PEERLESS ULTRAVIEW Series User manual
12017-02-17 #:180-9099-4 (2019-03-28)
ULTRAVIEW™UHD OUTDOOR TELEVISION
MODEL: UV492, UV552, UV652
User Guide
ENG
22017-02-17 #:180-9099-4 (2019-03-28)
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, species
that the cable ground shall be connected to the grounding system of the facility. Outlet shall be
installed near the equipment and shall be easily accessible.
Antenna discharge unit
(NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding
electrode system
(NEC Art 250 Part H)
Grounding conductors
(NEC Section 810-21)
Antenna lead-in wire
Power Source
The display must be connected to a mains socket outlet with a protective grounding connection.
The mains plug is used as the disconnect device and shall remain readily accessible.
Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.
An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.
If an outside antenna is connected to the receiver, conrm that the antenna system is grounded to
protect against voltage surges and built up static charges. Section 810 of the National Electric Code,
ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to grounding electrodes and requirements
for the grounding electrode.
This display operates on 100-240 volts 50-60 Hz, AC current. Insert the power cord into a 120 volt
60 Hz outlet. Never connect the display to direct current or anything other than the specied voltage.
To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
All secondary lines must be routed through grounded conduit and kept separate from AC line.
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150
to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
32017-02-17 #:180-9099-4 (2019-03-28)
Relevant Information
Record your display's model and serial number here for future reference. Keep this user manual in an
accessible location in the event service is required.
Note: Your display's serial number can be found on the box and underneath the rear cover plate.
Model Number ____________________________________
Serial Number ____________________________________
FCC CAUTION
To assure continued compliance and possible undesirable interference, ferrite cores may be used
when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to
other peripheral devices.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with these instructions,
may cause harmful interference to radio communications; however, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/display technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation.
42017-02-17 #:180-9099-4 (2019-03-28)
Read before operating equipment
Thank you for purchasing our product. Before using it, please read this user guide carefully and follow
the instructions for safe operation. Please keep this manual for future reference and always include it
when transferring or transporting this product to a dierent location.
GENERAL SAFETY PRECAUTIONS
In case of emergency such as re or electric shock caused by the product, immediately contact 911
or proper emergency police/re service agencies in your country.
To reduce the risk of electric shock or re, heed the following:
• In case of product malfunction or unusual events such as electrical burning smell, smoke, or
loss of content signals due to internal overheating, immediately turn o, unplug the electrical
cord and contact the manufacturer.
• Do NOT disassemble, modify or service product in any way other than that contained in this
instruction. Any unauthorized modications made to the product automatically void product
warranty.
• Do NOT touch antenna lines or wires, electrical cables or plugs when lightning or thunder is
present or with wet hands
• Do NOT submerge in water.
• Do NOT destroy, process, or place close to any heat source.
• Do NOT install near poisonous gas or chemically unstable atmosphere.
• Do NOT install near strong magnetic or electrical current eld.
• Do NOT install the product in unstable locations or near moving objects, constantly vibrating
equipment, or uneven surfaces.
• Do NOT leave any re source, such as candles, close to or on the product.
• Do NOT operate the product if it has been dropped or struck. Severe physical impact to the
product may cause components to fall out of place within and break.
• Do NOT bend or twist electrical cords, electrical plugs, cables, or wires with excessive force.
• Do NOT block ventilation slots or place any heavy object on the product.
• Use properly rated electrical voltage.
• Do NOT use any electrical sockets or power strips with many other devices jointly plugged
in. Use a single, directly dedicated and rated GFCI electrical outlet for the product for safe
operation.
• Do NOT move or transport with any cables (electrical, content connectivity) plugged in to the
source devices.
• Always connect the electrical plug rmly and completely. When disconnecting any cables,
always pull on the plug and not the cord.
• Always leave the power o when plugging or unplugging the electrical cords or connection
cables.
• Do not defeat the safety purpose of the polarized or grounding type electrical plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not t into your outlet, consult an electrician for replacement of the obsolete
outlet.
• Protect the electrical cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
WARNING
52017-02-17 #:180-9099-4 (2019-03-28)
WARNING
• Never apply pressure to the exterior of the LCD screen.
• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.
• Do NOT climb on the product.
• Do NOT install within ve feet from a body of water.
• Do NOT use if ambient air temperature exceeds the operating limits.
• Do NOT install in enclosure or recessed cavity with less than 2 inches of airow around the
display. Air inside fully encased display must be ventilated.
• The product is to be secured to building before operation.
• Product must be carried and supported by at least two persons.
• Periodically clean dust o the electrical plug to keep it clean and dry, ensuring proper and safe
operation.
• Only use attachments/accessories specied by the manufacturer.
