Panasonic PTL759VU - LCD PROJECTOR User manual

ORDERNO. VED0108317C0

D10

LCD Projector

PT-L759VU/ PT-L759XU/ PT-L759VE / PT-L759XE / PT-

L1759V/ PT-L1759X

SPECIFICATIONS

Specifications

LCD panels

1.3”Polysilicon LCD panel (W/MLA)X3, / RGBshutter

method, using TranslucentTNcrystal panels

Drivemethod

ActiveMatrix4:3AspectRatio panels, TFT (Thin Film

Transistor)

No. ofpixels

786 432 (1024 X768)stripepixelsX3panels

Lens

PT-L759XU/XE/PT-L1759X:

1-1.3zoomlens, F2.0-2.5, f45 mm-59 mm Manual Focus

PT-L759VU/VE/PT-L1759V:

1-1.3zoomlens, F2.5-3.0, f45 mm-59 mm Manual Focus

Projectorlamp

220 WUHMLamp

Contrastratio

450 :1

Brightness

PT-L759XU/XE/PT-L1759X:

3100 lm(ANSI)

Note

-Specificationsand design subjectto changewithoutnotice.

PT-L759VU/VE/PT-L1759V:

2400 lm(ANSI)

No. ofcolors

16 777 216

Screen size

0.508 m(20”)-7.620 m(300”) (measured diagonally)

Projection (throw)distance

0.85 m(2.62’)-13.45 m(44.29’)

Lensaxisshift

6:1Lowposition

Compatiblescanning frequency

Video/S-Video signal

H-Frequency15.74 kHz/15.63 kHzV-Frequency50 Hz/60 Hz

RGBsignal

H-Frequency24 kHz-110 kHz(TTL Level)/ V-Frequency50 Hz-

101 Hz(TTL Level)/ Dotclock-Frequency135 MHzorlower

DVI-Dsignal:PT-L759XU/XE/PT-L1759X

VGA60 Hz, SVGA60 Hz, XGA60 Hz, SXGA60 Hz

YPBPRsignal

480 i H-Frequency

15.75 kHz V-Frequency60 Hz

480 p H-Frequency31.5kHz V-Frequency60 Hz

625 i H-Frequency

15.63 kHz V-Frequency50 Hz

720 p H-Frequency45 kHz V-Frequency60 Hz

1080 i H-Frequency

33.75 kHz V-Frequency60 Hz

Video systems

PAL/SECAM/NTSC/PAL-M/PAL-N/NTSC4.43

Connectors

RGB1/YPBPRInput:D-Sub mini 15-pin X1

RGB2 Input/RGB1 Output:D-Sub mini 15-pin X1

Video signal

RGBAnalog

0.7V[p-p], 1.0V[p-p]with syncon green, 75

YPBPR

Y: 1.0V[p-p], PBPR:0.7V[p-p], 75

Syncsignal

H/Vseparate, H/Vcomposite, orSync-on-Green

DVI-DInput:DVI-D24-pin X1:PT-L759XU/XE/PT-L1759X

Audio Input(forRGB/YPBPR/DVI-D):M3stereo mini pin X1

0.32 V[rms]

Video Input:RCApin X1

1V[p-p], syncnegative, 75 terminated

S-Video Input:Mini Din 4-pin X1

Note

-Specificationsand design subjectto changewithoutnotice.

Y(Iuminance signal):1V[p-p], syncnegative, / 75

terminated

C(chrominance signal):burst0.286 V[p-p], / 75

terminated

Audio Input(forVideo/S-Video):M3stereo mini pin X1

0.32 V[rms]

Audio output:M3stereo mini pin X1

0.32 V[rms]

USB4-pin X1(TypeB)

MOUSE Port:13-Pin round connectorX1

Serial Port(RS-232C):Mini Din 8-pin X1

Controls

CabinetButtons/ Switches

Main Power ON/OFF, Power ON/OFF, Volume+/-, Auto setup,

Menu, Input, , , , , Enter, Keystone

RemoteControl Buttons

Power ON/OFF, Freeze, Shutter, Mute, Volume+/-, Enter,

Menu, Input, , , , , Laser, D. Zoom+/-,

Keystone, Auto setup, Mouse, Click1, Click2

Audio output

1.5W(10%THD)

Speaker

70 mm X40 mm X1(2.76”X1.58”X1)

Operating Temperature

0°Cto 40°C(32°F to 104°F)

Operating Humidity

20%-80%(non-condensing)

StorageTemperature

-20°Cto 40°C(-4°F to 104°F) Humidity(5%-85%(non-

condensing))

-20°Cto 60°C(-4°F to 140°F) Humidity(Normal humidity)

Power Supply

100 V-240 VAC(50 Hzor60 Hz) Automatic

Power consumption

370 W

DimensionsWXHXD

263 mm X124 mm X336 mm (10-6/16”X4-14/16”X13-14/16”)

Amps

3.7A-1.5A

Weight

6.3Kg (13.9lbs.)

