PEERLESS HLG452-002 Guide
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Installation and Assembly
Flat-Panel Base Lock-Down Kit For Philips Display
Models
Models: HLG452-002, HLG452-002-Q10
Maximum Display Weight: 100 lb (45.35 kg)
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
2 of 6
NOTE: Read instruction sheet before you start installation and assembly.
Parts may appear slightly different than illustrated. A
D
Accessory
•ACC939 - 1/4-20 x 2.25" carriage screws for thicker
desktopsurfaces
•MIS660 - Neck Security Screws for 26HFL5830D/27,
32HFL5460D/27,32HFL5860D/27,32HF7965D/27,
37HFL5560D/27,42HFL5860D/27,42HFL7580A/27,
52HFL5580D/27
•ACC943:InstallationTemplate(plate only)
E
BC
Installation Option 1 (Fasteners) Pages 3 and 4
Installation Option 2 (Adhesive Strips) Pages 5 and 6
Qty. Part # Qty. Part #
Alock-down plate 1 090-1757 10 090-1757
B1/4-20 x 1 3/4" carriage bolt 2 520-1017 20 520-1017
Cplastic cap 2 590-1294 20 590-1294
D1/4-20 slope nut 3 530-0035 30 530-0035
Eadhesive strip 4 570-0017 40 570-0017
Parts List
Description
Before you begin, make sure all parts shown are included
with your product.
HLG452-002-Q10HLG452-002
Tools Needed for Assembly
• drill
• 1/4" drill bit
• 5/8" open box wrench
• phillips screwdriver
• 5/32 allen wench
•3M™Rubber& Vinyl80 SprayAdhesive(generic
name:Contact80 Neoprene VinylSprayAdhesive)
Thisproduct can be found at hardware and craft stores,
as well as on the 3M website: http://solutions.3m.com/.
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
3 of 6
Installation Option 1 (Fasteners)
1Use lock-down plate (A) as a template to mark location
of holes, point 1 and point 2, approximately 7" apart on
table. Drill two holes using a 1/4'' drill bit. 2
B
POINT 1 POINT 2
A
Slide two 1/4-20 x 1 3/4" bolts (B) through slots as
shownbelow.
NOTE:2 1/4"carriagebolts (ACC939)areavailable
forusewiththickermountingsurfaces.
TABLETOP
7"
(178 mm)
B.
DISPLAY MODEL HOLE PATTERNS
A.
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
42HF7945D/27
37HFL5560D/27
42HFL55860D/27
42HFL7945D/27
42HFL7580A/27
52HFL5580D/27
SBP240M/27
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
26HFL5830D/27
32HFL5460D/27
32HFL5860D/27
32HFL7560D/27
32HF7965D/27
32HFL7965D/27
C.
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
4 of 6
BOTTOMOFDESKTOP
4
DB
FIG 4.1
C
B
TIGHTENING
SLOPENUT
Hand tighten slope nut (D) through 1/4-20 x 1 3/4"
screw bolt (B) until snug against bottom of desktop
surface.Thread anotherslopenut (D)upside-down,
about two turns from first slope nut (D). Insert a open
boxwrenchbetweenboth slope nuts (D) and tighten.
NOTE:Avoidjamming bothslopenuts (D)together,
doing so may make it difficult to remove slope nut
used for tightening first slope nut (D).After slope nut is
secureremove bottom slope nut and add plastic cap
(C)as shown in figure 4.2. Repeat withremaining
1/4-20 x 1 3/4" screw bolt (B).
FIG 4.2
RUBBERFEET
Attach lock-down plate to display base bottom using
screwsprovidedby manufacturer.Refer to pagethree
for lock-down plate/ display base stand hole pattern.
NOTE: Removeexistingrubber feet from display base
thatinterfere with the lock-down plate.
NOTE:Displaybasestand and mounting
holelocations may appear differentthan
illustrated.
DISPLAYBASESTAND
A
3
SCREWS SUPPLIED BY
MANUFACTURER
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
5 of 6
Installation Option 2 (Adhesive Strips)
B.
DISPLAY MODEL HOLE PATTERNS
A.
