Panasonic WV-Q118E User manual
FEATURES
Wall Mount Bracket
Instructions
Model No. WV-Q118/WV-Q118E
PLACES OF INSTALLATION
AF0205-6012 3TR003444GAA Printed in Japan
Wall box
●Wall Box
Wood Siding Board
Strong enough to support the
camera weight
(approx. 3 kg{6.60 lbs})
●Wood Siding Board
Concrete slab Concrete slab
●Concrete
Template
(provided)
Wall
1Make four holes in the wall using the template
(provided).
Protection Cover
(provided)
Part to be cut
2Wrap the camera cables with the Protection
Cover (provided) as appropriate to the
Diecast Case.
INSTALLATION
Cut here
4Cut the Diecast Case as shown.
Note: Be sure to protect the Video and Power
Cables with the Protection Cover
(provided).
Mounting
Screw
Rotate 15°
Remove the Camera Mounting
Base by pulling up.
3Remove the Mounting Screw (M3, provided),
pull up the Camera Mounting Base off the
camera, and turn the camera counterclock-
wise.
Wall mounting bracket:
Attach the wall bracket to a concrete or other stur-
dy wall to install the combination camera.
There are various ways of installing the camera as shown below.
Before attempting to connect or install this product,
please read these instructions carefully and
save this manual for future use.
The model number is abbreviated in some descrip-
tions in this manual.
• Fasten the bracket to a ceiling strong enough
to support the camera weight (approx. 3
kg.{6.60 lbs}).
• Wipe the bracket regularly using a soft and
dry cloth, or a cloth moistened with a water
solution of an ordinary kitchen detergent.
• Do not use chemicals for cleaning the enclo-
sure as it may damage the surface.
• All the necessary steps required for installing
this product must be taken by a qualified ser-
vice person or system installer.
PRECAUTIONS
• Be sure to use the Fall Prevention Wire.
• Do not use this bracket except with suitable
cameras.
• Follow all applicable local and national elec-
trical, fire and safety codes when installing
the camera with this ceiling mount bracket.
The model numbers in this Operating Instruc-
tions are shown without suffix.
Decoration cover (1)
Decoration cover (2)
5Remove the Decoration Cover in order (1)
then (2).
The Decoration Cover can be removed by
pressing on the points (1) at one place, and
(2) at 4 places.
6Fix the Camera Mounting Base (provided with
the camera) to the bracket with the four M4-
L8 Screws (provided).
Recommended tightening torque: 1.56 N·m
{1.16 lbf·ft}
Note: Be sure to fix the Camera Mounting Base in
the up direction as shown.
Clamp
7Run the cable around the outside and secure
it with the clamp.
Secure the cable with the clamp so it goes
along the inside of the top case so it does not
get in the way when attaching the case and
installing the camera.
8Attach the top case to the wall and run the
cables.
Attach it with four screws. Screws are not
provided. Align it with the position the camera
will be installed.
Decoration cover (2)
9Place the removed Decoration Cover(2) back
on the bracket and camera.
Note: Push the Decoration Cover up till it fits
over the bracket with a click.
Ring of the Fall
Prevention Wire
10 Suspend the Fall Prevention Wire from the
Camera Mounting Base.
Notes:
• Make sure that the wire matches the Fall
Prevention Wire Fixing Angle.
• The bracket is not shown in the illustration.
15°
Camera
Mounting
Base
Camera
Rotate
Press up
11 Attach the camera to the Camera Mounting
Base, turn the camera clockwise, and tight-
en the Mounting Screw (M3, provided).
Recommended tightening torque: 0.68 N·m
{0.51 lbf·ft}
Notes:
• Tigthen the Camera Fixing Screw with a
screwdriver.
• In attaching the camera to the Camera
Mounting Base, loosen the Camera Fixing
Screw (M3), then tighten it back with a screw-
driver while keeping it pushed up.
• The bracket is not shown in the illustration.
Decoration cover (1)
12 Place the removed Decoration Cover (1)
back on the bracket and camera.
Note: Push the Decoration Cover up till it fits over
the bracket with a click.
Ambient Operating Temperature: 10˚C - +50˚C {14˚F – 122˚F}
Dimensions: 165 (W) x 140 (H) ×217.5 (D) mm
{6-1/2” (W) x 5-33/64” (H) ×8-37/64” (D)}
Weight: 650 g{1.43 lbs}
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS
STANDARD ACCESSORIES
Screw (M4-L8) ..................................................... 4 pcs.
Screw (M4-L4) ..................................................... 4 pcs. (spare)
Template ................................................................. 1pc.
Protection Cover ..................................................... 1pc.
This manual suits for next models
1
Other Panasonic TV Mount manuals
Panasonic
Panasonic i-PRO WV-Q117A User manual
Panasonic
Panasonic ET-PKL300B User manual
Panasonic
Panasonic TY-WK42PV4W User manual
Panasonic
Panasonic WV-Q204/1 User manual
Panasonic
Panasonic BB-HCA11A User manual
Panasonic
Panasonic TY-ST32PE1 User manual
Panasonic
Panasonic ET-PKE2000 - Mounting Kit For Projector User manual
Panasonic
Panasonic ET-PKD120S User manual
Panasonic
Panasonic TY-ST50VX100 User manual
Panasonic
Panasonic WV-Q185 User manual
Panasonic
Panasonic TY-WK32LX20W User manual
Panasonic
Panasonic ET-WBC100 User manual
Panasonic
Panasonic TY-WK42PV3U User manual
Panasonic
Panasonic ET-PKL6500 User manual
Panasonic
Panasonic TY-WK32LR2W User manual
Panasonic
Panasonic ET-PKL430B ET-PKL100S User manual
Panasonic
Panasonic TY-WK3L1RW User manual
Panasonic
Panasonic WV-QJB502-W User manual
Panasonic
Panasonic TY-CE103PS10 User manual
Panasonic
Panasonic TY-WK5P1RW User manual
