OSKAB RHP67000/1LIN/1 User manual
1
RHP67000/1LIN/1
RHP67000/1LPN/1
Cooker Hood
Hotte de cuisson
EN
Instruction manual
2
FR
Manuel d'instructions
15
I
S
RHP97000/1LIN/1
RHP97000/1LPN/1
2
CONTENT
1. Safety instructions 3
2. Installation 5
3. Start using your cooker hood 8
4. Troubleshooting 9
5. Maintenance and cleaning 10
6. Environment protection 14
3
SAFETY INSTRUCTIONS
This manual explains the proper installation and use of your cooker hood, please read
it carefully before using even if you are familiar with the product. The manual should
be kept in a safe place for future reference.
Never to do:
● Do not try to use the cooker hood
without the grease filters or if the filters
are excessively greasy!
● Do not install above a cooker with a
high level grill.
● Do not leave frying pans unattended
during use because overheated fats or
oils might catch fire.
● Never leave naked flames under the
cooker hood.
● If the cooker hood is damaged, do not
attempt to use.
● Do not flambé under the cooker hood.
● CAUTION: Accessible parts may
become hot when used with cooking
appliances.
● The minimum distance between the
supporting surface for the cooking
vessels on the hob and the lowest part
of the cooker hood. (When the cooker
hood is located above a gas appliance,
this distance shall be at least 65 cm)
● The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels.
Always to do:
● Important! Always switch off the
electricity supply at the mains during
installation and maintenance such as
light bulb replacement.
● The cooker hood must be installed in
accordance with the installation
instructions and all measurements
followed.
● All installation work must be carried
out by a competent person or qualified
electrician.
● Please dispose of the packing
material carefully. Children are
vulnerable to it.
● Pay attention to the sharp edges
inside the cooker hood especially
during installation and cleaning.
● Make sure the ducting has no bends
sharper than 90 degrees as this will
reduce the efficiency of the cooker
hood.
● Warning: Failure to install the screws
or fixing device in accordance with
these instructions may result in
electrical hazards
● Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
4
Always to do:
● Always put lids on pots and pans
when cooking on a gas cooker.
● When in extraction mode, air in the
room is being removed by the cooker
hood. Please make sure that proper
ventilation measures are being
observed. The cooker hood removes
odours from room but not steam.
● There shall be adequate ventilation of
the room when the cooker hood is
used at the same time as appliances
burning gas or other fuels.
● Cooker hood is for domestic use only.
● If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
● This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge if they
have been given supervision or
instruction concerning use of the
appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Always to do:
● Caution: The appliance and its
accessible parts can become hot
during operation. Be careful to avoid
touching the heating elements.
Children younger than 8 years old
should stay away unless they are
under permanent supervision.
● There shall be adequate ventilation of
the room when the cooker hood is
used at the same time as appliances
burning gas or other fuels.
● There is a fire risk if cleaning is not
carried out in accordance with the
instructions
● Regulations concerning the discharge
of air have to be fulfilled.
● Clean your appliance periodically by
following the method given in the
chapter MAINTENANCE.
● For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this
instruction manual.
● Regarding the details about the
method and frequency of cleaning,
please refer to maintenance and
cleaning section in the instruction
manual.
● Cleaning and user maintenance shall
not be made by children without
supervision.
● When the cooker hood and
appliances supplied with energy other
than electricity are simultaneously in
operation, the negative pressure in the
room must not exceed 4 Pa
(4 x 10-5 bar).
5
INSTALLATION (VENT OUTSIDE)
If you have an outlet to the outside, your cooker hood can be connected as below
picture by means of an extraction duct (enamel, aluminum, flexible pipe or inflammable
material with an interior diameter of 150/120mm)
1. Before installation, turn the unit off and unplug it from the outlet.
2. The cooker hood should be placed at a distance of 65~75cm above the cooking
plane for best effect.
3. Install the hook on a suitable place once the installation height is fixed, and keep it
in line. The fixed position of the inside chimney bracket is the place of chimney.
See pic 2.
