PEERLESS PLP-UNL Guide
1 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-3 12-06-06
PLP-UNL PLP-UNL-S PLP-UNLP PLP-UNLP-
S
Description Qty Part # Part # Part # Part #
AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110
BB shallow adapter bracket 2 200-0756 200-0757 200-0754 200-0755
CC deep adapter bracket 2 200-0752 200-0753 200-0750 200-0751
DD allen wrench 1 560-9646 560-9646 560-0072 560-0072
EE M5 x 10mm screw 4 520-1063 520-1063 520-9250 520-9250
Before you begin, make sure all parts shown are included with your product.
Parts List
DD
CC
BB
Installation and Assembly - Universal Adapter
Bracket for 32" - 60" Flat Panel Screens Models: PLP UNL, PLP UNL-S,
PLP UNLP, PLP UNLP-S
IMPORTANT! Read instruction sheet before you start installation and assembly.
AA
Used with specific
mounts only EE
2 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-3 12-06-06
M5 x 25 mm (4)
520-1122
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
M5 x 12 mm (4)
520-1064 M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211
I.D. 5.6 mm (4)
540-1057
multi-washer(6)
580-1036
I.D. 8.7 mm (4)
540-1059
SecurityAdapter Bracket Fasteners
M6 x 20 mm (4)
520-9554
M6 x 30 mm (4)
520-1067
M8 x 15 mm (6)
520-1068
M8 x 40 mm (4)
520-1152
M8 x 25 mm (4)
520-1101
M6 x 20 mm (4)
520-9402
M6 x 30 mm (4)
510-9109 multi-washer(6)
580-1036
M8 x 16 mm (6)
520-9257
M8 x 40 mm (4)
520-1136
M4 x 12 mm (6)
504-9013
Phillips Adapter Bracket Fasteners
M4 x 25 mm (4)
504-1015
M5 x 12 mm (4)
520-1027 M5 x 25 mm (4)
520-9543
M6 x 12 mm (4)
520-1128
M6 x 25 mm (4)
520-1208
I.D. 5.6 mm (4)
540-1057
M8 x 25 mm (4)
520-1031
I.D. 8.7 mm (4)
540-1059
3 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-3 12-06-06
Note: "X" dimensions should be equal.
• Tighten screws so adapter brackets are firmly
attached. Do not tighten with excessive force.
Overtightening can cause stress damage to
screws, greatly reducing their holding power
and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.)
maximum torque.
WARNING
Installing Adapter Brackets
Refer to Screen Compatibility Chart to determine the proper fasteners to use.
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown in
figure 1.1.Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-
washers, and spacers as shown in figure 1.3.
Note: Top and bottom holes must always be used.
Verify that allholes areproperlyaligned, andthen tighten screwsusing a phillipsscrewdriver.
Note:Tightenusingsecurityallenwrench(DD).
• If screws don't get three complete turns in the screen
inserts or if screws bottom out and bracket is still not
tightly secured, damage may occur to screen or
product may fail.
WARNING
MEDIUM HOLE FOR M5
SCREWS
SMALL HOLE FOR M4
SCREWS
LARGE HOLE FOR M6 SCREWS
fig. 1.2
BB
or
CC
CENTER BRACKETS
VERTICALLY ON BACK OF
SCREEN
X
X
fig 1.1
Notes:
• Thenumberof fasteners usedwillvary,
depending upon the type of screen.
• Multi-washers and spacers may not be
used, depending upon the type of screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shownin figure1.2.
SCREWS
SPACERS
BB or CC
fig 1.3
MULTI-
WASHER
MULTI-WASHER
1
4 of 4 ISSUED: 11-11-05 SHEET #: 202-9060-3 12-06-06
Mounting and Removing Flat Panel Screen
Referto mountinstruction sheetfor attachmentof adapterbracket tomount.
Hook adapter brackets (BB or CC) onto adapter bracket (AA), then slowly swing screen in as shown. Turnscrews
clockwise at least six times to prevent screen from being removed as shown in detail 1.
Note:Tightenusingsecurityallenwrench(DD).
Screen can be adjusted horizontally if desired.
Note: To lock the screen down, tighten screws to adapter bracket as shown in detail 1.
Toremovescreenfrommount,loosenscrews,swingscreenawayfrom mount, and liftscreenoffofmount.
2
AA
BB or CC
DETAIL 1
SCREWS
AA
BB
or
CC
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark and Smart mount is a trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
This manual suits for next models
3
Other PEERLESS TV Mount manuals
PEERLESS
PEERLESS Smartmount D-FPT-220 Guide
PEERLESS
PEERLESS Jumbo 2000 JM 2630 Guide
PEERLESS
PEERLESS HP450-GB Guide
PEERLESS
PEERLESS PARAMOUNT PT660 Guide
PEERLESS
PEERLESS ECMU-01-C-S Guide
PEERLESS
PEERLESS PARAMOUNT PRFLU User manual
PEERLESS
PEERLESS PARAMOUNT PRTLU User manual
PEERLESS
PEERLESS PARAMOUNT PT640 and assembly Instruction Manual
PEERLESS
PEERLESS Peerless OneMount Flat Panel Modular Wall Mount... Guide
PEERLESS
PEERLESS SUF650P and assembly Guide
PEERLESS
PEERLESS SUF660P and assembly Guide
PEERLESS
PEERLESS SlimLine SLWS210/BK User manual
PEERLESS
PEERLESS PM1327 Guide
PEERLESS
PEERLESS LWS410/BK Guide
PEERLESS
PEERLESS Smartmount ST650 and assembly Guide
PEERLESS
PEERLESS LWS310/BK Guide
PEERLESS
PEERLESS SS550P and assembly Guide
PEERLESS
PEERLESS HP450 User manual
PEERLESS
PEERLESS Smartmount SA752PU User manual
PEERLESS
PEERLESS SR1G Instruction Manual
