PEERLESS Mounts Vector Pro II PJF2-UNV Series Guide

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

1 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

Read instruction sheet before you start installation and assembly.

Maximum UL Load Capacity: 50 lb (27 kg)

IMPORTANT! Be sure not to touch the projector while tightening the set screw on the

ball and socket mount. This may cause the image to be unaligned when you let go.

Applications:

Flush Mount .................................................................................................................................................. page 5

Extension Column ........................................................................................................................................ page 6

Installations:

To Wood Joist Finished Ceilings,

Exposed Wood Joists, or Wood Beam Ceilings ........................................................................................ page 3

To Concrete Ceilings .................................................................................................................................... page 4

IMPORTANT! Turn to the appropriate page for your ceiling installation.

Installation and Assembly - Vector Pro II™Models: PJF2-UNV, PJF2-UNV-S,

PJF2 SERIES

Refer to Model No. Guide Sheet

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

This product is intended for use with UL

Listed products and must be installed

by a qualified professional installer.

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

2 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

Parts List

Before you start check the parts list to insure all of the parts shown are included.

Black Silver

Description Qty. Part Number Part Number

Aball and socket mount 1 055-0011 055-0016

B4 mm security allen wrench 1 560-9646 560-9646

CM5 x .8 x 10 mm socket pin type F screw 1 520-1164 520-2031

D#10-32 x 3/8" spade thumb screw 1 560-1107 560-2107

E#10-32 x 3/8" serrated washer head socket pin screw 1 520-1151 520-2151

F#14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 5S1-015-C04

Gceiling plate 1 580-1042 580-4042

H.25" ID x .56" OD x .26 spacer 2 590-1050 590-2071

Iextension column connector with cord management 1 580-1025 580-4025

J#10-32 x 3/8" socket pin screw 2 520-1084 520-2084

K#10-32 x 3/16" slotted set screw 3 520-1187 520-2187

Note: Actual parts may appear slightly different than illustrated.

FASTENERS

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

3 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

WOOD

JOIST

CEILING

Drill two 5/32" (4 mm) dia. holes to a minimum

depth of 2.5" (64 mm). Attach ceiling plate (G)

with two #14 x 2.5" (6 mm x 65 mm) wood

screws (F) as shown using 3/8" (10 mm) socket

wrench.

Skip to step 2.

IMPORTANT: Be sure to drill holes into the

joistCENTER!

For optional Cord Management,

install two spacers (H) between ceiling

plate (G) and ceiling.

Installation To Wood Joist Finished Ceilings,

Exposed Wood Joists, or Wood Beam Ceilings

WOOD

JOIST

CEILING

• Tighten wood screws (F) so that wall plate (G) is firmly

attached, but do not overtighten. Overtightening can

damage the screws, greatly reducing their holding

power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Make sure that mounting screws are anchored into the

center of the studs. The use of an "edge to edge" stud

finder is highly recommended.

WARNING

• It is the responsibility of the installer to verify that the

supporting surface will safely support the combined

load of all attached hardware and components.

WARNING

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

4 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

Drill two 1/4" (6 mm) dia. holes to a minimum depth of

2.5" (64 mm). Attach ceiling plate (G) using two

concrete anchors and #14 x 2.5" wood screws (F) as

shown in Illustration A and 1, 2, and 3 (below).

Tighten all fasteners.

IMPORTANT: It is the responsibility of the installer

to verify that the ceiling will safely support the

combined load of all attached hardware and

components.

CUTAWAY VIEW

INCORRECT

concrete

metal

bracket

plaster/

dry wall

CORRECT

concrete

metal

bracket

plaster/

dry wall

concrete

ceiling

concrete

anchor

concrete

anchor

concrete

anchor

Illustration A

Installation to Concrete Ceilings

ACC 203 (Alligator® concrete anchors) are recommended.

•FOR DIRECT ATTACHMENT TO LOAD BEARING

CONCRETE ONLY! Concrete expansion anchors are

not intended for attachment to concrete ceilings

covered with a layer of plaster, drywall, or other

finishing material. If mounting to concrete ceiling

covered with plaster / drywall is unavoidable, plaster /

drywall must be counterbored as shown below.

WARNING

CONCRETE CEILING

concrete

anchor

Drill hole and insert anchor

Place ceiling plate over anchor and secure with screw

After repeating step one tighten all fasteners

• Tighten wood screws so that wall plate is firmly

attached, but do not overtighten. Overtightening can

damage the screws, greatly reducing their holding

power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Make sure that mounting screws are anchored into the

center of the studs. The use of an "edge to edge" stud

finder is highly recommended.

WARNING

• When installing Peerless wall mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface

in the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meet

ASTM C-90 specifications.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-

ware and components.

• Never exceed the Maximum UL Load Capacity of 50 lb (27 kg).

WARNING

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

5 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

Screw ball and socket mount (A) into ceiling plate (G). Align the notch with one of the four holes of the ceiling plate

(G) and secure ball and socket mount (A) with a M5 x 10 mm socket pin screw (C) using security allen wrench (B)

as shown in detail 1.

Note: Slotted set screw (K) is used to jam against the threads of the ball and socket mount to prevent any excess

movement of the ball and socket mount (A). Do not overtighten screw; overtightening screw will damage threads

making it difficult to separate the products.

Skip to step 3.

Flush Mount Application

DETAIL 1

WOOD

CEILING

NOTCH

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

6 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

Screw extension column to ceiling plate (G).

Align the notch with one of the four holes in

the ceiling plate (G) and secure extension

column with a M5 x 10 mm socket pin

screw (C) using security allen wrench (B).

See detail 4.