62017-02-17 #:180-9099-4 (2019-03-28)
System Installation And Electrical Requirements ..................................................................................2
Electrical Code ...............................................................................................................................2
Power Source ................................................................................................................................2
FCC Caution...................................................................................................................................3
FCC Statement...............................................................................................................................3
Relevant Information .....................................................................................................................3
General Safety Precautions ...................................................................................................................4
Set Up Instructions .................................................................................................................................7
Parts List ........................................................................................................................................7
Removing Cord Cover....................................................................................................................8
Connecting Cords ..........................................................................................................................9
Installing IR Extender .....................................................................................................................9
Replacing Cord Cover .................................................................................................................10
Connecting To The Power Source................................................................................................11
Prepare The Display For Mounting ..............................................................................................12
Remote Control Battery Installation And Replacement ................................................................14
Operating Instructions ..........................................................................................................................15
Power On/O the Display.............................................................................................................15
Onboard Controls.........................................................................................................................15
Navigating The On-Screen Menu ................................................................................................16
Channel ...............................................................................................................................16
Picture .................................................................................................................................16
Audio ...................................................................................................................................16
Time ....................................................................................................................................17
Setup ...................................................................................................................................17
Lock .....................................................................................................................................18
USB Functionality ........................................................................................................................19
(RS-232C) Serial Control Of The TV ...........................................................................................21
Maintenance ........................................................................................................................................22
Care Of Screen ...........................................................................................................................22
Mobile Telephone Caution ...........................................................................................................22
End Of Life Directives ..................................................................................................................22
Product Specications .........................................................................................................................23
Display..........................................................................................................................................23
Power ..........................................................................................................................................23
TV Controller Features ................................................................................................................23
Environmental .............................................................................................................................23
Mechanical ..................................................................................................................................24
Input/Output Connections ............................................................................................................24
Warranty ..............................................................................................................................................25
CONTENTS
72017-02-17 #:180-9099-4 (2019-03-28)
SET UP INSTRUCTIONS
Parts List
Description Qty
Atelevision 1
Bdisplay dust cover 1
Cremote 1
Dthumb screw (preinstalled) 4
EIR extender 1
Fuser guide (not shown) 1
C (1)
A (1)
B (1)
D (4)
remote
television
display dust
cover
thumb screw
AUX
LAST
OK
INFO
+
EXIT
CBLDVD
MUTE
POWER
VCR SAT
SOURCE
TV
1
4
7
.
2
5
8
0
3
6
9
VOL
REW PLAY FF MENU
REC STOP PAUSE GUIDE
CH
AUX
LAST
OK
INFO
+
EXIT
CBLDVD
MUTE
POWER
VCR SAT
SOURCE
TV
1
4
7
.
2
5
8
0
3
6
9
VOL
REW PLAY FF MENU
REC STOP PAUSE GUIDE
CH
AUX
LAST
OK
INFO
+
EXIT
CBLDVD
MUTE
POWER
VCR SAT
SOURCE
TV
1
4
7
.
2
5
8
0
3
6
9
VOL
REW PLAY FF MENU
REC STOP PAUSE GUIDE
CH
E (1)
IR extender
IR
IN
82017-02-17 #:180-9099-4 (2019-03-28)
Removing Cord Cover
Remove (4) thumb screws (D) and cord cover plate to access source connection panel. Do not
disconnect lanyard.
A
D (4)
lanyard
92017-02-17 #:180-9099-4 (2019-03-28)
Connecting Cords
RS-232C
Audio Out
USB 2.0 Data
DisplayPort
HDMI 1 (ARC)
HDMI 2
HDMI 3 (MHL)
VGA
Audio In
S/PDIF Optical
IR Extender
Mini Component
Mini AV
Antenna or Cable
12VDC 2.5A USB 5VDC 2.4A
4
USB 2.0
Data
Installing IR Extender (Optional)
IR
IN
E
Insert the 3.5mm end of the included 5V
IR extender into the IR Extender port on
the input panel of the display. IR extender
port may not be compatible with other 3rd
party extenders.
Connect source devices to appropriate display input. Make all connections prior to powering on the
display. The USB 2.0 Data port is for service and media only. For 5VDC power, use the 5VDC power
port.
10 2017-02-17 #:180-9099-4 (2019-03-28)
Replacing Cord Cover
1. Run cables across foam gasket block. Leave approximately 1/2" (13mm) between cables to
ensure a proper seal.
2. Replace cord cover plate and (4) thumb screws (D). Fasten thumb screws until gasket on cord
cover plate is fully compressed to back of television. Cables will seal between TV's gasket and
cord cover's gasket as cover is pressed into place. Route cables through opening at end of cord
cover.
D (4)
CAUTION
Do not overtighten screws
Failure to follow these instructions can result in the product being damaged,
destroyed, and voiding the warranty.
• Ensure cord bend radius does not exceed limits set by the
manufacturer.
• Ensure cords are seated properly in the cable channels to avoid
potential damage to cords when rear cover plate is installed.
• Do not remove lanyard that connects the rear cover plate to the display.
CAUTION
This manual suits for next models
3
Table of contents
Languages:
