OSOTEK HotWave 2104A.11 User manual
OSOTEK HotWave Wet Dry Vacuum User Manual •01
Manuel d'utilisateur de l'aspirateur sec et humide OSOTEK HotWave •23
1
Safety Instructions
Household use only.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE), Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury.
WARNING–To reduce the risk of fire, electric shock, or injury.
•Use Indoor Only.
•Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.
•Use only as described in this manual. Use only manufacturer’s recommended attachments
•To provide continued protection against risk of electric shock, connect to properly grounded outlets only.
•Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
•Any servicing should be done with the appliance disconnected from the supply circuit.
•Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from
heated surfaces.
•Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
•Do not handle charger, including charger plug, and charger terminals with wet hands
•Risk Of Injury. Brush May Start Unexpectedly. Keep the power off Before Cleaning or Servicing.
•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
•Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
•Use extra care when cleaning on stairs.
•Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
•Do not use without filter in place.
•Turn off all controls before unplugging.
•Always turn off this appliance before connecting or disconnecting motorized nozzle.
•Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your
finger on the switch or energizing appliance that have the switch on invites accidents.
•Have servicing performed by a qualified repair person using only identical replacement parts.This will ensure that the safety of the product is maintained.
•Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated in the instructions for use and care.
•This appliance contains batteries that are only replaceable by skilled persons.
•The appliance is only to be used with the power supply unit provided with the appliance.
•This vacuum is for indoor use only. Do not use or install it in outdoor, industrial, or commercial environments. Do not use the base station in humid environments such as
bathrooms.
2
•Do not touch the plug or any part of the vacuum with wet hands.
•A hazard may occur if the appliance runs over the supply cord.
•The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.
•If the power cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
•Neither use the vacuum to pick up flammable or explosive liquids such as gasoline, nor other liquids such as water or toxic liquids like bleach, ammonia, and drain cleaners.
•To avoid potential danger, do not run the vacuum on the power cords when using it.
•To reduce the risk of fire, explosion, or personal injury, check before use to make sure the lithium battery and power cord are undamaged. Do not use the vacuum if either
the lithium battery or power cord is damaged.
•The main body and the floor brush of the vacuum are electrically conductive and should not be immersed in water or other liquids.
•Clean the dirty water tank in time to avoid the decrease of suction and overheating of the motor caused by obstruction. Otherwise, the service life of the vacuum may be
affected. Do not use the vacuum if the roller brushbar, the dirty water tank, and the filter are not installed in place.
•Do not lift the vacuum when adding water to it at the base station.
•Make sure to turn off the vacuum before replacing the roller brushbar.
•Do not use the vacuum to clean up toner used in laser printers and copiers, as toner may cause fire or explosion.
•Do not use the vacuum to pick up smoking or burning materials such as charcoal, cigarette butts, or matches.
•Do not use the vacuum to pick up sharp or hard objects, such as glass, nails, screws, or coins, which may damage the vacuum.
•Do not use the vacuum to clean stains of thick oily substances, strong adhesives, or dyes, such as shoe polish, paints, and pigments.
•Keep hair, loose clothing, fingers, and other parts of the body away from the vacuum’s openings and moving parts.
•Do not put any object into the vacuum's openings, nor use the vacuum with any opening blocked. Keep free of dust, lint, hair, or other items which may reduce airflow.
•Do not shake the vacuum up and down or hit it violently to prevent dirty water from flowing into the motor.
•Do not lift or move the vacuum while the motor is operating, nor tilt it to one side or lay it flat to prevent dirty water from entering the motor.
•Do not place the vacuum on unstable surfaces such as chairs or tables to prevent damage or personal injury caused by its falling off. If the vacuum malfunctions because
of being knocked over or damaged, please contact the authorized service department. Never attempt to disassemble the vacuum on your own.
•Do not block the drying air outlet on the base station to avoid malfunctions.
•After washing the cleaning tray and the accessory container clean, thoroughly dry them before reinstalling them to the base station.
•After cleaning the roller brushbar, the filter, and the cleaning brush, thoroughly dry them before putting them into the accessory container to prevent odors.
•Do not rinse the base station with water.
•Use clean tap water when adding water to the water tank of the base station.
•Do not charge or store the vacuum near heat sources or in humid areas, such as by a radiator or in a kitchen or bathroom.
•Only use replacement parts that are approved by OSOTEK.
•Do not repair the vacuum on your own when it breaks down or has problems like electric leakage, overheating motor, making unusual sounds, overheating main body, giving
off bad odors, or weak suction.
•Do not use any third-party battery or power cord. The vacuum can only be used with the model A020H100CS/A020H100CS.1base station.
