Panasonic WV-Q126 User manual

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

Operating Instructions

Ceiling Mount Bracket

Model No. WV-Q126

CONTENTS

Preface ...................................................................................................................................... 2

Precautions ................................................................................................................................ 2

Major Operating Controls .......................................................................................................... 4

Installations ................................................................................................................................ 5

Specifications ............................................................................................................................ 12

Standard Accessories ................................................................................................................ 12

Precautions

Refer installation work to the dealer.•

Installation work requires technique and experiences. Failure to observe this may cause fire,

electric shock, injury, or damage to the product. Be sure to consult the dealer.

Avoid installing this bracket in the locations where salt damage occurs or corrosive•

gas is produced.

Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera

may occur.

Use only the specified camera.•

Failure to observe this may cause a fall of an inappropriate camera resulting in injury or acci-

dents. Refer to the catalog or the installation guide of the camera for supported cameras.

The screws and fixation mechanisms shall be tightened securely.•

Failure to observe this may cause a fall of the camera resulting in injury.

The measures of protection against a fall of the camera shall be taken.•

Failure to observe this may cause injury. Be sure to install the safety wire.

Select an installation area that can support the total weight.•

If a selected area is too weak to support the total weight, a fall of the product may occur result-

ing in injury. Installation work shall be started after sufficient reinforcement.

Preface

This ceiling mount bracket is exclusively designed to mount the camera on a ceiling. Refer to the

catalog or the installation guide of the camera for supported cameras.

This bracket can be used for an area with weak pull-out strength such as plasterboard in a double

ceiling.

This bracket is an embedded type to reduce the exposed portion of the camera body.

Periodic inspections shall be conducted.•

Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult the

dealer for the inspections.

Do not rub the edges of metal parts with your hand.•

Failure to observe this may cause injury.

Consult the dealer about the installation area to select a strong ceiling area. Make sure that the•

installation area is strong enough to hold the total weight of the camera assembly (approx. 2.8 kg

{6.13 lbs.}) before installation.

The installation area shall have 210 mm {8-9/32"} or more space behind the ceiling.•

210 mm {8-9/32"} or more

Ceiling board: between 9 mm {3/8"}

and 40 mm {1-9/16"}

The thickness of the ceiling board for installation can range between 9 mm {3/8"} and•

40 mm {1-9/16"}.

Avoid installing in the following locations.•

Locations where it may get wet from rain or water splash (not only outdoor)•

Locations where a chemical agent is used such as a swimming pool•

Locations subject to steam and oil smoke such as a kitchen•

Locations near flammable gas or vapor•

Locations where radiation or x-ray emissions are produced•

Locations subject to strong magnetic field or radio waves•

Locations where it may be damaged by briny air such as seashores•

Locations where the temperature is not within -10 C- + 50 C {14 F - 122 F}.•

Locations subject to vibrations (This product is not designed for on-vehicle use.)•

Locations where the temperature may rapidly change such as the peripheral areas of the air•

outlets of air conditioners or doors facing outside. (In case of installing the camera in such

locations, the dome cover may become foggy or condensation may be caused on the

cover.)

The screws and bolts must be tightened with an appropriate tightening torque according to the•

material and strength of the installation area. After tightening the screws or bolts, perform visual

check to ensure tightening is enough and there is no backlash.

Major Operating Controls

Safety wire angle (Accessory)

Safety wire (Accessory)

Decorative cover

Ceiling mount bracket

Camera

Ceiling board

Roof space

Decorative cover

Camera mounting stage

Mounting chassis

Installations

Be sure to read "Precautions" before installation. The Installation Guide of the camera shall be read

as well.

Put Template A (accessory) against the1.

ceiling and make a hole.

Make 4 holes of 12 mm {1/2"} in diameter.1

Remove the center part from the tem-2

plate.

Make a hole of 220 mm {8-43/64"} in3

diameter.

ø12 mm {1/2"}

(4 positions)

Ceiling face

ø220 mm

{8-43/64"}

Template A

* 1 The hole shape is shown below.

[

For those concerned with the direction of

the brand logo]

In order to set the position of the brand

logo on the decorative cover you installed

in Step 14 at the 12 mm hole, you must

perform the required operations during

Step 1.

Perform Step 1to make sure the desired

brand logo direction matches the "Brand

logo side" setting on Template A. Also

pay attention to this setting when per-

forming Step 6 later.

Install two anchor bolts (M10 recommended) into the concrete ceiling.2.

Determine the anchor bolt length by use of Template B (accessory).1

Position the nut by use of Template B (accessory). (The distance between the bottom sur-2

faces of the ceiling board and nut shall be 169 mm {6-21/32"}.)

Template B

Ceiling board

Install the anchor bolt in the center of the hole

Determine the anchor bolt length

169 mm {6-21/32"}

Use a nut

Anchor bolt

Note: If there is already an anchor bolt installed, the anchor bolt can be used as a second

anchor bolt. Make sure that the distance between the 1st and 2nd anchor bolts is 1 000

mm {39-3/8"} or less before use.

3. Mount the safety wire angle (accessory) on the 2nd anchor bolt and connect the safe-

ty wire (accessory) to the angle.

Disconnect the safety wire from the1

safety wire angle.

Engage the face marked2 1with the

anchor bolt.

Bend the face marked3 2.

Connect the safety wire to the safety4

wire angle again.

Note: To use the anchor bolt that was already installed, the use of 2 spacer nuts is helpful.

