Pallas WB-215 User manual
User’s Instructions
Booklet
PallasWB-215
DigitallyOperatedRechargeableBTE
PersonalSoundAmplifier
TABLE OF CONTENTS:
Introductions.............................................................. 3
Getting started........................................................... 6
Charging the device.................................................. 8
Indication for use....................................................... 9
Wearing the device..................................................... 10
Regulatory compliance............................................. 12
Maintenance & Repair service.................................. 13
Use & care................................................................... 14
Limited warranty........................................................ 15
Product & technical information.............................. 16
- 1 -
Pallas WB-215
Digitally operated rechargeable BTE Personal Sound
Amplier is a wearable electronic hearing amplier
that ts in either ear, intended to amplify and
modulate environmental sounds for the wearer.
You have our commitment to continue provide you with the
support for using this device you just bought. You are
encouraged to share with us your experience of using the
device.
It is important for you to read this user’s instructions booklet
before using your device. Please read and adhere to the
warning statements, and follow the instructions when
operating the device. Be sure to keep this user’s instructions
booklet for future reference.
Warning:
Small parts choking hazards, not for children and pets.
- 2 -
Introductions
This user’s booklet is for the instructions of operating the
Pallas WB-215 digitally operated rechargeable BTE
Personal Sound Amplier
To get acquainted with the Pallas WB-215 digitally operated
Personal Sound Amplier you may want to wear the device
and try listening to the radio and watching television, and
start conversations with the others. This will help you get
adjusted to the device for identifying sounds and voices
surrounding you. When you rst start wearing the device
you should concentrate particularly on those sounds and
voices you want to hear, practice with the device to pick
them up from one to another. It is important to recognize
your own voice thru the use of your Pallas WB-215 digitally
operated Personal Sound Amplier, that way you will learn
how to keep from speaking too loud while wearing the
device.
Important:
When not using your Pallas WB-215 digitally operated
Personal Sound Amplier turn o the device, this will help
save battery power.
- 3 -
This set of device you just purchased consists of one Pallas
WB-215 digitally operated rechargeable BTE Personal Sound
Amplier unit, two ange ear tips, three regular silicone
rubber ear tips, one USB power cord, one multi-voltage
[100-240 Volt] UL certied 2x at-pins transistor AC power
adapter, and a user’s booklet.
- 4 -
Illustrations below indicates the function of all the device
controls intended for user adjustment.
- 5 -
Digital
Volume
controllers
Microphone
Silicone
ange
ear tip
Flex
audio
wire and
ear hock
ON/OFF
switch
Receiver
end
[speaker]
USB power
socket for
charging up
the device
LED
battery
power
indicator
lamp
GETTING STARTED:
Turn on and turn o the device:
Locate the ON/OFF switch on the device casing, slide it to its
“ON” position to turn on the device; slide same switch to its
“OFF” position to turn o.
Regulating digitally the amplied sounds of the device
sound amplication unit:
There are two buttons on the back of the device casing for
regulating sound volume - one for digitally turning “UP” the
amplied sounds and the other for digitally turning “DOWN”
the amplied sounds. Through using the nger tip of your
index nger to press between these buttons will digitally
ne tune the amplied sounds to your desired level. See
illustrations below.
- 6 -
Turning
up
Turning
down
Charging the device:
The device is operated by a rechargeable Ni-MH battery
that built-in the device casing to be charged up by the USB
power cord. User may either choose to charge up the device
by connecting the USB transistor AC adapter to alternating
current of the wall outlet, or directly connect the USB power
cord to any equipment installed with USB power outlet.
Since this device is rechargeable, there are no needs of
replacing batteries.
1. To charge the device you will need to rstly connect the
USB power cord to the device USB power socket which is
located underneath the ip-open silicone rubber stopper.
See illustration below.
- 7 -
Flip-open
silicone rubber
stopper
USB
power
plug
USB
power
socket
Charging the device (cont’d):
2. When connecting directly to the wall the USB power cord
is require to into the USB socket of the transistor AC adapter;
follow the illustrations below to connect.
3. When connecting to an USB outlet the USB transistor AC
adapter is NOT required to install; follow the illustrations
below to connect.
- 8 -
Table of contents
