Panasonic ZU-1870MA6T2 User manual

Spec.No.: MES-DG60B038A

SPECIFICATIONS

FOR

MANUAL INSERTION

MAGNETIC CARD READER

Z U – 1 8 7 0 M A 6 T 2

MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.

MATSUSHITA INDUSTRIAL EQUIPMENT CO.,LTD.

CONTENTS

1. INTRODUCTION---------------------------------------------------------------- P-1

2. COMPOSITION------------------------------------------------------------------ P-1

3. SPECIFICATION----------------------------------------------------------------- P-1

4. TERMINAL NO. OF CONNECTOR--------------------------------------- P-3

5. INTERFACE REQUIREMENTS--------------------------------------------- P-3

6. NOTES FOR BETTER OPERATION------------------------------------- P-5

7. APPEARANCE--------------------------------------------------------------------P-6

8. CONNECTOR DIMENSION---------------------------------------------------P-7

9. MAGNETIC CARD SPECIFICATION--------------------------------------P-7

10. LIFE OF PARTS----------------------------------------------------------------P-8

11. MAINTENANCE METHOD---------------------------------------------------P-8

12. CAUTIONS ON THE USE---------------------------------------------------P-8

1. INTRODUCTION

This specification applies to the Panasonic magnetic card reader,

featuring small size, light weight and high performance.

2. COMPOSITION

The magnetic card reader is composed of the mechanical portion,

double circuits for reading.

1) Mechanical portion

The mechanical portion is mainly composed of the following parts.

1. Body (Color:Transparence)

2. Card entrance slot (Color: Black)

3. Magnetic head

4. Rubber seal

2) Circuit portion

1. Read amplifier circuit for 2 tracks

3. SPECIFICATION

3.1 CARD STANDARD

Refer to Magnetic Card Specification (9).

3.2 FUNCTION

(1) Read/Write : Read only

(2) Read timing : Ejection

(3) Compatibility : Cards and installation

(4) Installation of the transport : Horizontal direction

3.3 BASIC PERFORMANCE

(1) Performance

(2) Card operation speed : 10 cm/s to 100 cm/s

(3) Magnetic head Channel : 2

Channel width : 1.4 mm

(4) Insulation resistance : More than 10 MΩat DC 250 V

(Measured between P.C.B. ground terminal and frame)

(5) UL File No. : E140407

(6) Waterproof level : IPX4

3.4 ENVIRONMENT REQUIREMENTS

(1) Temperature range : -20 oC to 60 oC

(Operation)

(2) Temperature range : -30 oC to 70 oC

(Conservation)

(3) Humidity range : 10 % RH to 90 % RH

(Operation) (No condensation allowed)

(4) Humidity range : 10 % RH to 90 % RH

(Conservation) (No condensation allowed)

(5) Vibration : Vibration sweep 10 Hz to 50 Hz,

sweep 0.5 oct/min

X,Y,Z directions : 10 m/s

(6) Shock durability : 294 m/s2 (30 G)

ZU-1870MA6T2

ISO 7810,7811

Card standard

IS01 IS02

Track used Track 1st Track 2nd

Recording method FM FM

Recording

density 210 BPI 75 BPI

Recording

Capacity

79 characters

(7-bit code)

40 characters

(5-bit code)

3.5 PHYSICAL CHARACTERISTICS

(1) Dimension : (W) 90 mm x (D) 119.5 mm x (H) 46 mm

(2) Mass : Approx. 100 g

(3) Power supply : DC 5 V ± 0.5 V / Ripple(Less than 25 mA)

(4) Ripple : Within 50 mV

p-p

(5) Operating place : Indoor

3.6 ERROR RATE

(at indoor conditions by continuous running)

(1) Error : Less than 0.5 %

* Condition ··················In a clean office room.

In damp or dusty atmosphere, the life may be 1/3 to 1/5 of

the above figure.