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
42HF7945D/27
37HFL5560D/27
42HFL55860D/27
42HFL7945D/27
42HFL7580A/27
52HFL5580D/27
SBP240M/27
SCREWS SUPPLIED BY DISPLAY
MANUFACTURER
26HFL5830D/27
32HFL5460D/27
32HFL5860D/27
32HFL7560D/27
32HF7965D/27
32HFL7965D/27
C.
RUBBERFEET
Attach lock-down plate to display base bottom using
screwsprovided by manufacturer.Refer to lock-down
plate/ display base stand hole pattern.
NOTE: Removeexistingrubber feet from display base
thatinterfere with the lock-down plate.
NOTE:Displaybasestand and mounting
holelocations may appear differentthan
illustrated.
DISPLAYBASESTAND
A
SCREWS SUPPLIED BY
MANUFACTURER
42HF7945D/27 HOLE PATTERN SHOWN
ISSUED: 09-04-08 SHEET #: 090-9150-3 10-05-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
6 of 6
DRIED3M
RUBBERAND
VINYL#80 SPRAY
ADHESIVE
CLEANWITH
RUBBING
ALCOHOL
Cleanbottom of lock-down plate(A)with rubbing alcohol.Spraybottom of lock-downplate(A)only where tapewill
beapplied,with3Mrubberandvinyl#80sprayadhesive.Pullapartthefouradhesivestrips(E)andremovered
backing film on both sides. Wait at least 4 minutes to dry before applying adhesive strip (E). Attach adhesive
strips (E) firmly to bottom of lock-down plate (A) as shown below.
4
EA
Cleandesk surface with rubbing alcohol. Use 3M rubber and vinyl #80sprayadhesive(notsupplied)on the mounting
surface area only. NOTE: Spray adhesive will not remove easily. Wait at least 4 minutes to dry before removing tape
backingfromlock-downplate(A)andplacing firmly on surface. NOTE: There is a recommended 72 hour cure time for
tapeonlock-down plate (A).
NOTE: Once tape backing is removed be careful not to touch the sticky surface of the tape with fingers, as this can
cause the tape to lose some of its holding power.
NOTE: Afterapplicationoftapeonlock-down plate (A),the bond strength will increase as the adhesive flows onto the
surface.
Atroomtempurature, approximately 50%
oftheultimate strength will be achieved
after 20 minutes, 90% after 24 hours,
and 100% after 72 hours. In some cases,
bondstrengthcanbe achieved more quickly
by exposure to elevated temperatures
(e.g.150°F[66°C]for 1 hour).
DISPLAYBASESTAND
DRIED 3M RUBBERAND
VINYL #80 SPRAY
ADHESIVE(not supplied)
DESKSURFACE
NOTE: Displaybasestand may appear
differentthan illustrated.
This manual suits for next models
1
Table of contents
Other PEERLESS TV Mount manuals
PEERLESS
PEERLESS Smartmount ST630P and assembly Guide
PEERLESS
PEERLESS LWS210/BK Guide
PEERLESS
PEERLESS ACC 908 Guide
PEERLESS
PEERLESS SS550P and assembly Guide
PEERLESS
PEERLESS DS334 Guide
PEERLESS
PEERLESS Smartmount ST630P and assembly Guide
PEERLESS
PEERLESS SMARTMOUNT SA763PU User manual
PEERLESS
PEERLESS MM746PU User manual
PEERLESS
PEERLESS PARAMOUNT PF640 and assembly User manual
PEERLESS
PEERLESS SR1M Guide
PEERLESS
PEERLESS SR1M Guide
PEERLESS
PEERLESS PARAMOUNT PT630 and assembly Guide
PEERLESS
PEERLESS SP 850 and assembly Guide
PEERLESS
PEERLESS PARAMOUNT PT660 User manual
PEERLESS
PEERLESS PARAMOUNT PT632 and assembly Guide
PEERLESS
PEERLESS PARAMOUNT PRTLU User manual
PEERLESS
PEERLESS PLP PION50 Guide
PEERLESS
PEERLESS Smartmount SA752PU User manual
PEERLESS
PEERLESS PARAMOUNT PT640 and assembly Instruction Manual
PEERLESS
PEERLESS Jumbo 2000 OP-JMW2630 Guide
