Paradigm Decor 2S User manual
Paradigm DOES NOT supply hardware for
mounting speakers to the wall. Always use
screws appropriate for wall type and weight
of speakers.
Wall mount your speakers securely
enough that they cannot fall and cause
personal injury or damage to property.
NON LIABILITY: We are aware that the mounting
assemblies provided for speakers in this manual could be
used for purposes and in ways other than those for which
they were intended. The manufacturer, distributor, retailer
and their respective agents cannot be held responsible
or liable for injuries or property damage—direct, indirect
or consequential—arising from the use of or inability to
use these products safely and properly. Every effort has
been made to provide accurate, error-free installation
instructions. Paradigm Electronics Inc. disclaims liability
for difficulties that may arise from the misinterpretation
of information contained in these instructions.
An Important Note About TV Mounting Bracket:
Ensure the TV mounting bracket, attached to the wall, will accommodate
the extra weight of the Décor speakers and Décor Mounting Rails BEFORE
attaching to wall. If unsure, consult dealer or TV mount manufacturer.
2SC
2S
CAUTION: 2 PERSON
INSTALLATION
Instructions for VERTICAL
55” to 88” TV Mounting Bracket
(4) SPEAKER
BRACKETS
(4) RAIL
BRACKETS
(4) SLIDING
RAILS
(2) FIXED
RAILS
CC
AA
Z
DD
(1) 7/64” HEX
ALLEN KEY
(1) 5/32” HEX
ALLEN KEY
(4) HINGES
W
X
Y
(8) SMALL
SPLIT WASHERS
(8) LARGE
M6 WASHERS (8) SPACERS
(6) M6-NUTS
(8) LARGE
M8 WASHERS
(8) SPLIT
WASHERS
A
B
C
D
E
F
(6) M8-NUTS
(4) 1/4”-20 NUTS
(8) #6-32 x 5/8”
SCREWS
(8) #12-24 x 1/2”
SCREWS
(8) #12-24 x 1-3/4”
SCREWS
(4) M6-35mm
SCREWS
K
M
I
J
G
H
(4) M8-50mm
SCREWS
(2) M6-85mm
THREADED RODS
(2) M8-85mm
THREADED RODS
R
U
V
(4) M8-35mm
SCREWS
(4) M6-50mm
SCREWS
N
Q
HARDWARE INCLUDED (KIT0081 or KIT0082)
Depending on TV type, not all hardware listed will be required.
RAIL ASSEMBLIES
CAUTION: THIS IS A TWO PERSON PROCEDURE. TWO PEOPLE ARE NEEDED TO
CARRY OUT THE INSTRUCTIONS OUTLINED BELOW. BE CAREFUL NOT TO DAMAGE
TV AND SPEAKER DRIVERS DURING BRACKET INSTALLATION.
Before installing, identify TV profile type (A, B or C) and gather the necessary
mounting hardware required from the contents provided.
(4) M6-50mm Screws (N)
OR (4) M8-50mm Screws (R)
(4) M6-Washers (C)
OR (4) M8-Washers (D)
(8) Spacers (E)
(2) Railing Assemblies (see step 1)
(4) M6-35mm Screws (M)
OR (4) M8-35mm Screws (Q)
(4) M6-Washers (C)
OR (4) M8-Washers (D)
(2) Rail Assemblies (see step 1)
(2) Threaded Rods M6-85mm (U)
OR (2) Threaded Rods M8-85 (V)
(2) M6-35mm Screws (M)
OR (2) M8-35mm Screws (Q)
(8) M6-Washers (C)
OR (8) M8-Washers (D)
(6) M6-Nuts (F)
OR (6) M8-Nuts (G)
(2) Rail Assemblies (see step 1)
(B) PROFILE TV (4 screw holes at base of TV)
(C) PROFILE TV (2 screw holes TOP and BOTTOM)
(A) CURVED or SLIM or PROFILE TV (4 screw holes at TOP of TV)
MOUNTING PROCEDURE
K
J
B
YZ
CC
DD
C
AA
B
K
J
Z
C
H
Y
AA
CC
DD
1. Lay TV facedown, on floor. Position Décor SPEAKER AND GRILLE along side edges
of TV. Be careful not to damage the screen or the speaker drivers. Be sure to position
speaker with terminals away from TV.
NOTE: Be sure to move speaker and grille together when positioning against TV.
Vertical speaker mounting rails, with hinges, have been preassembled. Image below
shows preassembled parts and hardware, in exploded view.
3. If TV is (A) CURVED or SLIM or PROFILE, eight spacers (E) are provided to make TV
“flush” with speaker. See diagram below.
4. Take additional TV rails included in separately purchased TV wall Mount Kit and
place onto back of TV overtop of attached speaker rail assemblies.
E
R
D
OR
OR
Décor Mounting
Rail Assemblies
N
C
TV Mounting
Brackets
(Purchased
Separately)
(A) CURVED or SLIM or PROFILE TV (4 screw holes at TOP of TV)
I
A
If TV or TV
protrusion is
thinner than speaker,
spacers or washers
are required under
Décor mounting rails.
2. Place speaker rail assemblies on back of TV and align holes on rails to holes
on back of the TV. Ensure center of Décor Fixed Mounting Rail is centered to
width of TV.
Q
Q
V
G
D
D
D
OR
OR
OR
OR
OR
OR
OR
M
U
F
C
C
C
WASHER ON PART “U” OR “V”
TO BE SET ON SAME LEVEL
WITH TV REAR PROTRUSION
M
(B) PROFILE TV (4 screw holes at base of TV)
(C) PROFILE TV (2 screw holes TOP and BOTTOM)
5. Secure Décor Speaker rails and TV mounts, as shown on previous pages, using washers
and screws. DO NOT TIGHTEN SCREWS AT THIS STAGE.
6. Attach speaker brackets (Z) to speaker using washers (A) and screws (I).
7. Ensure speakers are properly aligned with TV before tightening all screws
and threaded rods with nuts (F) or (G) if applicable, only when using threaded
rods (U) or (V). Now, tighten screws securely.
At this stage, mounting system is now ready to be installed on wall.
Follow instructions which came with your TV mount to place TV on wall.
CAUTION: CAREFULLY LIFT BY RAILS. DO NOT LIFT BY TV EDGE.
Support entire bracket assembly and place onto TV Mount on wall
(purchased separately). Follow TV Mounting instructions. WHEN RE-
HANGING TV, SUPPORT BOTH THE TV AND THE ATTACHED SPEAKERS.
Fine Adjustments:
After hanging TV, according to manufactures bracket instructions, adjust speaker to be
flush with TV. Use Allen Key to secure tightly.
A
I
Z
Channel in speaker
back used to drive
bracket screws
MAN0165 REV2
To ensure proper installation and enjoy all of the exceptional sound these speakers
are designed to provide, please read this manual and follow all instructions.
Paradigm Electronics Inc., 205 Annagem Blvd., Mississauga, ON L5T 2V1
T: +1 905.564.1994
This manual suits for next models
1
Table of contents
Other Paradigm TV Mount manuals
