Perle IDS-108F User manual
P/N 5500339-10 (Rev E)
Perle IDS-108F(XT)
Unmanaged 10/100
Ethernet Switches
Installation Guide
- 2 - IDS-108F Installation Guide
Overview
This document contains instructions necessary for the installation
and operation of the Perle IDS-108F Ethernet switch. This
Ethernet switch can be ordered as an 8-port RJ-45 switch or as an
8-port RJ-45 switch with one or two SC or ST fiber ports. The fiber
ports can be either single mode (SM) or multimode (MM)
depending on the model selected and they can operate over
different wavelengths and distances. Visit the Perle website for the
most up to date installation guides, models and specifications.
http://www.perle.com/
Note: xxxxxxxx indicates models numbers for this product line.
TP = twisted pair
XT – Extended Temperature models
Features
•10/100Base-TX, one or two ST/SC fiber ports, multi/single
mode
•IEEE 802.3/802.3u/802.3x
•10/100, Full/Half duplex, MDI/MDIX with auto-sensing
•Auto-negotiation on copper ports
•Redundant DC power inputs
•Rugged high-strength case
•Industrial temperature models
•Din-rail or wall/panel mounting
Note – In this guide the various models will be referred to as the IDS-108F
Model
Port 1-8
Port 9 and 10
IDS-108F TP (RJ-45) empty
IDS-108F-xxxxxxxx TP (RJ-45) 1 or 2 fiber
ports
IDS-108F-XT
(Industrial Temperature Model) TP (RJ-45) empty
IDS-108F-xxxxxxxx-XT
(Industrial Temperature Model) TP (RJ-45) 1 or 2 fiber
ports
IDS-108F installation Guide
-
3
-
Getting to know your IDS-108F Switch
Package Contents:
•IDS-108F
•DIN-rail mounting clip (pre-installed on the unit)
•This guide
Note – Optional panel/wall mounting kits may be ordered for the IDS-108F
Front View of IDS-108F
(8 port RJ-45)
- 4 - IDS-108F Installation Guide
Front View of IDS-108F
(with two Fiber ports)
IDS-108F installation Guide
-
5
-
Bottom view of the IDS-108F
(with two ST fiber
ports)
Top view of the IDS-108F
Specifications
Terminal block Header (J1) – Cat. No. 5EHDR-04P,
manufacturered by Dinkle Enterprise Co., Ltd. Rated 300 V, 15 A,
105°C, FW-1.
Terminal block Plug – Cat. No. 5ESDV-04P, manufacturing by
Dinkle Enterprise Co., Rated 300 V, 105°C, FW-2, suitable for 28-
12 AWG (0.0804-3.31 mm2), torque value 4.5 lb-in.
Power
The IDS-108F switch has two power inputs that can be connected
simultaneously to DC or AC power sources. If one power source
fails, the other acts as a backup, and automatically powers the
switch.
- 6 - IDS-108F Installation Guide
Reset Button
To reset the IDS-108F insert a paper clip into the air hole vent and
gently press the reset button. The LEDs on the IDS-108F will go
On and then momentarily Off when released to show that the unit
has been reset. All links will be dropped and the MAC tables will
be cleared.
Status LED
(with two fiber ports)
P1 / P2– Power (Green LED)
On: Power present
Off: No Power present
Fiber Port 9/10 (Green LED)
On: Link up
Flashing: Link up and Ethernet activity detected
Off: Link down
Ethernet Port Status
Port Link / Speed (Green and Yellow LEDs)
On: Link Up
o100 Mbps Yellow on
o10 Mbps Yellow off
Flashing: Link up and Ethernet activity detected
Off : Link down
IDS-108F installation Guide
-
7
-
Dimensions for the IDS-108F
- 8 - IDS-108F Installation Guide
IDS-108F installation Guide
-
9
-
Mounting the IDS-108F on a DIN-rail
1. The DIN-rail clip will be fixed to the back panel of the IDS-
108F switch when you receive the product.
2. Position the IDS-108F such that the top of the DIN rail fits into
the slot on the top of the DIN-rail clip, just below the DIN-rail
hook and behind the spring.
3. While pushing down on the unit to compress the spring, rotate
the bottom of the IDS-108F toward the rail. This will snap the
bottom of the rail into the bottom of the clip. See diagram
below.
Note: To remove the IDS-108F from the DIN-rail, push down slightly on the
IDS-108F unit while pulling the bottom out.
Wall Mounting the IDS-108F
1. Remove the DIN-rail clip from the rear panel on the IDS-108F.
2. Attach the wall mount plates to the IDS-108F as shown below
using the screws provided in the kit.
- 10 - IDS-108F Installation Guide
3. Use the wall mount plates as a guide to mark the spots where
the screws will be.
4. Drive the screws into the wall leaving about 2 mm of the screw
protruding from the wall to allow room for sliding the wall
mount panel between the wall and the screws.
5. Once the screws are fixed to the wall, insert the four screw
heads through the large parts of the keyhole shaped screw
openings.
6. Pull the IDS down to lock the IDS-108F to the wall mount.
7. Tighten the four screws securely to the wall.
Note: For the best results use screws that have the following attributes:
Head diameter .5 - .6 mm
Shaft diameter 3 - 3.5 mm
Note: the dimensions are in mm
This manual suits for next models
1
Table of contents
Other Perle Switch manuals
Perle
Perle IDS-409-SFP Manual
Perle
Perle IDS-205 User manual
Perle
Perle IOLAN STS8D GR Manual
Perle
Perle IDS-409C User manual
Perle
Perle IDS-509-2SFP Manual
Perle
Perle IDS-509-SFP User manual
Perle
Perle IDS-409 User manual
Perle
Perle IDS-305G User manual
Perle
Perle IDS-509GPP User manual
Perle
Perle IOLAN SDG1 W Manual
Perle
Perle IDS-409F User manual
Perle
Perle IDS-205G User manual
Perle
Perle IDS-509PP8 User manual
Perle
Perle IDS-409G User manual
Perle
Perle IDS-206 Manual
Perle
Perle IDS-205G Manual
Perle
Perle IDS-509-SFP Manual
Perle
Perle RPS1620 User manual
Perle
Perle RPS830 User manual
Perle
Perle IDS-105FE Series User manual
