Outlook EBMF3 User manual
Thank you for choosing this product! We strive to provide you with the
best quality products and services in the industry. Should you have any
Model：EBMF3
V1.0
TV Wall Mount
Instruction Manual
IMPORTANT SAFETY INFORMATION
Tools Needed (Not lncluded)
Stud finder
Tape measure Pencil Drill
7/32 in.(5.5mm)
Wood drill
3/8 in.(10mm)
Concrete drill
3/8in.(10mm)
Socket wrench
1/2in.(13mm)
Socket wrench Screwdriver
Hammer
Supplied Parts
[01] X1 PC [02] X2 PCS
1
Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete block
and brick walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Supplied Hardware
Hardware for Attaching TV Bracket to TV
Washers
M8
x4
A2
Spacers
L5mm
Spacers
L10mm
x4 x8 x8
Bolt
M6 x 15mm
M6 x 30mm
x4x4
D1 D2
x4 x4x4
E1 E2 F
Bolt
M8 x 15mm
M8 x 45mm
Bolt
M4 x 30mm
C1 C2
Washers
M6
B
Hardware for Attaching Wall Plate to Wall
Lag Screws
M8X65
x4 x4
A1
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
A3
Wall
Anchor
2
D1
B
E1
Step 1 Measure VESA and Check TV Bolts
Check TV bolts
When attaching brackets to the flat
screen, be careful not to over
tighten bolts and be sure that bolts
do not bottom out in the mounting
holes.
Too Short Too Long
Correct Correct
Hand thread bolts into the threaded inserts on
the back of your TV to determine which bolt
diameter (M4, M6, or M8) to use.
Width
Height
Measure the distance between
the holes located at the back of
your TV (these measures may
form the shape of a square, or a
rectan gle) and check that these
taken measures are within the
VESA(*) range for this wall
mount.(*) VESA: International
standard established by the TV
manufacturers used to determine
if LCD/LED TVs are compatble
with wall mounts.
FLAT BACK TV
(UNIVERSAL TV PLATE)
Step 2 Attach the TV Brackets to the TV
3
or
D2/F
B
C1/C2
E2
C1/C2
ROUND BACK TV
(UNIVERSAL TV PLATE)
First, make sure the diameter of the bolt(D1-F) fits your TV. Then, please see the
diagram above. You will need to thread the bolt into the TV using the washer (B) and
spacer (C1 or C2) if necessary with a screwdriver(Not included). Please make sure the
TV brackets[02] are vertically centered and level with each other.
Step 3
STEP 3A
X
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
Attach Wall Plate to Wall
Wood Stud Option
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
● Drywall covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
WARNING:
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag screws [A1]. Tighten the lag screws [A1] only
until the washers [A2] are pulled firmly against the wall plate
[01]
.
4
or
ø7/32 in.(5.5mm)
3A-1 3A-2
3A-3 3A-4
7/32 in.(5.5mm)
Wood Drill
2 9/16 in.(65mm)
A1 A2
STEP 3B
Avoid potential personal injury or property damage!
DO NOT
over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until
the washers [A2] are pulled firmly against the wall plate
[01]
.
WARNING:
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
Drywall covering the wall must not exceed 5/8 in. (16
mm)
Wall
Anchor
A3
Solid Concrete or Concrete Block Option
Ensure marking at
the center of the
stud. Center line
Drill 4 pilot holes using
a 7/32 in. (5.5mm)
Wood Drill diameter
drill bit.Make sure the
depth is not less than
2 9/16 in.(65mm).
Mount the wall plate using 4
sets of M8X65 lag screws A1
and washers A2 with a 1/2
in.socket wrench(not included).
1/2in.(13mm)
socket wrench
Use a stud finder (not included) to
locate wood stud. Mark the edge
and center locatons.
5
3B-1 3B-2
3B-3 3B-4
3/8 in.(10mm)
Concrete Drill
ø3/8 in.(10mm)
2 3/4 in.(70mm)
A2
A3 A1
WARNING:
● Mount the wall plate [01] directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Position the wall plate at your desired
height, level the wall plate and mark the 4
pilot hole locations.
Drill 4 pilot holes
using a 3/8
in.(10mm) diameter
drill bit.Make sure the
depth is not less than
2 3/4 in.(70mm).
Install wall plate using lag screws [A1], washers
A2 and anchors A3. Be sure the anchors [A3] are
seated flush with the concrete surface. Tighten
the lag screws [A1] only until the washers [A2]
are pulled firmly against the wall plate [01] . DO
NOT over-tighten the lag screws [A1].
Use the hammer to knock
anchors [A3] into the wall.
6
Hang the TV onto the wall plate
STEP 5
Level Adjustment
STEP 4
If needed, the TV can be leveled
Tilt
adjustment
Locking
7
Table of contents