Spacer nuts

Safety wire Spacer nuts

Safety wire angle

Existing anchor bolt

4. Remove the camera mounting stage.

Remove the 6 screws (M4).1

Rotate the camera mounting stage2

a half-turn clockwise.

Lift the camera mounting stage and3

remove it.

Upper side

Lower

side

Safety wire

2Insert

1Disconnect

3Bend

Mark 2

Mark 1

4Connect

Safety wire angle

Anchor bolt

Camera

mounting

stage

Screw (M4) × 6

5. Connect the mounting chassis to

another tip of the safety wire.

6. Insert the mounting chassis into the

hole made in Step 1.

* [For those concerned with the direction

of the brand logo]

The direction of the logo on the decora-

tive cover you installed in procedure 14 is

set according to the direction the mount-

ing chassis is inserted. (see the below

illustration)

Ceiling board fixing bracket × 4

3 lines

Use the ceiling board fixing bracket as a guide

Align the brand logo with the ceiling board fix-

ing bracket, which is nearly in the center of the

2 groups of 3 lines.

Direction of the brand logo on

the decorative cover

Safety wire (Accessory)

Mounting chassis

Insert the mounting

chassis into the hole

Roof space

7. Secure the mounting chassis to the

ceiling board with the ceiling board

fixing screws (4 positions).

Engage the top of the mounting chas-1

sis with the 1st anchor bolt.

Secure the mounting chassis by turn-2

ing the ceiling board fixing screws

clockwise.

Turning the ceiling board fixing screws

clockwise provides ceiling board tight-

ening between the bottom of the

mounting chassis and ceiling board

fixing bracket resulting in mounting

chassis securing.

(Recommended tigtening torque:

0.78 N •m {0.58 lbf •ft}

Secure the top of the mounting chas-3

sis with double nuts.

Important: When securing this bracket on

the ceiling, make sure that the four ceil-

ing board fixing brackets are open as

shown in the figure.

Prepare the cables.8.

Run the cables from the space of the mounting chassis.

Ceiling board

fixing screw

Ceiling

board fixing

bracket

Insert the anchor bolt

Nut

Double nuts

Turn clockwise

1st anchor bolt

Ceiling board

9. Attach the base unit or the camera

mounting bracket to the camera

mounting stage.

Insert and tighten the 4 screws (M4, acces-

sory)

(Recommended tightening torque:

1.57 N •m {1.16 lbf •ft})

Note:

Which component to attach depends•

on the camera model. The base unit is

a main unit component of the camera

and the camera mounting bracket is an

accessory of the camera.

The base unit is attached in figures•

shown in the following descriptions.

Important:

Make sure to attach the camera mounting bracket in correct direction. If you attempt to•

attach it in the wrong direction, some part of it will interfere with the camera mounting

stage. Do not try to forcibly attach it as it may cause a failure or falling.

Correct direction Wrong direction

Base unit

Camera mounting bracket

* Make sure to

attach it in cor-

rect direction.

10. Mount the camera mounting stage on

the mounting chassis.

Insert the camera mounting stage1

flanges (3 flanges) into the flange slots

(3 slots) in the camera mounting chas-

sis. Push it into the mounting chassis

as far as it will go.

Once it is inserted into the mounting2

chassis, rotate it clockwise until it con-

tacts the mounting chassis’s turn stop-

per.

Caution: If it is difficult to move,

grasp the flanges and legs and

rotate.

Insert and tighten the 3 screws you3

removed in Step 4. * Refer to <Fig.A>

(Recommended tightening torque:

1.57 N •m {1.16 lbf •ft})

Insert and tighten the 3 screws you4

removed in Step 4. * Refer to <Fig.B>

(Recommended tightening torque:

1.57 N •m {1.16 lbf •ft})

Important: Do not let the cables be

caught during installation work.

Flanges

Legs

Slots for the camera mounting stage flanges

* 1 position on the rear side

Turn stopper

* 2 positions

on the rear

side

<Fig. A>

<Fig. B>

Table of contents

Other Panasonic Rack & Stand manuals

Panasonic

Panasonic TY27SF24M User manual

Panasonic

Panasonic TY-ST65PE8 User manual

Panasonic

Panasonic WV-Q201 User manual

Panasonic

Panasonic WV-QWL500-W User manual

Panasonic

Panasonic TY-ST42PX5W User manual

Panasonic

Panasonic TY-ST42D2-WG User manual

Panasonic

Panasonic ET-JPC200BK User manual

Panasonic

Panasonic TY-S37PA60W User manual

Panasonic

Panasonic WV-Q150CE User manual

Panasonic

Panasonic TY-WK65PR20 User manual

Panasonic

Panasonic ET-PFD310 User manual

Panasonic

Panasonic TY-ST75PE9 User manual

Panasonic

Panasonic TY-CE42PS20 User manual

Panasonic

Panasonic TY-VK55LV1 User manual

Panasonic

Panasonic WV-Q119 User manual

Panasonic

Panasonic WV-Q160C User manual

Panasonic

Panasonic WV-Q204/1S User manual

Panasonic

Panasonic TY-S37PX600W User manual

Panasonic

Panasonic TY-S37PX60W User manual

Panasonic

Panasonic ET-PFD510 User manual

Panasonic

Panasonic TY-ST32L7-S User manual

Panasonic

Panasonic WV-Q110E User manual

Panasonic

Panasonic WV-Q174 User manual

Panasonic

Panasonic ET-JPF100BU User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 