Panasonic SE-HD560E User manual
ORDERNo.AD0203061C2
Amplifier
SE-HD560E / SE-HD560EB / SE-HD560EG / SE-HD560EP
Colour
(N)...........GoldType
System
SC-HD560:
Tuner; ST-HD560, Amplifier; SE-HD560,
CD Player; SL-HD560, Cassette Deck; RS-HD560,
Speakers; SB-HD560 (Made inSpain.)
SPECIFICATIONS
Specifications
1
Amplifier section (Low
frequency)
Power output:
DIN 1kHz, THD 1%
bothchannelsdriven; 2x23W(6 )
RMS 1kHz, THD 10 %
bothchannelsdriven; 2x30W(6 )
Total hormonicdistortion:
Half power at 1kHz; 0.07 %(6 )
Loadimpedance: 6
Amplifier section (High
frequency)
Power output:
DIN 10 kHz, THD 1%, / both
channelsdriven;
2x7 W(6 )
RMS 10 kHz, THD 10%, / both
channelsdriven;
2x10 W(6 )
Loadimpedance: 6
S/N:
(E), (EG), (EP) areas; 83dB
(EB) area; 78dB
Headphones
Jack type: 3.5mm STEREO
Loadimpedance: 16 - 32
General
Power supply:
(E), (EG), (EP) areas; AC 230 V, 50 Hz
(EB) area; AC 230 - 240 V, 50 Hz
Power consumption: 130 W
STANDBY condition: 0.9W
Dimensions(WxHxD): 210x104.8x309 mm
Mass: 3.4kg
Notes:
Specificationsare subject tochangewithout notice.
Mass and dimensionsare approximate.
Total harmonicdistortion ismeasuredbythedigital
spectrumanalyzer.
2002 Matsushita ElectricIndustrial Co., Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
1. Note
2
Because of unique interconnecting cables, whena component requires service, send orbring in
the entire system.
2. Before Repair
1. Turn off the power supply. Using a10 , 10 Wresistor, connect
both ends of power supplycapacitors (C601, C602) inorder to
discharge the voltage.
2. Before turning the power supplyon, after completion of repair,
slowlyapplythe primaryvoltage byusing apower supplyvoltage
controller to make sure that the consumed current at 50 HzinNO
SIGNALmode shouldbe shownbelow with respecttosupply
voltage 230/240 V.
Powersupply
voltage AC 230 V AC 240 V
Consumedcurrent
50 Hz 50 - 180 mA
3. Protection Circuitry
The protection circuitrymayhave operatedif eitherof the following conditions is noticed:
-Nosound isheard when the power issupplied.
-Sound stops during aperformance.
The functions of this circuitryis toprevent circuitrydamage if, forexample, the positive and
negative speakerconnection wires are shorted, orif speakersystems withanimpedance less
thanthe indicatedratedimpedance of this unit are used.
If this occurs, followthe procedure outlinedbellow:
1. Press the Standby/on button, switch to standbymode.
2. Determine the cause of the problem and correct it.
3. Press the Standby/on button once again, supplythe power.
Note:
When the protection circuitryfunctions, the unitwill not operate
unless the Standby/on button isfirst switched Standbyand then
ONagain.
4. Accessories
-AC power supplycord for (E), (EG), (EP) areas
(RJA0019-2X)...........................................1pc.
3
-AC power supplycord for (EB)area
(RJA0053-3X)...........................................1pc.
-AMloop antenna set
(RSA0033B-1)..............................................1pc.
-FM indoor antenna
(RSA0007).................................................1pc.
-Speaker cords
(REE1195).........................2pcs.
4
-Remote control transmitter
(EUR7702010).........................................1pc.
-Remote control batteries
(R6/LR6, AA, UM-3)..................................2pcs.
Note: These are availableon sales route.
-Antenna plug adaptor for (EB)area
(SJP9009)..............................................1pc.
5. Caution for AC Mains Lead
5
6. Location of Controls
7. Operation Checks and Component Replacement
Procedures
-Thissection describes procedures for checking the operation of
the major printed circuitboards and replacing the main
components.
-For reassemblyafter operation checks or replacement, reverse the
respective procedures. Special reassemblyprocedures are
6
described onlywhen required.
7.1. Checking for the power supplyP.C.B.
-Check the power supplyP.C.B. as shownbelow.
7.2. Checking for the operation P.C.B.
-Follow the (Step 1) -(Step 3) of item 7.1.
-Check the operation P.C.B. as shownbelow.
7
7.3. Checking for the mainP.C.B.
-Follow the (Step 1) -(Step 3) of item 7.1.
-Check the mainP.C.B. as shownbelow.
8
7.4. Replacement for the fan motor ass’y
-Follow the (Step 1) -(Step 3) of item 7.1.
9
7.5. Replacement for the power IC
-Follow the (Step 1) -(Step 3) of item 7.1.
-Follow the (Step 1) -(Step 3) of item 7.3.
10
This manual suits for next models
3
Table of contents
Other Panasonic Amplifier manuals
Panasonic
Panasonic System 850 User manual
Panasonic
Panasonic SU-MED640P User manual
Panasonic
Panasonic LS-400 Series User manual
Panasonic
Panasonic MINAS-BL GP series User manual
Panasonic
Panasonic LS-403 User manual
Panasonic
Panasonic WR-201E Guide
Panasonic
Panasonic Ramsa WZ-AD96M User manual
Panasonic
Panasonic WJ300C - SWITCHER/CONTROLLER User manual
Panasonic
Panasonic RAMSA WP-1200 User manual
Panasonic
Panasonic CYM7002EUC - AUTO POWER AMPLIFIER User manual
Panasonic
Panasonic CY-M9054EN User manual
Panasonic
Panasonic RAMSA WP-1200B/G User manual
Panasonic
Panasonic FX-505 C2 Series User manual
Panasonic
Panasonic FX-550L Series User manual
Panasonic
Panasonic MINAS-BL GU series Owner's manual
Panasonic
Panasonic MJE-FX501 User manual
Panasonic
Panasonic LA-A1 User manual
Panasonic
Panasonic MINAS-BL GU series User manual
Panasonic
Panasonic CY-M7052 Operating User manual
Panasonic
Panasonic LS-501 C2 Series User manual
