Outback OUT370665 User manual

Photographs are not to scale.

Specifications subject to change

without prior notice.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open barbecue lid or hood.

4. If odour continues, discontinue use and contact

your local dealer.

FOR YOUR SAFETY

1. Do not store or use petrol or other flammable

vapours or liquids in the vicinity of this or any

other appliance.

2. A gas bottle not connected for use must not be

stored in the vicinity of this or any other

appliance.

Assembly and Operating Instructions for

Outback® Signature Stainless Steel Flame Tower

OUT370665

PH300

0063 0558

WARNlNG SAFETY RULES

PLEASE READ THE FOLLOWING SAFETY RULES PRlOR TO OPERATION

OF THE HEATER.

WARNlNG

1) For use outdoors or in amply ventilated areas.

2) An amply ventilated area must have a minimum of 25 % of the

surface area open.

3) The surface area is the sum of the walls surface.

WARNING Improper installation, adjustment, alteration, service

or maintenance Can cause injury or property damage. Read the

installation, operating and maintenance instructions thoroughly

before installing or servicing this equipment.

WARNING

xThis appliance must be installed and the gas cylinder stored in accordance with the

regulations in force;

xDo not obstruct the ventilation holes of the cylinder housing;

xDo not move the appliance when in operation;

xShut off the valve at the gas cylinder or the regulator before moving the appliance;

xThe tubing or the flexible hose must be changed within the prescribed intervals;

xUse only the type of gas and the type of cylinder specified by the manufacturer;

The LP tank used with your patio heater must meet the following requirements:

Purchase LP tanks only with these required measurements:

(31.8cm) (diameter) x 58cm) (tall) with 15kg capacity maximum.

xIn case of violent wind particular attention must be taken against

tilting of the appliance;

ASSEMBLY PARTS

Tools needed:

Philips screwdriver w/ medium blade

Spray bottle of soap solution for leakage test

Quantity varies according to model purchased. Specifications subject to change

without prior notice.

Parts List:

Reflector

Flame Screen

Glass Tube

Protective Guard

Upper Support

Black Silicone Ring

Side Panel

Front Panel

Block Belt

Lower Support

Control Box Assy

Gas Hose

Wheel Assembly

Bottom Plate

NOITPIRCSEDTRAPYTITNAUQ

Flame Screen

Gas Hose

Control Box Assy

Lower Support

Block Belt

Wheel Assembly

Bottom Plate

NOITPIRCSEDTRAPYTITNAUQ

Reflector

Glass Tube

Upper Support

Black Silicone Ring

Protective Guard

Side Panel

Front Panel

ASSEMBLY PARTS

HARDWARE CONTENTS (shown actual size)

AA BB

Wing nut

Qty. 3 Small flat

Qty.

DD EE

Qty. 42

Stud

Qty. 3

Philips

Qty. 1

Qty. 4

GG II

Qty. 4

Qty. 1

Flange

nut

Qty. 4

Qty.

Knob

Qty. 1

MM NN

Qty.1

Chain

Qty.1

Long Stem Lighter

Qty.1

AA Battery (1.5 V)

Qty.1

PARTS

Quantity varies according to model purchased. Specifications subject to change

without prior notice.

2270 mm

900 mm

650 mm

730 mm

Reflector

Glass Tube

Flame Screen

Protective Guard

Upper Support

Front Panel

Side Panel

Lower Support

Bottom plate

ASSEMBLY

IMPORTANT!

Whilst every care is taken in the manufacture of this product, care must be taken

during assembly in case sharp edges are present.

Please read the Important Information section carefully before assembly.

1

2

Hardware Used

EE FF II

1. Assemble the wheel assembly to the bottom plate. Fix the wheel assembly to the bottom

plate using 4pcs bolt M6X12 and 4pcs lange nut M6.

x 4 x 4 Wrench x 1

Bolt M6 X 12 M6 Flange nut

2-1.Unscrew the switch button, load small battery, tighten the switch button.

2-2. Insert the pins of the base to the holes of lower support, press to secure the pins. Using

4pcs screw M5x12 to secure the lower support and base.

