Parker DINCon II Assembly instructions

Parker DINCon II, DINPres II,

& DINTemp II Modules

Installation, Operating & Maintenance Instructions

Parker Hannifin Corporation has a continuous policy of product development and although the Company reserves the right to

change specification, it attempts to keep customers informed of any alterations. This publication is for general information only and

customers are requested to contact your local Parker Sales Representative for detailed information and advice on a product’s

suitability for specific applications. All products are sold subject to the company’s Standard conditions of sale.

DINCon II™ DINPres II™ and DINTemp II™ are registered trademarks of Parker Hannifin Corporation.

Contents

Introduction ................................................................................................................................. 6

Calibration .................................................................................................................................. 6

Warranty ..................................................................................................................................... 7

Standards ................................................................................................................................... 7

Installation & Start-Up ................................................................................................................. 7

Maintenance & Cleaning ............................................................................................................. 7

DIN II Module Specifications ....................................................................................................... 8

Installation ................................................................................................................................ 11

Operating Instructions............................................................................................................... 14

Modbus Register List ................................................................................................................ 16

DINCon II Registers .................................................................................................................. 16

DINPres II Registers ................................................................................................................. 20

DINTemp II Registers ............................................................................................................... 25

Revision History:

Rev. # Date Author Description

A 4/25/2019 A. Dawson Initial release, based on original SciLog DIN Module

Manual

Precautions

READ this manual BEFORE operating or servicing this equipment.

FOLLOW these instructions carefully.

SAVE this manual for future reference.

DO NOT allow untrained personnel to operate, clean, inspect, service or tamper with

this equipment.

ALWAYS DISCONNECT this equipment from the power source before cleaning or

performing maintenance.

Contact your local Parker Division for parts, information and service.

WARNING

DISCONNECT ALL POWER TO THIS UNIT BEFORE INSTALLING,

SERVICING, CLEANING OR REMOVING THE FUSE. FAILURE TO DO

SO COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.

CAUTION

OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC

SENSITIVE DEVICES.

WARNING

ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS

EQUIPMENT. EXERCISE CARE WHEN MAKING CHECKS, TEST AND

ADJUSTMENTS THAT MUST BE MADE WITH POWER ON. FAILING TO

OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY HARM.

WARNING

FOR CONTINUED PROTECTION AGAINST SHOCK HAZARD, CONNECT

TO PROPERLY GROUNDED OUTLET ONLY. DO NOT REMOVE THE

GROUND PRONG.

CAUTION

USE ONLY CLASS 2 LISTED EXTERNAL 24 VDC POWER SUPPLY WITH

THESE DEVICES.

Précautions

LISEZ ce manual AVANT de faire fonctionner ou d’entretenir cet équipment.

SUIVEZ attentivement ces instructions.

CONSERVEZ ce manuel pour future référence.

NE LAISSEZ PAS du personnel non qualifié utiliser, nettoyer, inspecter, entretenir, réparer ou

manipuler cet équipement.

DÉBRANCHEZ TOUJOURS cet équipement de la source de courant avant de nettoyer ou

d’exécuter l’entretien.

APPELEZ PARKER pour pièces détachées, renseignements et entretien.

ATTENTION

DÉBRANCHEZ TOUT COURANT DE CETTE UNITÉ AVANT DE FAIRE

L’INSTALLATION, D’EFFECTUER L’ENTRETIEN, LE NETTOYAGE OU

AVANT DE RETIRER LE FUSIBLE. NE PAS OBSERVER CES

PRÉCAUTIONS RISQUERAIT DE CAUSER DES BLESSURES

CORPORELLES OU/ET D’ENDOMMAGER L’

QUIPEMENT.

PRUDENCE

SOYEZ PRUDENT LORSQUE VOUS MANIPULEZ DES APPAREILS

SENSIBLES À L’ÉLECTROSTATIQUE.

ATTENTION

ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS

EQUIPMENT. EXERCISE CARE WHEN MAKING CHECKS, TEST AND

ADJUSTMENTS THAT MUST BE MADE WITH POWER ON. FAILING TO

OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY HARM.

ATTENTION

POUR ASSURER UNE PROTECTION CONTINUE CONTRE UNE

DÉCHARGE ÉLECTRIQUE, BRANCHEZ UNIQUEMENT SUR UNE PRISE

CORRECTEMENT RELIÉE Á LA TERRE. NE RETIREZ PAS LA FICHE DE

TERRE.