4. TERMINAL NO. OF CONNECTOR

4.1 OUTPUT SIGNAL

Connector: 641216-7

5. INTERFACE REQUIREMENTS

5.1 OUTPUT VOLTAGE

Min(V) Max(V) Conditions

H level "0"

4.0 V

cc I

OH= -1.0 mA

L level "1"

- 0.4 I

OL= 4.0 mA

Connector

Pin No.

Signal

name

Connector

Pin No.

Signal

name

DC 5 V 5 /RCL2

/RDT1 6 /CLD

/RCL1 7 GND

/RDT2 - -

5.2 OUTPUT SIGNALS

The following paragraphs describe the requirements

and interface signals between the user terminal and

the Magnetic Card Reader shown in Figure 1.

The general timing sequence for entering data from

the Magnetic Card Reader to the user terminal is shown

in Figure 2.

/CLD

Magnetic /RCL1,2 User's

Card Reader /RDT1,2 Terminal

GND

DC 5V

Figure 1

(1) /CLD (CARD LOAD)

The /CLD line will be High when a Magnetic Card is inserted

in the end of Magnetic Card Reader.

The /CLD line will be Low at all other times.

(2) / RCL1,2 (READ CLOCK)

This is used to sample the data line by it's falling edges.

The time relationship of the clock with respect to the other

signals is shown in Figure 2.

User's Terminal starts to carry out sampling of the read data

by the falling edge of the signal.

In case of performing sampling other than the falling edge

sampling method

(such as detecting “L” of /RCL by means of polling)to read

/RDT, check /RCL width if it is appropriate.

(3) /RDT1,2 (READ DATA)

At the moment /RCL change from High to Low ;

/RDT is "1" when the /RDT line is Low, and

/RDT is "0" when the /RDT line is High.

5.3 TIMING CHART

Detail Chart

When the jitter of the magnetic head output is 0 % , the following

equation is satisfied.

T=T1=T2=T3, t1=t2

2.54 cm/inch 1

Note : T (s) = x

Recording density (BPI) Card speed (cm/s)

6. NOTES FOR BETTER OPERATION

(1) The card should be inserted in the specified direction.

(2) The card which conformed ISO standard should be used.

(3) The cards should not be dirty, scratched or deformed.

7. APPEARANCE

8. CONNECTOR DIMENSION

POST(641216-7 AMP)

9. MAGNETIC CARD SPECIFICATION

9.1 CARD SPECIFICATION

(1) Thickness : 0.76 mm (tolerance ± 0.08 mm)

(2) Transformation : 2 mm max.

(3) Impermeability rate : More than 2.0

(Measured by light permeance desitometer)

9.2 MAGNETIC CHARACTERISTICS

(1) Coercive force (Hc) : 2.4 x 10

4A/m (300 Öe ± 12%)

(2) Residual flux (¢r) : 1.25 x 10-8 Weber/cm

(1.25 ± 0.15 maxwell/cm)

(3) Squareness ratio (¢r/¢m) : More than 0.70

10. LIFE OF PARTS

Magnetic head : 500,000 passes

*Condition ·············· In a clean office room.

In damp or dusty atmosphere, the life may be

1/3 to 1/5 of the above figure.

11. MAINTENANCE METHOD

When replacing parts, exchange the card reader unit.

12. CAUTIONS ON THE USE

Please be noted that we do not guarantee proper performance of the

card reader if it is used other than the indicated specification range.

12.1 At the installation

(1) Do not drop or bump anything against a card reader.

Otherwise, failure may be the result.

(2) Do not touch the P.C.B. with bear hands.

(3) Be sure to install on a flat surface so as to prevent any force to be

applied to the card reader at the installation.

(4) Installation of a card guide plate at the both (front and back) sides of

the card running part may reinforce stability.

(5) The card reader should avoid installation of the following environment.

· Watery, humid or dusty place.

· Near machines which generate magnetic field or inducted noise.

(printer,LED display, CRT etc.)

· Place which gets direct sunlight.

Table of contents

Panasonic ZU-1870MA6T2 User manual

Popular Card Reader manuals by other brands