Philips SCF250/00 User manual

SCF250

User manual 4

Mode d’emploi 10

Instrucciones de manejo 16

Bedienungsanleitung 22

Gebruiksaanwijzing 28

Istruzione per l’uso 34

Manual de utilização 40

Od  46

Bruksanvisning 52

Vejledning 58

Bruksanvisning 64

Käyttööhje 70

Functional Overview - Product illustration on inside flap

1Bottle and jar lifter

2Hand grips

3Mains plug

4Click-step control knob

5Indicator lamp

6Ring with water cup

7Container

8Cable reservoir

Important Safeguards

• Read and save these instructions

• Never use the unit without water in it.

• Do not touch hot surfaces. Use handles or grips.

• Do not move an appliance containing hot liquids.

• Do not immerse appliance, cord or plugs in water or other

liquid.

• Close supervision is necessary when the unit is used near

children.

• Do not let cord hang over edge of table or counter.

• Do not place on hot surfaces or in a heated oven.

• Test food on inside of hand before serving to ensure it is at a

safe temperature for your baby.

• Use only containers that have been approved for boiling.

• Only use the Baby Bottle Warmer when the ambient

temperature is between +7ºC and +37ºC.

ENGLISH4

Installation

Before connecting the Baby Bottle Warmer to the mains, check to

ensure that the mains outlet is 230V AC.

1Place the Baby Bottle Warmer out of the reach of children

and on a dry, non-slip, horizontal surface.

2Turn the click-step control knob 4to the left to the

‘0’ (OFF) position.

> The indicator lamp lights green.

3Unreel the required cable length from the cable reservoir 8

and plug into the mains outlet.

Operation

Warming of baby bottles

1Turn the click-step control knob 4to the left to the

‘0’ (OFF) position.

2Connect the bottle warmer to the mains socket.

> The indicator lamp lights green.

3Fill the beaker with 10 or 20ml water by using the water cup

of the ring 6.The content is depending on the bottle filling

and start temperature (see Heating Overview on page 3).

4Place the bottle in the middle of the beaker and put the ring

6on top of it.

5Use the click-step control knob 4to set the correct setting

(see Heating Overview on page 3).

> The indicator lamp lights red.

> When the right temperature is reached the indicator lamp

will light green.

6Remove the bottle from the container and turn the control

knob to the ‘0’ (OFF) position.

ENGLISH 5

7Shake the bottle a little bit to distribute the heat evenly

before you allow your baby to drink.

8Check that the contents of the bottle are the correct

temperature by pouring a few drops on the back of your

hand.

Notes!

– The ring ensures that the hot steam heats up the bottle extremely

fast to the right temperature.Warming the bottle without the ring,

might result in a wrong temperature, therefore never use the bottle

warmer without the ring.

– The dimensions of the bottle or the material of the bottle (glass in

stead of plastic) may influence selecting the correct knob setting.

Therefore always control the end temperature and adjust the setting

of the knob.

Warning! When you leave the bottle in the bottle warmer after it is

heated up, the temperature might increase a few degrees.

Warming baby food jars

1Turn the click-step control knob 4to the left to the

‘0’ (OFF) position.

2Connect the bottle warmer to the mains socket.

> The indicator lamp lights green.

3Remove the label and lid from the jar.

4Fill the beaker with 20ml water by using the water cup of the

ring.

5Place the jar in the middle of the container and put the ring

on top of it.

6Set the click-step control knob to the symbol.

> The indicator lamp lights red.

> When the right temperature is reached the indicator lamp

will light green.

ENGLISH6

7Remove the jar from the container and turn the control

knob to the left to the ‘0’ (OFF) position.

8Stir the contents of the jar to distribute the heat.

9Always check that the contents of the jar are at the correct

temperature by testing some on the back of your hand or via

your mouth.

10 If the temperature is much too low, fill the beaker again with

10ml.Turn the click-step control knob 4to the right until

the indicator lamp lights up red to start the heating up again.

Note! The ring ensures that the hot steam heats up the jar extremely

fast to the right temperature.Warming the jar without the ring,

might result in a wrong temperature, therefore never use the

bottle warmer without the ring.

Keeping warm

With the Baby Bottle Warmer you can also keep the bottles and

jars warm for a short time.

To do this set the control knob to the symbol. Do not add

water.The thermostat ensures that the set temperature is

maintained. For microbiological and hygienic reasons baby food

should never be kept warm for longer than one hour.

Note! Never hold the Baby Bottle Warmer in your hands when in use.

ENGLISH 7

Maintenance

Cleaning

• Disconnect the Baby Bottle Warmer from the mains socket

and allow it to cool down. Clean the container and the

outside of the Baby Bottle Warmer with a damp cloth.

Notes: – Never immerse the Baby Bottle Warmer in water.

– Do not use cleaning or scouring agents.

Warning: If a fault occurs, consult a Philips’ service centre. Under no

circumstances should you try to repair the Bottle Warmer

yourself; do not dismantle. Servicing should be performed by

qualified service personnel only.