Insert the pins of the control box assy to the holes of upper support, press to secure the pins.

Using 4pcs screw 3/16” screw to secure the upper support and control box assy.

Hardware Used

GG JJ

x 4 Philips

screwdriver x 1

Screw M5 X 12 DD x 4

3/16” Screw

AA Battery (1.5 V)

3

3. Assemble block belt. Fix the block belt to the 2pcs of lower support behind the front door,

using 2pcs screw M5X12.

Hardware Used

JJ x 1

Philips

screwdriver

GG x 2

Screw M5 X 12

4. Assemble the middle support.Insert the 4pcs upper support to the lower support. Secure

them with 8pcs screw 3/16”.

Hardware Used

DD JJ

x 8 x 1

Philips

screwdriver

3/16” Screw

5

5. Assebmle the flame screen to the upper support.Secure the flame screen to the upper support

using 8pcs screw “3/16”.

Hardware Used

DD JJ

x 8 Philips

screwdriver

3/16” Screw x 1

Hardware Used

6. Assemble the reflector onto the flame screen. Screw the 3pcs stud on the flame screen,

put 3pcs washer 6 onto the top of stud,then put the reflector onto the stud, secure them with

3pcs washer 6 and 3pcs wing nut.

x 3 x 3

x 6

AA BB

Wing nut CC Stud

To aid in installation

place black silicone

ring on the middle

plate and then

install glass tube.

Ensure the rim of

the glass tube sits

firmly in the black

silicone ring.

BLACK SILICONE

RING

7. Carefully install the glass tube by lifting up and inserting through the center hole in the

upper plate. Ensure the black silicone ring is attached to the lower edge of the glass tube

as illustrated. Slide the glass tube through the hole of the lower plate cover and onto the

middle plate. Check and ensure that the glass tube is positioned properly and is completely

covering the center hole of the middle plate.

WARNING! The black silicone ring must be in place prior to operating the heater.

8. Assembly the protective guard.Hang the hooks of the protective guard onto the holes in

supports.

Secure the protective guards with fixing brackets with 4pcs 3/16" screws.

Hardware Used

DD JJ

x 4 Philips

screwdriver

3/16” Screw x 1 HH Fixing

Bracket x 4

9. Attachthe threesidepanels to the heater using18pcsscrew3/16”.

Note : Do not cover the frontsidewherethecontrolknobis.

Hardware Used

DD JJ

x 18 Philips

screwdriver

3/16” Screw x 1

10. Installthe knob to M4x10screw.Hang the chain to the hole on the controlbox assyand

put the pothook of frontpanel to the holes of bottomplate.

Hardware Used

x 1

KK Knob

x 1

Philips

screwdriver

Screw M4 X 10 x 1

MM Chain

This manual suits for next models

Table of contents

Other Outback Patio Heater manuals

Outback

Outback OUT370610/PH200T User manual

Outback

Outback OUT370663/PH500 User manual

Outback

Outback OUT370665/PH300 User manual

Outback

Outback PH04 User manual

Popular Patio Heater manuals by other brands

empasa

empasa HMXD-E-NHS operating instructions

Sunred

Sunred Indus manual

HEAT1

HEAT1 ECO pro-line 2300W instructions

Heatmaxx

Heatmaxx SRPH98 instruction manual

Sunjoy

Sunjoy A30600640 manual

Event Furniture

Event Furniture 16091 Operating & safety guide

Prem-I-Air

Prem-I-Air EH1462 manual

Blumfeldt

Blumfeldt 10028637 manual

Sunjoy

Sunjoy L-PH011PSS-2 owner's manual

Melissa

Melissa 670-202 user guide

Quality Heating

Quality Heating THE-12DW manual

DCS

DCS PHFS-P4 Use and care and installation guide

EUROM

EUROM 334241 instruction manual

Lava Heat

Lava Heat Venetian owner's manual

EHS Ltd.

EHS Ltd. HQH-2000W instruction manual

VONROC

VONROC ALICUDI PH515AC Original instructions

OZONA

OZONA Heatflow IF010997 Safety instructions and operation manual

theBBQshop

theBBQshop 51611010 Safety, Installation, Operation and Maintenance