Panasonic DVD-S42EE User manual

ORDERNO.CHM0603009CE

DVDPlayer

DVD-S42EE / DVD-S42GC / DVD-S42GCA / DVD-S42GCS /

DVD-S42GCU / DVD-S42PL / DVD-S42PLA

DL4.1Mechanism Series

Color

(S).......................Silver Type

SPECIFICATIONS

Specifications

Power supply: AC230 V, 50 Hz

(DVD-S42EE)

AC110-240 V, 50/60 Hz

(DVD-S42GC/GCA/GCU/GCS/

PL)

AC120 V, 60 Hz

(DVD-S42PLA)

Power consumption: 11 W

Power consumption instandbymode:

1W(approx.)

Dimensions: 430 (W) × 251 (D) × 43 (H) mm

Mass: 2.2kg(approx.)

Signal system: PAL625/50, PAL525/60, NTSC

(DVD-S42EE/GC/GCA/GCS/

GCU)

NTSC

(DVD-S42PLA/PL)

Operating temperature range: + 5to+ 35 °C

Operating humidityrange: 5to90 %RH (no

condensation)

Discs played[8cm (3") or12 cm (5")]:

(1) DVD (DVD-Video, DivX*6,7)

(2) DVD-RAM (DVD-VR, JPEG*4,7, MPEG4*5,7, DivX*6,7,

MP3*2,7)

(3) DVD-R (DVD-Video, DVD-VR, JPEG*4,7, MP3*2,7, DivX*

6,7, MPEG4*5,7)

(4) DVD-R DL(DVD-Video, DVD-VR)

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

(5) DVD-RW(DVD-Video, DVD-VR, JPEG*4,7, MP3*2,7, DivX*

6,7, MPEG4*5,7)

(6) +R/+RW(Video)

(7) +R DL(Video)

(8) CD, CD-R / CD-RW(CD-DA, VideoCD, SVCD*1, MP3*2,7,

WMA*3,7, JPEG*4,7 , MPEG4*5,7, DivX*6,7,

HighMATLevel 2(Audioand Image))

*1 Conforming toIEC62107

*2 MPEG-1Layer 3, MPEG-2Layer 3

*3 WindowsMediaAudioVer.9.0L3

Not compatiblewithMultipleBit Rate(MBR)

*4 Exif Ver2.1JPEG Baselinefiles

Picture resolution: between160 × 120 and 6144 × 4096

pixels(Sub sampling is4:0:0, 4:2:2, 4:2:0, 4:4:4)

Extremelylong and slender pictures maynot be

displayed.

*5 MPEG4datarecordedwiththePanasonicSD multi

cameras orDVD videorecorders conforming toSD

VIDEO specifications(ASFstandard) /MPEG4(Simple

Profile) videosystem/G.726 audiosystem

*6 Playsall versionsof DivX video(including DivX 6)

with

standardplayback of DivX mediafiles. Certifiedto

theDivX

Home Theater Profile.

GMC (Global Motion Compensation) not supported.

*7 Thetotal combinedmaximumnumber of recognizable

audio, picture and videocontentsand groups: 4000

audio, picture and videocontentsand 400 groups.

Videooutput:

Output level: 1Vp-p(75 )

Output terminal: Pinjack (1system)/AV

(DVD-S42EE)

Pinjack (1system)

(DVD-S42GC/GCA/GCS/GCU/

PLA/PL)

S videooutput:

Y output level: 1Vp-p(75 )

C output level: NTSC: 0.286 Vp-p(75 )

PAL: 0.300 Vp-p(75 )

(DVD-S42EE/GC/GCA/GCS/

GCU)

NTSC: 0.286 Vp-p(75 )

(DVD-S42PL/PLA)

Output terminal: AV

(DVD-S42EE)

S terminal (1system)

(DVD-S42GC/GCA/GCS/GCU/

PLA/PL)

Component videooutput:

[NTSC: (480)p/(480)i,

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

PAL: (576)p/(576)i]

(DVD-S42EE/GC/GCA/GCS/GCU)

[NTSC: (480)p/(480)i]