Approvals

FCC, UL, C-UL, CE, VDE, FDA, CCIB

Note

-Specificationsand design subjectto changewithoutnotice.

Unauthorizedcopying and distribution isaviolation oflaw.

Please refer to theOperating Instructionsin theappendix

folder. / (Go to Appendix List)

1. SAFETY PRECAUTIONS

1.1. GENERALGUIDELINES

1. For continuedsafety, no modification ofanycircuitshouldbe

attempted.

2. Disconnect ACPlug beforedisassembling thisunit.

3. Itisadvisabletouse anisolation transformerintheACsupply

beforeservicing.

4. Whenservicing, observetheoriginal leaddress. Ifashortcircuit

isfound, replace all parts whichhavebeenoverheatedor

damagedbytheshortcircuit.

5. Afterservicing, see toitthat all theprotectivedevices suchas

insulation barriers, insulation papers, shield, and isolation R-C

combinationsetc. areproperlyinstalled.

6. Afterservicing, besuretorestorethewires, leads, insulation

barriers, shields, etc.

7. Afterservicing, make theleakagecurrentchecks topreventthe

customerfrom being exposedtoshock hazards.

Caution:

Use aseparate Isolation Transformerfor thisunitwhenservicing.

1.2. LEAKAGE CURRENTCHECK

1. Connect ACPlug to120 voltor 240 voltACoutlet.

Donotuse theground prong ofACPlug. (See Fig. 1-2-1)

Donotuse aisolation transformerfor thischeck.

Fig. 1-2-1

2. Connect a1500 ohms, 10 watts resistor, inparallel witha0.15

Fcapacitor, betweeneachexposedmetallicparton theset and a

good earthground. (See Fig. 1-2-2)

Fig. 1-2-2

3. Use anACvoltmeter, with1000 ohms/voltor moresensitivity, to

measurethepotential across theresistor.

4. Check eachexposedmetallicpart, and measurethevoltageat

eachpoint.

5. Reverse theACplug intheACoutlet and repeat eachoftheabove

measurements.

6. Thepotential at anypointshouldnotexceed1.125 voltRMS. A

leakagecurrenttester(Simpson Model 229 equivalent) maybe

usedtomake thehotchecks, leakagecurrentmust notexceed

0.75 milliamp. Incase ameasurementisoutsideofthe

limitsspecified, thereisapossibilityofshock hazard, and theLCD

Projector shouldberepairedand recheckedbeforeitisreturned

tothecustomer.

1.3. UV-PRECAUTION

1. Besuretodisconnect theACPlug whenreplacing thelamp.

2. Since thelamp reaches averyhigh temperatureduring its

operation, waituntil ithas completelycooledoff whenreplacing

theLamp Unit.

3. Thelamp emits small amounts ofUV-Radiation.

Avoiddirect-eyecontact. Fig. 1-3-1

2. SERVICE CAUTIONS AND NOTES

2.1. SERVICE POSITION

The position shownin Fig. 2-1-1 is usedforchecking, adjusting and replacing parts.

Extension Cable (LSUA0024)is necessaryforservicing.

Fig. 2-1-1

1. Intheorderdescribedinthe"3.2. DisassemblyMethod of

Cabinet Parts"of3. Disassembly/AssemblyProcedures, remove

theTop CoverAss'y.

2. Remove7screws(F)and 2screws(G)as shownin Fig. 3-2-6.

3. Disconnect connectorsP3501, P3502, P3503 and P4001 on the

MainC.B.A.

4. Connect Extension Cables as follows:

A. Connect Extension Cable(36 pin)betweenP3501 on theMain

C.B.A. and LCD RedUnit.a) Connect Extension Cable(36 pin)

betweenP3501 on theMainC.B.A. and LCD RedUnit.

B. Connect Extension Cable(36 pin)betweenP3502 on theMain

C.B.A. and LCD GreenUnit.

C. Connect Extension Cable(36 pin)betweenP3503 on theMain

C.B.A. and LCD BlueUnit.

5. Carefullyplace theMainC.B.A. as shownin Fig. 2-1-2.

Note:

The LCD Projectorpowercannot be turnedon unless the AirFilterunitis correctlyinstalled.

6. Afterservicing, removeExtension Cables.

7. Reinstall theMainC.B.A., and reconnect connectors.

8. Make surethat all wires and leadsareplacedintheiroriginal

position.

Fig. 2-1-2

2.2. HowtodisplayLamp operation time(Service Mode)

1. Connect ajumperwirebetweenTP6012 and TP6013 on Main

C.B.A. for over5secondsas shownin Fig. 2-2-1.

