Parkmate CMD-14N Instruction Manual

WIDE ANGLE REVRESE CAMERA

with GRID-LINES & FLIP IMAGE

INSTALLATION / USER MANUAL

MODEL: CMD-14N

www.parkmate.com.au

Thank you for purchasing Parkmate’s CMD-14N camera. We are certain that our product will

give you trouble-free operation while providing you with a safety feature that enhances your

driving experience.

Our products, like most after-market safety enhanced devices, are to assist and aid the driver,

not to replace the manual function of the person operating the vehicle.

Although this is a visual aid and will allow you to view what is behind the vehicle, it does not

remove the responsibility of driving the vehicle from the driver. The legal responsibility and

safe driving practise remains with the driver at all times. You have purchased this product

with the understanding that its use is as an aid only. We highly recommend that you have

this product professionally installed to ensure that it will provide the functions it is set out to

perform.

CMD-14N

Component List:

Notes:

• Please read this manual carefully before using the product.

• This system is intended as an aid to safe reverse operation. Drivers must always use

extreme caution when operating a vehicle.

• Speciﬁcations subject to change without prior notice.

Warning:

• Do not disassemble the camera or cut the camera cable as this voids the warranty.

Disassembling the camera will compromise the waterproof seal.

• Do not remove the Directed warranty sticker as this voids warranty.

Technical Speciﬁcations: Wiring Diagram:

Signal System: NTSC

Horizontal Resolution: 550TVL

Minimum Illumination: 0.2Lux

Diagonal Angle: 170°

Waterproof Grade: IP67

Nominal Voltage: DC12V

Working Temp.: -20°C to 85°C

Front view option: CMD-14N functions as a rear view

camera standard and also supports front view. For front

view application, you can cut the thin WHITE wire near the

camera lead and restart power to see the image reversed.

Grid-Line option: CMD-14N has parking grid-lines as a

default. To remove grid-lines, cut the thin GREEN wire

near the camera lead. Power on and the grid-lines will

now be removed.

camera

bumper adaptor

hole saw

3M tape

power harnessscrews 6m video cable

splitter cable

RED to Reversing Light +

BLACK to Ground

Switching Wire

Monitor Video Input

video extension cable

Installation - Butterﬂy Mount

1. Select a ﬂat and centred location

near the number plate lamp at the

rear of the vehicle to mount camera.

IMPORTANT: When selecting this location it is highly recommended that the image transmitted

by the camera show the rear bumper and area behind the vehicle.

Installation - Flush Mount

1. Unscrew the upper part of

the camera anticlockwise,

detach the upper part and

bracket, and place the

bumper adaptor instead.

2. Attach the 3M tape to the

bracket of the camera, and

drill a small hole for the

ﬁrst screw.

3. Use a screw driver to ﬁx

the ﬁrst screw, but don’t

tighten it yet.

4. Insert camera wire through

newly drilled hole and

mount securely in place.

5. Mark the position suitable

for the second screw and

drill a small hole for it.

6. Fix the second screw and

tighten both screws.

4. Pull the camera lead

through the bumper hole

before ﬁxing the camera.

5. Put the camera into the

hole and use both your

thumbs to press it evenly

to ensure tight and ﬂat

mounting.

2. Mark the middle position

of rear bumper, and drill

a hole with the provided

16.5mm hole saw.

3. Adjust the camera to turn

the UP arrow straight

up-wards.

Suggested location

to mount camera

Testing

How to test:

1. Apply the parking brakes. (Saftey Precaution)

2. Turn Ignition on. (DO NOT TURN ON VEHICLE)

3. Shift into reverse gear.

4. Image should appear on the monitor.

Trouble Shooting:

Maintenance:

Always keep camera clear from dirt and mud. Clean camera with a soft moist cloth.

Australian Residents - Warranty Terms & Conditions:

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and for compensation for

any other reasonably foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and the failure does not

amount to a major failure.

This warranty is provided in addition to your rights under the Australian Consumer Law.

Directed Electronics warrants that this product is free from defects in material and

workmanship for a period of 12 months from the date of purchase or for the period stated on

the packaging. This warranty is only valid where you have used the product in accordance

with any recommendations or instructions provided by Directed Electronics.

This warranty excludes defects resulting from alterations of the product, accident, misuse,

abuse or neglect.

In order to claim the warranty, you must return the product to the retailer from which it was

purchased or if that retailer is part of a National network, a store within that chain, along with

satisfactory proof of purchase. The retailer will then return the goods to Directed Electronics.

Directed Electronics will repair, replace or refurbish the product at its discretion. The retailer

will contact you when the product is ready for collection. All costs involved in claiming this

warranty, including the cost of the retailer sending the product to Directed Electronics, will be

borne by you.

Directed Electronics Address: 44 Translink Drive, Keilor Park Victoria Australia 3042

Ph: +61 03 8331 4800

Email: [email protected]

To view the complete Parkmate range or for details on how to contact us, please visit our

website at www.parkmate.com.au

Problem Solution

“No Signal” appears while reversing 1. Check video input connections

2. Check camera power connections

Video image is not sharp Check camera lens for debris

Parkmate CMD-14N Instruction Manual

Popular Car Video System manuals by other brands