(DVD-S42PL/PLA)

Y output level: 1Vp-p(75 )

P B output level: 0.7Vp-p(75 )

P R output level: 0.7Vp-p(75 )

Output terminal: Pinjack (Y: green, P B : blue,

P R : red)

Number of terminals: 1system

RGB videooutput: (DVD-S42EE)

R output level: 0.7Vp-p(75 )

G output level: 0.7Vp-p(75 )

B output level: 0.7Vp-p(75 )

Output terminal: AV

Videoperformance:

Horizontal resolution: More than500 lines

VideoS/N ratio: More than65dB

Audiooutput:

Output level: 2Vrms (1kHz, 0dB)

Output terminal: Pinjack/AV

(DVD-S42EE)

Pinjack

(DVD-S42GC/GCA/GCS/GCU/

PL/PLA)

Number of terminals:

2channel: 1system

Audioperformance:

(1) Frequencyresponse:

DVD (linear audio): 4Hz-22 kHz (48 kHz sampling)

4Hz-44 kHz (96 kHz sampling)

CD audio: 4Hz-20 kHz

(2) S / N ratio:

CD audio: 115 dB

(3) Dynamicrange:

DVD (linear audio): 102 dB

CD audio: 98 dB

(4) Total harmonic

distortion:

CD audio: 0.003 %

Digital audiooutput:

Coaxial digital output: Pinjack

Pickup

Wavelength: 662 nm/ 785 nm

Laser power: CLASS 2/ CLASS 3A

Note:

Specificationsare subject tochangewithout notice.

Mass and dimensionsare approximate.

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Solder:

Thismodel uses leadfree solder (PbF).

Unauthorized copying and distribution isaviolation of law.

1. IMPORTANT SERVICE INFORMATION

1.1. Notes

Whenyou replace EEPROM orexchange MODULE P.C.B., you have totake "Manual for

customer" tothe customerwithunit.

(alsointhe case of unit exchange)

Please take and use "Manual forcustomer" frombelow.

1. Come with MODULE P.C.B. or EEPROM(Service part).

2. Make aphotocopysection 1.3. "Manual for customer" on this

service manual.

“Manual forcustomer” has important information for"DivX Video-on-Demand Service" user.

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Please don't forget take it tothe customerwithunit!

1.2. About DivX

1.2.1. DivX

A videocompression format developedbyDivXNetworks, Inc. that compresses videofiles

without anyconsiderable loss of videoquality.

1.2.2. About DivX Video-on-Demand Content

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

1.3. Manual for Customer

2. SAFETY PRECAUTIONS

2.1. GENERALGUIDELINES

1. When servicing, observe the original lead dress. Ifashort circuit

isfound, replace all parts which have been overheated or

damaged bythe short circuit.

2. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

2.1.1. LEAKAGE CURRENTCOLD CHECK

1. Unplug the AC cord and connect ajumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metalliccabinet part on the

equipment such as screwheads, connectors, control shafts, etc.

When the exposed metallicpart has areturn path to thechassis,

the reading shouldbe between 1M and 5.2M . / When the

exposed metal does not have areturn path to the chassis, the

reading must be . Figure 1

2.1.2. LEAKAGE CURRENTHOTCHECK (See Figure 1 .)

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

1. Plug the AC cord directlyinto the AC outlet. Donot use an

isolation transformer for thischeck.

2. Connect a1.5k , 10 watts resistor, inparallel with a0.15 F

capacitors, between each exposed metallicpart on the set and a

good earth ground such as awater pipe, as shownin Figure 1.

3. Use an AC voltmeter, with 1000 ohms/voltor more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reverse the AC plug inthe AC outlet and repeat each of the above

measurements.

6. The potential at anypoint shouldnot exceed 0.75 volts RMS. A

leakage current tester (Simpson Model 229 or equivalent) maybe

used to make the hot checks, leakage current must not exceed 1/2

milliamp. Incase ameasurement isoutside of the limits specified,

there isapossibilityof ashock hazard, and the equipment should

be repaired and rechecked before itisreturned to the customer.

3. PREVENTION OF ELECTRO STATIC DISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistorsand semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodybytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap, which

shouldbe removed for potential shock reasons prior to applying

power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as alminum foil,

to prevent electrostaticcharge buildup or exposure of the

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan anti-staticsolder removal device. Some solder

removal devices not classified as "anti-static(ESDprotected)"

can generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, alminum foil or

comparableconductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

Caution

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient

todamage an ES device).

4. PRECAUTION OF LASER DIODE

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

5. SERVICE CAUTION BASED ON LEGAL

RESTRICTIONS

5.1. General description about Lead Free Solder (PbF)

The leadfree solderhas beenusedinthe mounting process of all electrical components on the

printedcircuit boards usedforthis equipment inconsidering the globallyenvironmental

conservation.

The normal solderis the alloyof tin(Sn) and lead(Pb). Onthe otherhand, the leadfree solderis

the alloymainlyconsists of tin(Sn), silver(Ag) and Copper(Cu), and the melting point of the

leadfree solderis higherapprox.30°C (86°F) more thanthat of the normal solder.

Definition of PCB LeadFree Solderbeing used

Service caution forrepairwork using LeadFree Solder(PbF)

-The lead free solder has to be used when repairing the equipment

PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

Other manuals for DVD-S42EE

This manual suits for next models

Table of contents

Other Panasonic DVD Player manuals

Panasonic

Panasonic DVD-S68GA User manual

Panasonic

Panasonic DVDRA60 - DIG. VIDEO DISCPLAYE User manual

Panasonic

Panasonic DVD-LS91PP User manual

Panasonic

Panasonic DVD-K510 User manual

Panasonic

Panasonic DVDLV57 - PORTABLE DVD User manual

Panasonic

Panasonic SC-VK880 User manual

Panasonic

Panasonic DVD-LS80P User manual

Panasonic

Panasonic DVD-S55 User manual

Panasonic

Panasonic DIGA DMR-ES15 User manual

Panasonic

Panasonic DVD-S97EE User manual

Panasonic

Panasonic DVD-F65 User manual

Panasonic

Panasonic DVD-S32EB User manual

Panasonic

Panasonic DVD-X410 User manual

Panasonic

Panasonic DVD-S55S Operating User manual

Panasonic

Panasonic DVD-S97 User manual

Panasonic

Panasonic DMP-BDT700 Technical specifications

Panasonic

Panasonic Diga DMR-EZ47 Use and care manual

Panasonic

Panasonic PVD4735S - DVD/VCR DECK User manual

Panasonic

Panasonic DVDH2000 - DIG. VIDEO DISCPLAYE User manual

Panasonic

Panasonic DVDA310 - DIG. VIDEO DISCPLAYE User manual

Panasonic

Panasonic CXDVP292U - CAR DVD PLAYER User manual

Panasonic

Panasonic DVDPA65 - PORTABLE DVD User manual

Panasonic

Panasonic DVD-XV10E User manual

Panasonic

Panasonic DVD-S500 User manual

Popular DVD Player manuals by other brands

Sony

Sony DVP-F11 Service manual

Philips

Philips DVP3560K/F8 user manual

LENCO

LENCO DVP-740 X2 user manual

JVC

JVC XV-N650BEU Service manual

Aiwa

Aiwa XD-DV370 operating instructions

MedeaWiz

MedeaWiz Sprite 4K DV-S4 user manual

Denon

Denon DVM-1805 - DVD Changer operating instructions

Toshiba

Toshiba SD-3815 owner's manual

Tevion

Tevion 44330 user guide

Samsung

Samsung DVD-HD860 manual

Sylvania

Sylvania DP170SL8 Service manual

Toshiba

Toshiba SD-P1200 Service manual

JVC

JVC XV-D9000E instructions

Dolby Laboratories

Dolby Laboratories CP650 user manual

Philips

Philips DVD737K/931 Technical specifications

Denon

Denon DVD-5900 Service manual

Philips

Philips DVD 951 Specifications

Philips

Philips DVDR3460 quick start guide