PRUDENCE

N'UTILISER QUE DE L'ALIMENTATION ÉLECTRIQUE 24 VDC

EXCLUSIVE DE CLASSE 2 AVEC CES DISPOSITIFS.

Introduction

You will find the DINCon II, DINPres II and DINTemp II Modules and sensors easy to use. The state-of-

the-art hardware and software design of the DIN Module and sensor combination allows you to

measure and document the conductivity, pressure or temperature of many filtration / separation

processes. With proper maintenance, the DIN II Modules will provide many years of excellent service

and performance.

Please read the following instructions carefully!

Inspections: Remove the products carefully from the shipping container. Check the contents against

the purchase order to verify that all parts are included and undamaged.

Please do the inspection now, even if the products are not used immediately. Many carriers must

receive damage claims within seven days of delivery. Please retain all packing material so unit may be

shipped safely, if necessary.

Customer Service:

Parker Hannifin Corporation

Bioscience Filtration Division

2340 Eastman Avenue

Oxnard, California, USA 93030

toll free: 877 784 2234

phone: +1 805 604 3400

fax: +1 805 604 3401

email: [email protected]

www.parker.com/bioscience

Parker Hannifin Manufacturing Ltd

Bioscience Filtration Division

Durham Road

Birtley, Co. Durham

DH3 2SF, England

phone +44 (0)191 4105121

fax +44 (0)191 4105312

email: [email protected]

www.parker.com/bioscience

Parker customer service personnel will be able to serve you more efficiently if you have the following

information:

 Serial number and model name of the equipment

 Installation procedure being used

 Concise list of symptoms

 List of operating procedures and conditions in use when problem arose

Calibration

The DIN II Modules are calibrated devices and are calibrated with test equipment that is traceable to SI

through NIST.

A Calibration Certificate is included with each unit and has a one year expiration date.

It is highly recommended that the Module be calibrated on an annual basis or more often if your

Metrology Department deems it necessary.

Parker Bioscience Filtration provides this Calibration Service, complete with a new certificate, showing

the “as found” and “as left” data.

Contact your local Parker Bioscience Filtration Territory Manager if a quote is needed for this service.

Onsite calibration can be arranged.

Warranty

Country specific information can be found at: www.parker.com/termsandconditions

Standards

EN 61326-1:2006, Class B

EN 61010-1:2010 Ed.3+ C1; C2

Conforms to UL STD 61010-1:2012 Ed.3+ R: 29Apr2016

Certified to CSA STD C22.2 No 61010-1-12:2012 Ed.3+U1;U2

Caution: The maximum recommended pressure for the sensors is 60 psi.

If this is exceeded, problems with leakage and functionality can occur.

Installation & Start Up

Installation of the DINCon

II, DINPres

II, and DINTemp II Modules must be carried out only by trained

personnel in accordance with the relevant regulations and this operation manual.

Make sure that the technical specifications and input ratings of the single-use sensors are observed.

See the appropriate Sensor Specifications page.

The protection provided by this equipment may be impaired if the single-use sensors are used in a

manner inconsistent with this manual or for purposes not specified by the manufacturer.

Maintenance & Cleaning

The Parker DIN II Modules are maintenance free. The single-use Parker sensors come pre-calibrated

from the factory and require no maintenance.

To remove dust, dirt and stains, the outer surfaces of the DIN II Modules may be wiped using a soft,

non-fluffing cloth moistened with water. If required, you may also use a mild detergent or 2-propanol.

The single-use sensors may be sanitized with 0.1 Molar NaOH, or 2-propanol. They may be autoclaved

up to 2 times, or gamma-irradiated with exposure up to 45 kGy.

Hardware

Specifications – All Modules

Dimensions W: 0.875¨ (2.2 cm); Height 4.0¨ (10.2 cm); D: 4.75¨ (12.1 cm)

Weight 0.3 lb. (0.14 Kg)

Enclosure Molded Plastic

Electrical

Power 24 VDC, 250 mA. Use only Class 2 External Power Supply

Battery CR1216, used for internal clock, not user serviceable

I/O Port Top 8 pin Terminal Block, numbered from rear:

1: +24 VDC 2: 24 VDC Return 3: N/C 4: Signal GND (COM)

5: RS-232 RX 6: RS-232 TX 7: RS-485 A 8: RS-485 B

I/O Port – 2 RJ45, Ethernet Connection

I/O Port - 3 USB Connection

Software

I/O Port

Bottom

14 Pin Sensor Connection, DINCon has 1, DINPres and

DINTemp have 3.

