Peerless-AV SA752PU Guide

Models: SA752PU

Installation and Assembly:

Universal Articulating Arm Wall Mount for 32" to 52" Flat Panel

Displays

ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

Max UL Load Capacity: 90 lb (40.8 kg)

2 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Note: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.............................................................................................................................................................................3, 4

Wall installation...................................................................................................................................................................5, 6

Installing Adapter Brackets to Display ...............................................................................................................................7-11

Mounting Flat Panel Display.................................................................................................................................................12

Cable Management ..............................................................................................................................................................14

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• phillips screwdriver

• 5/32" (4mm) drill bit for wood studs

• 5/16" (8mm) drill bit for concrete and cinder block

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

•Metal Stud Contact Qualiﬁed Professional (not evaluated by UL)

•Brick Contact Qualiﬁed Professional (not evaluated by UL)

•Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

CDE FG

Description Qty. Part #

Awall arm assembly 1 095-P1990

Buniversal adapter bracket 1 095-P1635-2

Cwood screws 4 520-1202

Dconcrete anchors 4 590-0320

EM10 x 15 mm socket head screw 2520-9262

Ffastener caps 4590-1324

Gcable ties 8590-1168

H6 mm allen wrench 1 560-9716

I5 mm allen wrench 1 560-9640

Jrear cable cover 2 590-P1326

Kfront cable cover 2 590-P1327

L#3 screwdriver bit (not shown) 1 560-0209

M5/32 allen wrench 1 560-9646

Parts List

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

4 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Adapter Bracket Fasteners

M4 x 12mm (6)

(504-9013)

M4 x 25mm (4)

(504-1015)

M5 x 12mm (4)

(520-1027) M5 x 25mm (4)

(520-9543)

M8 x 16mm (6)

(520-9257)

M8 x 40mm (4)

(520-1136)

M8 x 25mm (4)

(520-1031)

I.D. .34" (4)

(540-1059)

I.D. .22" (4)

(540-1057)

M6 x 30mm (4)

(510-9109)

M6 x 12mm (4)

(520-1128) M6 x 25mm (4)

(520-1208)

M6 x 20mm (4)

(520-9402)

multi-washer (6)

(580-1036)

5 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Using a stud ﬁnder, locate and mark the edges of the wood stud. Use a level to draw a vertical line down the center

of the stud and mark the desired display center. Use wall plate template (wall arm) to mark center of holes along

the vertical line. The top mounting hole should be 7.54" (192mm) above the desired display center as shown in

ﬁgure 1.1. Drill four 5/32" (4mm) dia. holes to a depth of 2.5" (64mm). Attach wall arm (A) to wall with four wood

screws (C) using #3 phillips screwdriver bit (L) as shown in ﬁg. 1.2. Level then tighten all fasteners.

Insert four fastener caps (F) into wall plate mounting holes.

Installation to Single Wood Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

7.54"

(192mm)

DC = DISPLAY CENTER

WOOD STUD

WALL PLATE

ﬁg. 1.1

ﬁg. 1.2

WARNING

6 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Installation to Solid Concrete or Cinder Block

Mark the desired display center and use wall plate

template (wall plate) to mark mounting holes. The

top mounting hole should be 7.54" (192mm) above

the desired display center as shown in ﬁgure 1.1

on page 5. Drill four 5/16" (8mm) dia. holes 2.5"

(64mm) deep as shown in ﬁg. 1.3. Insert anchors

(D) into holes ﬂush with wall. Place wall arm (A)

over anchors and secure with four wood screws (C)

using #3 screwdriver bit (L). Level then tighten all

fasteners.

Insert four fastener caps (F) into wall plate mounting

holes.

ﬁg. 1.3

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual

concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount

in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM

C-90 speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to

concrete covered with plaster, drywall, or other

ﬁnishing material. If mounting to concrete surfaces

covered with a ﬁnishing surface is unavoidable (not

evaluated by UL), the ﬁnishing surface must be

counterbored as shown below. Be sure concrete

anchors do not pull away from concrete when

tightening screws. If plaster/drywall is thicker than

5/8" (16mm), custom fasteners must be supplied by

installer (not evaluated by UL).

WARNING

SOLID CONCRETE

CINDER BLOCK

WALL PLATE

WARNING

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

plaster/

drywall plaster/

drywall

concrete concrete

7 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

NOTE: If display has a VESA 400 horizontal

mounting pattern, skip to step 2-3 or 2-4 on page 9.

NOTE: For VESA 200x200 or VESA 200x100 mount

hole patterns, skip to step 3 on page 10.

NOTE: For dedicated PLP plate installation skip to

step 4 on page 12.

Remove four 1/4-20 x .6" screws using 5mm allen

wrench (I) and loosen two 1/4-20 x 1.25" screws 1/2

turn to allow for display bracket adjustment.

1/4-20 x .6" SCREWS

1/4-20 x 1.25" SCREWS

To prevent scratching the display, set a cloth on a ﬂat, level surface that will support the weight of the display.

Place display face side down and refer to display manufacturers instructions for removing obstructions from the

back of the display. Adjust display brackets to align with display mounting holes.

Measure horizontal mounting hole pattern and choose ﬁxed stop-position from chart below.