Screw extension column connector (I) to

extension column. Align slot in extension

column with one of the top holes in

extension column connector (I). Insert and

tighten one #10-32 x 3/8" socket pin screw

(J) through extension column connector (I)

into slot on extension column using security

allen wrench (B). See detail 5.

Screw ball and socket mount (A) to

extension column connector (I). Align slot in

ball and socket mount (A) to one of the

bottom holes in extension column connector

(I). Insert and tighten one #10-32 x 3/8"

socket pin screw (J) through extension

column connector into slot in ball and

socket mount (A) using security allen

wrench (B). See detail 6.

Note: Slotted set screws (K) are used to

jam against the threads of each connecting

joint to prevent any excess movement. Do

not overtighten screws; overtightening

screws will damage threads making it

difficult to separate the products.

DETAIL 6

SLOT

DETAIL 5

DETAIL 4

EXTENSION

COLUMN

Installation to

Extension Column

EXTENSION

COLUMN

SLOT

EXTENSION

COLUMN

SLOT

EXTENSION COLUMN

(UL Listed EXT or ADJ

Series)

Sold Separately

ISSUED: 05-25-05 SHEET #: 055-9247-6 11-08-06

Visit the Peerless Web Site at www.peerlessmounts.com

7 of 7

For customer care call 1-800-729-0307 or 708-865-8870.

To adjust roll, pitch, and yaw loosen the set screw

(shown below) using security allen wrench (B) or

standard 4 mm allen wrench. You should be able to

just slightly loosen the screw so that your adjustments

can be set without having to hold the projector. Move

projector to desired position and slowly tighten set

screw.

Note: Be sure not to touch the projector while

tightening the set screw. This may cause the image

to be unaligned when you let go.

IMPORTANT: Allen wrench is your key for projector

removal. Store it in a safe place.

Peerless offers several Projector Mounts to fit various

projectors. New Projector Mounts are continually being

developed to meet the demands of a growing projector

market. To find out if a mount is available for your particular

projector, call Peerless customer service at 1-800-729-

0307 or 1-708-865-8870.

Note: The projector adapter plate and projector you are installing may differ in appearance from the sample

illustrated below.

SET SCREW

Attach projector, with adapter plate already on it, to the

ball and socket mount (A) by inserting the ball and

socket mount (A) into the adapter plate connection and

twisting until the adapter plate will no longer turn

(about 75°). The spring loaded captive screw should

line up with a corresponding hole on the adapter plate

(this should line up automatically when the two are

connected). Push down and tighten the spring loaded

captive screw to secure the adapter plate to the mount.

If not using the optional security feature, fasten thumb

screw (D) in the hole opposite the spring loaded

captive screw.

OPTIONAL: For Armor Lock™security, insert serrated

washer head socket pin security screw (E) in the hole

opposite the spring loaded captive screw. Tighten with

security allen wrench (B). This will prevent the

projector from being removed.

Note: Be sure to only use the #10-32 x 3/8" screw (E)

(or the thumb screw (D)) opposite the spring loaded

captive screw.

WOOD

JOIST

CEILING

PROJECTOR ADAPTER PLATE

(UL Listed PAP Series)

Sold Separately

PROJECTOR

WOOD

JOIST

CEILING

PROJECTOR

CUTAWAY VIEW OF

CEILING PLATE (G)

CAPTIVE

SCREW

• Do not lift more weight than you can handle! Use

additional man power or mechanical lifting equipment

to safely handle placement of the projector!

WARNING

Peerless is a registered trademark of Peerless Industries, Inc. Vertor Pro II and Armor Lock are trademarks of Peerless Industries Inc.

All other brand and product names are trademarks or registered trademarks of their respective owners.

This manual suits for next models

Table of contents

Other PEERLESS Mounts Rack & Stand manuals

PEERLESS Mounts

PEERLESS Mounts SUT660P Guide

PEERLESS Mounts

PEERLESS Mounts LCT-A1B4C Guide

PEERLESS Mounts

PEERLESS Mounts FPEWM Guide

PEERLESS Mounts

PEERLESS Mounts SmartMount ST630P Guide

PEERLESS Mounts

PEERLESS Mounts ACC 310 Guide

PEERLESS Mounts

PEERLESS Mounts PRG UNV Guide

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3C Guide

PEERLESS Mounts

PEERLESS Mounts SmartMount SF630P Guide

PEERLESS Mounts

PEERLESS Mounts SmartMount ST635 Guide

PEERLESS Mounts

PEERLESS Mounts Smartmount D-FPF-220 Guide

PEERLESS Mounts

PEERLESS Mounts FPECMC-01 Guide

PEERLESS Mounts

PEERLESS Mounts SmartMount ST632P Guide

PEERLESS Mounts

PEERLESS Mounts Paramount PF660 Guide

PEERLESS Mounts

PEERLESS Mounts LCT-A1B1C Guide

PEERLESS Mounts

PEERLESS Mounts DS-VL-H060 Guide

PEERLESS Mounts

PEERLESS Mounts LCT-A1B3H Guide

PEERLESS Mounts

PEERLESS Mounts LCT-A1B2H Guide

PEERLESS Mounts

PEERLESS Mounts RTLA-100 Guide

PEERLESS Mounts

PEERLESS Mounts PLA 50-UNL Guide

PEERLESS Mounts

PEERLESS Mounts DS-VL-H048 Guide

PEERLESS Mounts

PEERLESS Mounts ACC328 Guide

PEERLESS Mounts

PEERLESS Mounts SmartMount SA740P Guide

PEERLESS Mounts

PEERLESS Mounts LCT-A1B6C Guide

PEERLESS Mounts

PEERLESS Mounts Solid-Point PLA 2 Guide

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 