•Fire Hazard Warning: Do not apply any type of fragrance to the vacuum's filter. These types of products are known to contain flammable chemicals which may cause the
vacuum to catch fire.
•The base station can only be used to dry the roller brushbar, the filter, and the cleaning brush of this vacuum.
•Do not use any third-party battery or power cord. Only use the A020H100CS/A020H100CS.1 base station provided with the appliance.
•Do not use the appliance at ambient temperature above104°F(40°C) or below41°F (5°C).
3
•Storage Temperature: 32°F (0°C) to 104°F(40°C).
Battery Pack and Charging
•Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery
pack.
•Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
•When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,keys, nails, screws or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
•Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns.
•Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of
injury.
•Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 266°F(130°C)may cause explosion.
•Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at
temperatures outside of the specified range may damage the battery and increase the risk of fire.
•Battery charging can only be performed at the ambient temperature between 41°F(5°C) to104°F(40°C). Excessively high or low temperature may extend the battery
charging time, and even damage the battery. The normal charging of this product takes about 4-5 hours, so as to fully activate the battery.
•For use only with OSOTEK A020H100CS/A020H100CS.1 base station.
SAVE THESE INSTRUCTIONS
Transportation
•It is recommended to transport the vacuum cleaner in its original packaging.
Precautions for Using Cleaning Solution
•Please use the specified cleaning solution. Please use the cleaning solution as instructed to prevent any danger caused by excessive bubbles entering the motor.
•Keep the cleaning solution out of reach of children. In case of contact with eyes, rinse immediately with plenty of water. In case of accidental ingestion, seek medicaladvice
immediately.
•Please comply with local environmental regulations when disposing of the dirty water and cleaning solution.
⎓Direct current
～Alternating current
Power Botton
4
Product Overview
Vacuum
Voice Control Button
Handle Release Button
Water Inlet
Charging Contacts
Mode Switch Button
Power Button
Handle
Display
Clean Water Tank
(Non-detachable)
Dirty Water Tank
Release Button
Dirty Water Tank
Roller Brushbar Cover
Release Button
Floor Brush
Self-cleaning Button
Hot Water Adding Button
Dust
Compartment
5
Water Tank Cover Release Button
Accessory Drying Button/LED Indicator
Charging Contacts
Accessory Compartment
(Accessory Container Included)
Water Adding Connector
Water Tank (Detachable)
Water Tank Indicator
Cleaning Tray (Detachable)
Drying Air Outlet
AC Power Cord Port
Base Station
6
Accessory List
Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product
enhancements.
Filter
（Replacement）× 1
Cleaning Brush
（Rotate the handle of the cleaning
brush to remove the blade.）
Roller Brushbar
（Replacement）× 1
Handle Water Tank
Power Cord Measuring cup Cleaning Solution
20ml
40ml
60ml
80ml
100ml
120ml
150ml
7
Installing the Handle
1. Insert the handle into the port on the vacuum. The handle is installed when you
hear a click. Then make sure the handle is secured in place.
2. The vacuum is in sleep mode when it is used for the first time or has not been
used for a long time (30 minutes). In this case, the vacuum will not be charged
when it is placed on the base station. You can press any button on the vacuum
to activate it.
1. To remove the handle, insert a screwdriver into the hole on the back of the
vacuum as illustrated to press the handle release button, and simultaneously
pull the handle upwards vertically.
How to Install
Click into Place
8
2. Press and hold the release button on the water tank cover and simultaneously
rotate the cover to open it. Then add clean tap water to the water tank and
install the cover back. It is secured in place when you hear a click.
Notes:
•Please use the special cleaning solution for this product and inject it into the
base station water tank with reference to the standard dilution ratio of the
cleaning solution.
•It is forbidden to add any liquid other than tap water and original cleaning
solution to avoid danger.
Click into Place
Installing the Base Station
1. Place the base station against a wall, and connect the power cord to it. Store
the power cord in the back of the base station.
Note:
Do not place the vacuum and the base station near heat sources or in humid
areas, such as by a radiator, in a kitchen, or in a bathroom.
9
3. Put the water tank onto the base station. Open the accessory compartment,
and place the spare roller brushbar, the spare filter, and the cleaning brush into
the compartment.
4. After the base station is powered on, place the vacuum on it to charge.
Notes:
•Fully charge the vacuum before first use and after each use. The total
charging time is about 5 hours.
•Once the vacuum is fully charged, the display will turn off after 20 seconds
and the vacuum will then enter the energy-saving mode.
•Working at the turbo mode for a prolonged period will cause the battery to
heat up, and the charging time may increase or the battery level may not
grow in a short time during charging. This is normal.
This manual suits for next models
1
Table of contents
Languages:
Other OSOTEK Vacuum Cleaner manuals