2-1

FIXED STOP-POSTION #2

FIXED STOP-POSTION #1

FIXED STOP-POSTION #3

horizontal mounting hole pattern fixed stop-position

10-3/4" - 16-1/16" (273 - 408 mm) #1

15-1/16" - 21-9/16" (383 - 548 mm) #2

20-7/16" - 27-9/16" (519 - 700 mm) #3

Installing Adapter Brackets to Display

8 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Select the screws from the bafﬂed fastener pack that best ﬁt your display and secure to display following step 2-3

or 2-4 on page 9.

NOTE: Top and bottom mounting holes must be used for attaching display brackets. Middle holes should also be

used where the fasteners and displays allow.

Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.

CENTER DISPLAY BRACKETS VERTICALLY AND

HORIZONTALLY ON BACK OF DISPLAY

DISPLAY

DISPLAY BRACKETS

NOTE: "X" dimensions should be equal.

"Y" dimensions should be equal.

• Tighten screws so display brackets are ﬁrmly attached to display. Do not tighten with excessive force.

Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing

screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to display or product may fail.

WARNING

2-2

Installing Adapter Brackets to Display

9 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Begin with the shortest length screw, hand thread

screw through multi-washer and display brackets

(B) into display as shown below. Screw must make

at least three full turns into the mounting hole and

ﬁt snug into place. Do not over tighten. If screw

cannot make three full turns into the display, select

a longer length screw from the bafﬂed fastener

pack. Repeat for remaining mounting holes, level

display brackets and tighten screws.

NOTE: Spacers may not be used, depending upon

the type of display.

Skip to step 2-5.

Begin with the longest length screw, hand thread

screw through multi-washer, display brackets (B)

and spacer in that order into display as shown

below. Screw must make at least three full turns

into the mounting hole and ﬁt snug into place.

Do not over tighten. If screw cannot make three

full turns into the display, select a shorter length

screw from the bafﬂed fastener pack. Repeat for

remaining mounting holes, level display brackets

and tighten screws.

For Flat Back Display

For Bump-out or Recessed Back Display

2-3

2-4

DISPLAY

MULTI-WASHER

SCREW

DISPLAY

MULTI-WASHER

SPACER

SCREW

Center display brackets horizontally and vertically

on back of display. Tighten two 1/4-20 x 1.25"

screws. Reinstall four 1/4-20 x .6" screws using

5mm allen wrench (I) into appropriate ﬁxed-stop

position from chart on page 7.

2-5 1/4-20 x 1.25" SCREWS

1/4-20 x .6" SCREWS

10 of 58 ISSUED: 10-30-09 SHEET #: 095-9297-8 11-01-11

Remove four 1/4-20 self tapping screws to detach display brackets from outer mount holes of universal adapter

bracket (B) using 5mm allen wrench (I) as shown in ﬁgure 3.1. Reinstall four 1/4-20 self tapping screws to secure

display brackets to inner set of mounting holes on universal adapter bracket (B) as shown in ﬁgure 3.2.

1/4-20 SELF

TAPPING SCREWS 1/4-20 SELF

TAPPING SCREWS

Display

BRACKETS Display

BRACKETS

INNER

MOUNTING

HOLES

OUTER

MOUNTING

HOLES

ﬁg. 3.1 ﬁg. 3.2

VESA 200 x 200 or VESA 200 x 100 Mounting Pattern

To prevent scratching the display, set a cloth on a

ﬂat, level surface that will support the weight of the

display. Place display face side down and place

universal adapter bracket (B) onto display.

3-1

1/4-20 x .6" SCREWS

1/4-20 x 1.25" SCREWS

Remove four 1/4-20 x .6" screws using 5mm allen

wrench (I) and loosen two 1/4-20 x 1.25" screws 1/2

turn to allow for display bracket adjustment.

Other manuals for SA752PU

Table of contents

Languages:

Other peerless-AV Rack & Stand manuals

peerless-AV

peerless-AV CMJ500R1 User manual

peerless-AV

peerless-AV SF632-S User manual

peerless-AV

peerless-AV ESF686 User manual

peerless-AV

peerless-AV SmartMount SF640-HUB2 User manual

peerless-AV

peerless-AV KIL642 User manual

peerless-AV

peerless-AV EXT User manual

peerless-AV

peerless-AV Paramount PF630 Guide

peerless-AV

peerless-AV KIP586-3LG-EUK User manual

peerless-AV

peerless-AV SR584VL2 User manual

peerless-AV

peerless-AV SMARTMOUNT WSP756 User manual

peerless-AV

peerless-AV PPA User manual

peerless-AV

peerless-AV LCW620AD Guide

peerless-AV

peerless-AV MOD-FCS2KIT300 User manual

peerless-AV

peerless-AV EXT101 User manual

peerless-AV

peerless-AV DS-MBY947L-3X1 User manual

peerless-AV

peerless-AV PLCK-UNL Guide

peerless-AV

peerless-AV PR560M User manual

peerless-AV

peerless-AV MOD-FPMD2 User manual

peerless-AV

peerless-AV PA762-UNMH User manual

peerless-AV

peerless-AV LCV-100 Guide

peerless-AV

peerless-AV ST650-AB User manual

peerless-AV

peerless-AV DS-VWC555-3x2 Guide

peerless-AV

peerless-AV ACC925 User manual

peerless-AV

peerless-AV ACC570 User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

peerless-AV SA752PU Guide

Popular Rack & Stand manuals by other brands