Technical Specifications

Power supply (mains): 220-240V AC

Power consumption (mains): 250 Watts

Operational ambient temperature: between +7°C and +37°C

Protection: PTC temperature controlled

heating system

Problem solving

Problem Solution

Temperature too low. • Turn the click-step control knob

4to the right until the indicator

lamp lights up red to start the

heating up again.

• Check ring filling and start

temperature.

Temperature too high. • Lower the adjustment setting.

• Check ring filling and start

temperature.

ENGLISH8

The jar has not been Stir the contents from time to time

heated correctly. while heating. Check that the

click-step control knob is in the

position.

Unit does not warm up. Wait 15 minutes between

consecutive uses to allow the safety

cut-out to reset.

The indicator light This is normal; it may turn on or off

switches on and off while heating.

while keeping warm.

Indicator light does not Shield indicator from ambient light

seem to light. to improve visibility.

The bottom of the tank Hard water deposits are normal

is spotted. and may increase if your water is

very hard; remove the deposits

periodically with white vinegar

(see maintenance).

Guarantee & service

If you need information or if you have a problem, please visit the

Philips website at www.philips.com or contact the Philips Customer

Care Centre in your country (you will find its phone number in the

worldwide guarantee leaflet). If there is no Customer Care Centre

in your country, turn to your local Philips dealer or contact the

Service Department of Philips Domestic Appliances and Personal

Care BV.

ENGLISH 9

Fonctionnement -

Illustration du produit sur le rabat intérieur

1Biberon et élévateur de pot

2Poignées

3Fiche secteur

4Sélecteur à déclic

5Témoin

6Bague avec cuillère de mesure

7Conteneur

8Cable reservoir

Mesures de sécurité importantes

• Lire et conserver ces instructions.

• Ne jamais utiliser l’appareil sans qu’il soit rempli d’eau.

• Ne pas toucher les surfaces chaudes. Utiliser les leviers ou

les poignées.

• Ne pas déplacer un appareil contenant des liquides chauds.

• Ne pas immerger l’appareil, le cordon ou la fiche dans de

l’eau ou tout autre liquide.

• Surveillance rigoureuse nécessaire lorsque l’appareil est

utilisé à proximité d’enfants.

• Ne pas laisser le cordon d’alimentation pendre sur le bord

d’une table ou d’un plan de travail.

• Ne pas mettre sur des surfaces chaudes ou dans un four

chaud.

• Tester la température de l’aliment sur la paume de la main

avant de servir pour être sûr qu’il n’y a pas de danger pour

votre bébé.

• Utiliser uniquement des récipients approuvés pour ébullition.

• Utiliser uniquement le chauffe-biberon lorsque la

température ambiante est entre +7ºC et +37ºC.

FRANÇAIS10

This manual suits for next models

Table of contents

Languages:

Other Philips Bottle Warmer manuals

Philips

Philips SCF355 User manual

Philips

Philips SCF355 User manual

Philips

Philips SCF355 User manual

Philips

Philips HD4331/01 User manual

Philips

Philips AVENT SCF66 Series User manual

Philips

Philips SBCSC215/87 User manual

Philips

Philips SCF355 User manual

Philips

Philips Avent SCH820/00 User manual

Philips

Philips SCF255/52 User manual

Philips

Philips AVENT scf356 User manual

Philips

Philips SCF355/04 User manual

Philips

Philips AVENT scf356 User manual

Philips

Philips SCF255/51 User manual

Philips

Philips SCF355/05 User manual

Philips

Philips SCF355 User manual

Philips

Philips SCF355 User manual

Philips

Philips SCF355 User manual

Philips

Philips SCF355 User manual

Philips

Philips AVENT SCF358 User manual

Philips

Philips AVENT SCF355/07 User manual

Philips

Philips AVENT SCF356/00 User manual

Philips

Philips AVENT scf356 User manual

Philips

Philips SCF355 User manual

Philips

Philips SBCSC230/05 User manual

Popular Bottle Warmer manuals by other brands

Topcom

Topcom KD-4302 user guide

SEVERIN

SEVERIN BK-3177 Instructions for use

SEVERIN

SEVERIN BK 3176 Instructions for use

Chicco

Chicco 06867 MU owner's manual

Reer

Reer Multimax 2 in 1 -travel operating manual

Lionelo

Lionelo Thermup Go user manual

TEFAL

TEFAL Disney Baby TD1100K0 manual

TrueLife

TrueLife INVIO BW Single user manual

Gourmia

Gourmia JBW-250 user manual

König Electronic

König Electronic HC-BW10 manual

Gourmia

Gourmia JBW-150 user manual

NUK

NUK MEDICPRO 10.256.467 operating instructions

Petra

Petra DI 6.00 Instructions for use

Philips AVENT

Philips AVENT Electric Bottle and Baby Food Warmer user guide

babymoov

babymoov Auto Speed Bib Instructions for use

Alecto

Alecto BW600 instruction manual

Lionelo

Lionelo Thermup user manual

Vinotemp

Vinotemp VT-Chiller user guide