Pallipartners 970P User manual
User Manual
1
Thank you for choosing our Metal Detector. Please read this
manual carefully and become familiar with the function of the
detector before use. After reading, please keep it safe for future
reference.
TIPS
1. The detector is used for outdoors. There are too many
interferences indoors.
2. In the higher sensitivity range, the detector will be more
sensitive to the electromagnetic interference. By reducing
sensitivity you can get rid of interference.
3. When detecting, move the search coil at a constant speed. Let
the search coil be parallel with the ground and about 1/2 inch
from the surface, do not to swing it like a pendulum.
4. The depth indication is accurate for coin-sized objects. Large
objects or irregularly-shaped objects will reduce accuracy.
5. Most of the valuable metal objects will send consistent signals. If
the signal isn't consistent, it's mostly a false signal.
6. The Panel LCD will automatically turn off every 10 minutes. Hold
vol button for 2 seconds to lighten it again.
7. If the pinpoint mode malfunctioned, sending a signal even when
not close to any metal , lift the detector in the air, press the P-P
button once to solve the problem.
2
SPECIFICATIONS
• Operation Mode: 4+1
Motion Mode: ALL-METAL,DISC,MEMORY,JEWELRY
Non-motion Mode: PINPOINT
• Coins Depth Indication: 2’’,4’’,6’’,8’’ and+
• Sensitivity Control: 5 grades
• Target Metals Discrimination: 6 kinds
0 to 99 double digits
•
Signal Strength Indication:5 grades
•
Sound Frequency: 3 kinds of frequency indicating different
metals
•
Volume Indication: 3 grades
•
LCD Backlight: White
• Battery Indication: 4 grades
•
Turn off prompt: sound a prompt tone every ten minutes
•
Search Coil: waterproof search coil
•
Earphone Jack: 1/8 inch earphone jack
•
Power Supply: two 9V alkaline battery
ASSEMBLY
The structure of the detector is shown in the Fig.1 below.
Fig.1
3
1. Loosen the lock knob on the lower stem, take down the bolt.
install the lower stem on the search coil, and lock it tightly (See
Fig.2).
Fig.2
2. Loosen the lock nut on the middle stem, press the silver button
on the lower stem, insert to the middle stem (See Fig.3).
Fig.3
3. Loosen the lock nut on the other end of the middle stem. Press
the silver button on the upper stem, and insert it into the other
end of the middle stem (see Fig.4).
Fig.4
4
4. Adjust the length that the lower stem inserts to the middle stem.
Also, you can adjust the total length of the stem, making you
detect comfortable with your arm straight.
5. Wind the cable of the search coil around the aluminum stem,
elastic moderate, let it not sway. plug the cable plot into the
lower right of the control box, aim at the slot, and plug into the
end (see Fig.5). Note do not pull the cable, pull the plug.
BATTERY
Please use two 9V alkaline battery.
Open the battery cover and install the battery according to the
polarity sign in the battery box, let the ribbon be under the batter. If
you are not going to use the detector for a long time, please
remove the battery from the battery case.
Fig.6
5
PANEL(LCD and Button)
Fig.7
LCD
• Mode Cursor: indicate the operation mode, altogether divided
into four kinds.
• Target ID Cursor: divided into 6 categories. it is used to indicate
the target metals.
• Digital ID Cursor/Pinpoint Cursor: two digits of 01 to 99
accurately indicate the metal material. it also acts as a P-P
cursor, when P-P showing, it enters the pinpoint mode.
• Coin Depth Cursor: divided into five grades. indicates the
approximate depth of 25￠silver coin in neutral soil.
• Signal strength cursor: indicates the signal strength when in the
pinpoint mode.
• Volume cursor: indicates the volume.
• Sensitivity indication cursor: divided into five grades, sensitivity is
highest when all cursor light.
• Battery power cursor: divided into four grades, indicating battery
power. When the battery pattern is flashing, which means the
battery should be replaced.
6
Button
•VOL-(backlight) button:
VOL-(backlight) button: Short press to regulate the volume
circularly. Long press and hold the button for about 2 seconds,
and the backlight is lit for about 10 minutes.
• POWER button:
Power button: power on/off
• MODE-SENS button:
1. Press the MODE button, cycle selection in four ways.
A-M: All metal mode, the detector will respond to all metal.
DISC: Discrimination mode, in this mode you can eliminate
certain kind of metal then the detector won't respond to it.
MEMORY: Remember some kind of metals you choose, and will
only respond to this metal.
JEWELRY: Eliminate iron, it won't respond to iron, but it will
respond to other metals.
2. Press the SENS button, ( , ) buttons to adjust the sensitivity.
• ( , ) button: There are two functions.
1. Press SENS button, the sensitivity cursor will flash, and the ( , )
button is used to adjust sensitivity.
2. In DISC mode, the ( , ) button is used to set the discrimination
targets.
• P-P button: Press the “P-P” button, and the detector will convert
to PINPOINT mode, to locate the target accurately. Press the
"P-P" button once again, to exit the PINPOINT mode.
QUICK- START
1. Lay the detector
Put the detector on a wooden or plastic table, and let the search
coil stretch out of the table about 30cm, keep away from walls,
ceilings and floors, turn off all kinds of electrical appliances that
will cause electromagnetic interference, remove watches and
rings from hands. (see Fig 8)
7
Fig.8
2. Turn on
Press the POWER button, the detector will sound two moo tones,
and all LCD patterns will be lit for a moment. And the detector is
set by default last shutdown.
3. ALL METAL mode test
Press the MODE button, the A-M cursor will light. Sweep six
sample metals (iron nail, 5￠nickel coin, pull-tab, 1￠Zinc coin,
10￠copper coin and 25￠silver coin)above the search coil 7-
10cm respectively.
a) The detector sounds three different tones in turn.
b) The depth cursor indicates the second grade.
c) The target cursor flashes respectively. The digital cursor shows
the corresponding number.
8
As shown in the table:
Sample
Iron
nail
5￠
nickel
coin
Pull-tab
1￠
zinc
coin
25￠
copper
coin
50￠
silver
coin
Tone
Low
tone
Low
tone
Middle
tone
Middle
tone
High
tone
High
tone
Identification
Cursor
indication
Digital cursor
indication
10-40
41-50
55-70
72-75
80-83
86-88
(See Fig.9 take iron nail as an example)
4. DISC mode test
a) Press the MODE button again, the DISC cursor is lighted.
b) Press ( , ) button, set the discrimination target, to eliminate
some metals which do not need to be detected. For example, to
reject three kinds of metals such as iron, nickel and pull-tab.
Press the ( , ) button, making the three target cursors on the
left removed.
c) Sweep the six metal samples about 7 to 10cm above the search
coil in turn.
d) When sweeping the iron nail, 5￠nickel coin and pull-tab, the
detector will not respond, they are eliminated.
e) When sweeping the other three samples, the corresponding
target cursor flashes, and the digital cursor shows the
Table of contents
Popular Metal Detector manuals by other brands
Steinberg Systems
Steinberg Systems SBS-MD-12 user manual
GOLDEN MASK
GOLDEN MASK 5 user guide
Grizzly
Grizzly YM 203 manual
Fisher Research Labs
Fisher Research Labs 1280-X Aquanaut operating manual
Treasure Cove
Treasure Cove Vibra-Probe 560 quick guide
Accurate Locators
Accurate Locators XL16 IMAGER user guide