Fig. 2-2-1

2. Lamp operation timewill bedisplayedas shownin Fig. 2-2-2.

Fig. 2-2-2

3. Connect ajumperwirebetweenTP6012 and TP6013 for over5

secondsagainor press MENU button on remote control inorder

torelease from service mode.

Note:

Afterreplacing MainC.B.A., memorydata suchas

historyof lamp operation time has been

reset.However, itcanbe remainedbyinstalling

EEPROMIC (IC6009)to replacedMainC.B.A. from

original MainC.B.A.

2.3. HowtoinitializeEEPROMIC

WhenEEPROMIC’s (IC6009, IC6010)on MainC.B.A. is replaced:

Afterreplacing EEPROMIC’s (IC6009, IC6010), be sure to performeachof following steps inthe

orderpresented.

1. Connect ajumperwirebetweenTP6016 and TP6017 on Main

C.B.A. for over5secondsas shownin Fig. 2-2-1 toenterFactory

mode.

2. “FACTORY”appearson screen(Factorymode).

3. Connect ajumperwirebetweenTP6016 and TP6017 againfor

over5secondstoinitializeEEPROMIC’s.

4. “SelfCheck”appearson screenwheninitializing starts.

5. RemovethejumperwirebetweenTP6016 and TP6017. /

“MEMORY OK”appearson screenwheninitializing iscomplete. /

Afterinitializing iscomplete, perform necessaryadjustments,

referring tostep6through 12.

6. Press thePOWERbutton on remote control once.

7. While"Please press POWERbutton againtopoweroff."is

displayed, press theMENU button on remote control.

8. TheFactoryAdjust Modeappearson screen.

9. Perform adjustments 4.4.1through 4.4.5and 4.4.12 through 4.4.17.

10. Aftercompleting all adjustments, press theMENU button to

release from theFactoryAdjust Mode.

11. Press thePOWERbutton on remote control once.

12. While"Please press POWERbutton againtopoweroff."is

displayed, press the POWER button on remote control topower

off. Then, all adjustmentdata ismemorizedinEEPROMIC’s.

Note:

1. Wheninitializing EEPROMIC’s, memorydata suchas historyof

lamp operation timeand adjustmentdata will bereset.

2. When“MEMORY NG”appearsinstep5, repeat step3through

step5until “MEMORY OK”appears.

2.4. Lamp replacementprocedure

Caution:

Lamp replacementprocedureCaution:Because ofpossibilityof

injury, strictlyfollowthereplacementprocedurebelow.

1. Afterthecooling fanhas stopped, and STANDBY(R) ON(G)

indicator turnssolidred. Set theMainPowerSwitchtoOFF and

unplug thepowercord.

Note:

Please waitmore thanone hourforlamp replacement.

[Ifyou needtoreplace thelamp moreurgently]

-TheLCD Projector has aforcedcooling feature. Afterthe

POWERswitchisturnedOFF, and sometimeduring aboutthe

first minute ofthenormal cooling fanoperation, press and

Other manuals for PTL759VU - LCD PROJECTOR

This manual suits for next models

Table of contents

Other Panasonic Projector manuals

Panasonic

Panasonic PT-D5700U - XGA DLP Projector User manual

Panasonic

Panasonic PT-51D31CE User manual

Panasonic

Panasonic PT-L759V System manual

Panasonic

Panasonic PT-VW530 User manual

Panasonic

Panasonic PT-D10000 Series User manual

Panasonic

Panasonic PTLC50U - LCD PROJECTOR User manual

Panasonic

Panasonic WE160 - VIDEO IMAGER User manual

Panasonic

Panasonic PT-AR100EH Operating instructions

Panasonic

Panasonic PT-L735: PT-L735NT User manual

Panasonic

Panasonic PT-FZ570U Operating instructions

Panasonic

Panasonic PTST10E - LCD PROJECTOR User manual

Panasonic

Panasonic PT-DW5100EL User manual

Panasonic

Panasonic PTL501U - LCD PROJECTOR User manual

Panasonic

Panasonic PT-RZ470UK User manual

Panasonic

Panasonic PT-RQ35KU User manual

Panasonic

Panasonic PT-AE900U User manual

Panasonic

Panasonic PT-L6510E User manual

Panasonic

Panasonic PT-LB50 System manual

Panasonic

Panasonic PT-AE3000E User manual

Panasonic

Panasonic PTL711U - LCD PROJECTOR User manual

Panasonic

Panasonic PT-AE1000U - LCD Projector - HD 1080p User manual

Panasonic

Panasonic PTL785U - LCD PROJECTOR UNIT User manual

Panasonic

Panasonic PT-LB80NT System manual

Panasonic

Panasonic PT-CMZ50 User manual

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

InFocus

InFocus LitePro 560 user guide

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual

Asus

Asus ZenBeam Latte user manual