Panasonic OneHome BB-HCM581A Quick start guide

HomeLogic LLC ●

100 Hoods Lane

●

Marblehead, MA 09145

●

Phone (781) 639-5155

●

Fax (781) 639-9677

OneHome™

Management and Control Solutions

Camera Integration Note

Manufacturer: Panasonic

Model Number(s): BB-HCM580A/581A

Comments: OneHome version 4.0.1310 or newer, Network Camera (version 3.10)

Document Revision Date: 5/19/2011

NOTE: This document refers to Camera setup in software versions below 5.2 ONLY.

Please see the Rev 5.2 Integration Note for systems running 5.2 or greater.

VERVIEW AND SUPPORTED FEATURES

BB-HCM580/581A’

S SUPPORT THE FOLLOWING FEATURES

Pan / Tilt / Zoom: The camera can be turned to see various locations and zoom in and out.

Presets: These cameras support presets, allowing the user to store predefined locations such as a

driveway or pool. This feature requires OneHome software version 4.0 or later.

Motion Detection: These cameras support motion detection to trigger events in the OneHome system.

Video Out: The camera includes an analog video output, which can be connected to an analog DVR to

provide separate recording, or to a TV modulator to enable camera viewing on a television.

Image Flip: The camera can be mounted with its base up or down, and the image will appear normal.

HESE

AMERAS

NOT

SUPPORT THE FOLLOWING FEATURES

Input/Output: These cameras include an I/O connector for sensor inputs and alarm outputs. These are

not supported by the OneHome system at this time.

2 of 10

NSTALLATION

VERVIEW

Installing the Panasonic camera can be broken down into the following steps:

1. Install cameras at desired locations, and pull power and Cat5 cabling as needed. Refer to the

Panasonic documentation for mounting details.

2. Connect the cameras electrically to the home network and configure the cameras. See Camera

Configuration.

3. Integrate the cameras into the OneHome system and test proper operation. This step is outlined

in HomeLogic Configuration Details.

AMERA

ONFIGURATION

The camera configuration is done with software provided by Panasonic, which must be run from a

computer with Windows also connected to the same network as the camera.

The software program from Panasonic is EasyConfig.exe: the version we checked is shown at the top.

MPORTANT

OTES

1. Cameras must be configured one at a time: If you are installing more than one camera, setup

the first one completely before powering up subsequent cameras.

2. Setup the camera within 20 minutes: Initial settings must be made within 20 minutes of the

camera being turned on. If the camera has been powered up for more than 20 minutes, cycle

power to the camera before proceeding.

3. DON’T LOSE THE CAMERA PASSWORD: During setup you will create a user name and

password, which are required to make any other changes in the future. If you lose the user name

or password you will have to factory reset the camera and repeat this entire procedure.

4. DEFAULT USER NAME / PASSWORD: For Panasonic cameras, our default user name is

Administrator and our default password is password.

TARTING THE

ANASONIC

AMERA

OFTWARE

1. Insert the CD from the camera into your PC: It should autostart the Network Camera Setup

software. If it does not, launch Setup.exe from the Panasonic CD.

2. The following Screen appears. Choose Search for Cameras.

3 of 10

3. Wait a moment to allow the software to find the camera: the following screen appears.

4. Select the desired camera, and then click the Access Camera button. After a short delay you will

see a new browser window with the initial password screen below:

5. Type in your desired user name and password and click Save. By default we set the user name to

Administrator and the password to password.

6. After a moment initial setup will complete. When prompted with the screen below, click the “To

Single Camera page” button.

4 of 10

7. You will be prompted to enter your user name and password to login, as shown in the image

below. Type in the user name and password you just set, and click OK.

AMERA

ETTINGS

1. After typing in your user name and password, you will be shown the standard browser interface to

the camera.

2. The system may attempt to install an ActiveX control to show the camera image in the browser

window. This control is not needed for proper OneHome operation, but is needed if you wish to

see the camera image on that computer. If any dialogs appear, close them or accept the ActiveX

control as appropriate for your situation.

3. Click Setup at the top to bring up the screen shown below:

5 of 10

4. Click UPnP on the left, then click Disable in the both parts of the screen, as shown below. Click

Save to store your settings.

5. Under Accounts to the left, click Administrator to bring up the screen below. Click Permit

access from guest users, as shown below. Leave the Password boxes blank to prevent

changing your password, then click Save to store your changes. Click OK on any warning

messages.

6 of 10

6. Click on General User under Accounts. Click on Guest User and the click the Modify button.

7. Set Video Display time to Unlimited, and then click the Level 3 button to automatically check all

boxes on the page. Save when finished.

7 of 10

8. Click Network (IPv4) to bring up the network settings screen shown below.

8 of 10

9. Click Static in the Connection Mode to bring up the screen below.

10. Set the IP address to the desired value: we suggest setting the first camera to 192.168.0.80, the

second to 192.168.0.81, and so forth. Set the Default Gateway and the 1

DNS server to the

router IP Address, and then click Save to save the settings.

11. If prompted, click to Restart to restart the camera. Note that the camera is now at a different IP

address, so the browser window won’t show the camera.