DISPLAY Power Status LED, Sensor Status LED’s

Modbus Modbus RTU via RS-232

Modbus RTU via RS-485

Modbus RTU via USB

Modbus TCP via Ethernet

Environmental

Temperature 4 – 60° C

Altitude Up to 2000 Meters

IP Rating IP20, Indoor dry environments, unit is wipe-down only

Rel. Humidity 0 – 95%

Voltage Fluctuation allowed: +/- 10%

Pollution Degree: 2

Installation

Overview:

The DINCon II, DINPres II, and DINTemp II Modules are designed to be installed as

part of a control system inside a control cabinet that has a 24 VDC source available and

has Modbus communication protocol capability.

The DIN II Modules are installed on standard DIN II rail. They are usually mounted with

the red locking tab located at the bottom of the unit. This places the Power and

Communication connections at the top of the Module and the Sensor connections at the

bottom. They may be mounted upside-down if that proves useful.

Wiring Power and Communication:

Connect 24 Volts DC, 250 mA power to Pins 1 (+) and 2 (-) of the 8 pin terminal block.

(Note - pin 1 is at the rear, nearest the DIN rail.)

All data acquisition is via Modbus registers in either RTU or ASCII. The available

physical layers are RS-232, RS-485, Ethernet and USB. The recommended physical

layer for installation of multiple units is Modbus/RTU over RS-485 with Modbus/TCP via

Ethernet a close second.

For RS-232, connect to the following: Pin 4 = Signal Ground, Pin 5 = RX, Pin 6 = TX.

For RS-485, connect to the following: Pin 7 = RS485-A, Pin 8 = RS485-B.

For Ethernet connect an Ethernet cable to the provided RJ45 jack.

For USB connect to the provided USB Type A jack.

Pin 1: +24VDC

Pin 2: Common

Pin 3: Not Connected

Pin 4: Si

nal Ground

Pin 5: RS-232 RX

Pin 6: RS-232 TX

Pin 7: RS-485

Pin 8: RS-485 B

USB

RJ45 Ethernet

DIN

Rail

Connecting Sensors:

All sensors, SciCon II for use with the DINCon II Module, SciPres II for use with the

DINPres II Module, and SciTemp II for use with the DINTemp II Module are disposable

flow through sensors that are purchased separately from Parker and come pre-

calibrated.

The sensors connect to a provided cable that has an Amphenol bulkhead watertight

connector on the sensor end and a 14 pin connector on the other end that plugs into a

matching port on the bottom of the Module. The DINCon II has only one port, and uses

only one SciCon II Sensor. The DINPres II and DINTemp II have 3 ports, can support

up to 3 SciPres II or SciTemp II Sensors, and they are referred to as P1 – P3 or T1 – T3

beginning with P1 and T1 at the rear, or the closest connector to the DIN rail. These

cables are 12” long providing flexibility in where the bulkhead fittings are installed on the

control cabinet.

These cables ship with a ferrite clamp included that should be attached and secured to

the cable as shown below: (anywhere along the cable is fine.)

Sensor 1

Sensor 2

Sensor 3

DIN II Rail locking clip

This manual suits for next models

Table of contents

Other Parker Control Unit manuals

Parker

Parker EBV-PR Series User guide

Parker

Parker D Series User manual

Parker

Parker 71215 User manual

Parker

Parker P33 Quick setup guide

Parker

Parker PA Series Assembly instructions

Parker

Parker Vansco VMM1210 User manual

Parker

Parker Sporlan B5D Series User guide

Parker

Parker S5A Guide

Parker

Parker HASV08R User manual

Parker

Parker PIO-400 User manual

Parker

Parker SC Series Reference manual

Parker

Parker S6N-DN User manual

Parker

Parker H Series User manual

Parker

Parker S7A Service manual

Parker

Parker VA01 Series User manual

Parker

Parker D*1VW*EE Series User manual

Parker

Parker PID00A-40 Series User manual

Parker

Parker U131B01 Assembly instructions

Parker

Parker AC30V Series User manual

Parker

Parker Sporlan SD-114 User guide

Parker

Parker D*1VW*EE Series User manual

Parker

Parker D 1FC Series User manual

Parker

Parker C6 Series Installation and maintenance instructions

Parker

Parker PSSTACM12A Installation and maintenance instructions

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual