double espresso)
Water circuit filling time: Approx. 15 sec Max. on first filling cycle
Heating time: Approx. 45 sec.
Dispensing temperature: Approx. 73°-83°
Grinding time: Approx. 8-10 sec.
01
This manual suits for next models
2
Table of contents
Other Philips Coffee Maker manuals
Philips
Philips HD7892 User manual
Philips
Philips HD5720/30 User manual
Philips
Philips Cafe Comfort HD7448/20 User manual
Philips
Philips HD7817/60 User manual
Philips
Philips Senseo HD7863/80 User manual
Philips
Philips HD7751 User manual
Philips
Philips HD8930/02 User manual
Philips
Philips HD7446 User manual
Philips
Philips HD7740/00 User manual
Philips
Philips HD8323/08 User manual
Philips
Philips Saeco Syntia HD8836 User manual
Philips
Philips HD7900 User manual
Philips
Philips Xelsis HD8943 User manual
Philips
Philips HD7692/90 User manual
Philips
Philips HD7850/61 User manual
Philips
Philips HD7761 User manual
Philips
Philips HD7818/50 User manual
Philips
Philips HD7562/35 User manual
Philips
Philips Senseo HD7830 User manual
Philips
Philips Senseo HD7860/10 User manual