12. Go to the address line in the browser, and put in the new IP address as shown below:

9 of 10

13. This brings up the camera’s home page similar to shown below:

14. The camera is now at the correct IP address with the correct settings.

OTION

ETECTION FOR

OME

OGIC

DVR

ONFIGURATION

To use Panasonic IP Cameras with the HomeLogic DVR tab, enter the web configuration by typing the

camera IP into the browser and logging on using your username and password. Click Setup, and then

below Buffer/Transfer click Motion Detection. Threshold is the measure of the camera’s sensitivity to

change—a lower setting will cause it pick up smaller changes. Sensitivity affects the light sensitivity—a

higher setting will result in more frequent detections of lighting changes.

Typically, the Threshold should be set to the LOWEST setting and Sensitivity should be set to the

HIGHEST.

Please see the DVR Integration Note for full details on setting up the DVR tab in HomeLogic

10 of 10

OME

OGIC

ONFIGURATION

ETAILS

The following table provides settings used in the HomeLogic Configurator. Please refer to the Configurator Reference Guide for more details.

In the table below:

o“<User Defined>”, etc. Type in the desired name for the item.

Devices Variable Name Setting Comments

Communication Device N/A (See Note 1) N/A (See Note 1)

Video Cameras Name <User Defined>

Device Type Panasonic KX-HCM280A

Location <User Defined> (Not Required)

IP Address <User Defined> (Default: 192.168.0.80) (See Note 2)

Port 80 Typically left at 80

UserName <User Defined> (Default: Administrator)

Password <User Defined> (Default: password)

Low-Res Panning <Select> (Default: <No>)

Flip Image 180 <Select> (Default: <No>) Set to YES if camera is inverted

Hide Resolution Control <Select> (Default: <No>)

Hide Full Screen Control <Select> (Default: <No>)

Default Resolution <Select> (Default: <Auto>)

Goto Preset when Idle <Select> (Default: <NONE>) Camera will Pan/Tilt/Zoom as applicable to a certain preset when no streams active.

Record Resolution <Select> (Default: <Don't Change>) Don't Change will default to last active resolution, or set a specific resolution for recording

Record Tolerance <Select> (Default: 0% (Keep All Frames))Higher will discard frames with no motion to conserve disk space

Motion Detect <Select> (Default: Disabled)Enable to trigger event maps when motion detected (DVR)

Software Motion Trigger <Select> (Default: 50%)Lower is more sensitive.

Notes:

1. No Communication Device is needed: just add Video Cameras.

2. By default, set the first camera to 192.168.0.80, the second to 192.168.0.81, and so on.

This manual suits for next models

Table of contents

Other Panasonic Digital Camera manuals

Panasonic

Panasonic Lumix DMC-TZ25EB User manual

Panasonic

Panasonic Lumix DMC-FZ30GN User manual

Panasonic

Panasonic Lumix DMC-ZS19 User manual

Panasonic

Panasonic DMC-SZ1A User manual

Panasonic

Panasonic Lumix DC-GF10 Owner's manual

Panasonic

Panasonic Lumix DMC-TZ27EB User manual

Panasonic

Panasonic Lumix DMC-FT20EB User manual

Panasonic

Panasonic DMC-FP3AB Technical specifications

Panasonic

Panasonic Lumix DMC-ZS9 User manual

Panasonic

Panasonic LUMIX DMC-LX2PP User manual

Panasonic

Panasonic Lumix FZ20 User manual

Panasonic

Panasonic LUMIX DC-GH5M2GA User manual

Panasonic

Panasonic LUMIX DMC-FX500 User manual

Panasonic

Panasonic DC-FZ1000M2P User manual

Panasonic

Panasonic Lumix DMC-FZ35 Technical specifications

Panasonic

Panasonic LUMIX DMC-LF1 User manual

Panasonic

Panasonic Lumix DMC-LZ4PP User manual

Panasonic

Panasonic Lumix DMC-FX7 User manual

Panasonic

Panasonic Lumix DMC-LX7 Instruction Manual

Panasonic

Panasonic DMC-G85 Owner's manual

Panasonic

Panasonic Lumix DMC-FS20 User manual

Panasonic

Panasonic Lumix DMC-LZ20 Installation and service instructions

Panasonic

Panasonic Lumix DMC-GX7C Installation and service instructions

Panasonic

Panasonic Lumix DMC-FX78 User manual

Popular Digital Camera manuals by other brands

Mercury

Mercury 350K user manual

Pentax

Pentax Optio LS 465 operating manual

Sanyo

Sanyo VPC-S1085 instruction manual

GE SMART A1255 user manual

Point Grey

Point Grey Gazelle Getting started

Nikon

Nikon COOLPIX A Reference manual

Pentax

Pentax P-5 manual

BlazeVideo

BlazeVideo A280 instruction manual

Sony

Sony MCA-20 manual

Sony

Sony Alpha DSLR-A290 instruction manual

ATIK Cameras

ATIK Cameras One user manual

CohuHD Costar

CohuHD Costar 3930 Series Installation and operation manual

Leica

Leica M10-R quick start guide

FujiFilm

FujiFilm FinePix A700 owner's manual

Lorex

Lorex LNZ81P25 Series quick start guide

GE J1470S user manual

Sony

Sony A6700 Startup guide

Canon

Canon EOS ELAN7 instructions