4. Fix the outside chimney bracket on the outside chimney, and be sure that the inside
chimney can be adjusted the height in it freely as well as fixing the expansion pipe.
Afterwards, install the expansion pipe and chimney on the cooker hood. See Pic 3.
6
5. Put the cooker hood on the hook. See Pic 4.
6. Adjust the height of the inside chimney to the position of the inside chimney bracket
and fix on it by screw, after adjusting the position, fix the body with safety screw.
See Pic 5.
Note: The two safety vents are positioned on the back housing, with diameter of
6mm.Lay the expansion pipe to the wall outlet. Fix the expansion pipe with the cable
tie (1) on the wall-outlet if it is aluminium foil pipe.
MOUNTING OF THE V-FLAP
If the cooker hood does not have an assembled V-flap 1, you should mount the half-
parts to the its body.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6
• a pin 3 should be top oriented;
• the axis 4 should be inserted in the holes 5 on body;
• repeat all the operations for the 2nd half-part
Cable tie
Safety screw
Outside chimney
Outside chimney bracket
Inside chimney
Expansion pipe
Note:
The following models include the v-flap: RHP67000/1LIN/1, RHP67000/1LPN/1,
RHP97000 /1LIN/1, RHP97000/1LPN/1
7
HINTS FOR EXHAUST DUCT INSTALLATION
The following rules must be strictly followed to obtain optimal air extraction:
Keep expansion pipe short and straight.
Do not reduce the size or restrict expansion pipe.
When using expansion pipe always install the pipe pulled taut to minimize
pressure loss.
Failure to observe these basic instructions will reduce the performance and
increase noise levels of the cooker hood.
Any installation work must be carried out by a qualified electrician or competent
person.
Do not connect the ducting system of the hood to any existing ventilation system
which is being used for any other appliance ,such as warmer tube, gas tube, hot
wind tube.
The angle of the bend of the expansion pipe should not be less than 120º; you
must direct the pipe horizontally, or, alternatively, the pipe should go up from the
initial point and should be led to an outer wall.
After the installation ,make sure that the cooker hood is level to avoid grease
collection at on end.
Ensure the expansion pipe selected for installation complies with relevant
standards and is fire retardant.
Note: The product is provided with v-flap accessory. This accessory is not mandatory
for installation, operation and use of the product.
8
WARNING:
For safety reason, please use only the same
size of fixing or mounting screw which are
recommended in this instruction manual.
Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.
Start Using Your Cooker Hood
LED touch control
LED touch control has five buttons, see pic.
(Decrease), (Increase), (Lamp), (Timer), (Power)
1. Power-on: After connecting the cooker hood to the main supply, the backlight of
button will turn on. The backlight will turn off after 30s without any operation and the
cooker hood will enter into stand-by mode.
2. (Power) button:
2.1. Press (Power) button, the backlight of button will be on and the hood will work at
the mid speed, and the light will be on. The backlight of the buttons (Decrease),
(Increase), (Lamp), and (Power) will be on. Press (Power) button again, the backlight
of button will be off and the cooker hood will be turn off and return into stand-by mode
and operate by the circle.
2.2. Those buttons of (Decrease), (Increase) and (Lamp) button could be operated
without pressing the (Power) button. Press one of those buttons, the cooker hood will
work according to the pressed function button. Press (Power) button, the cooker hood
will be turn off without any functions.
3. (Lamp) button:
Press (Lamp) button, the backlight of button and the lights will be on. Press again, the
lights will be off. The lights run circularly.
4. (Increase) button:
4.1 Press (Increase) button, the backlight of button will be on, the cooker hood starts
to work at the low speed. the LED display will display “1”,
4.2 Press (Increase) button again when it is working on the low speed, the cooker
hood works at the mid speed and the LED display will display “2”,
4.3 Press (Increase) button again when it is working on the mid speed, the cooker
hood works at the high speed and the LED display will display “3”,
9
4.4 Press (Increase) button again when it is working on the high speed, the cooker
hood will still work at the high speed.
5. (Decrease) button
Press (Decrease) button, the cooker hood will decrease one speed, and the display
will show the current working speed. When press (Decrease) button again when it is
working on the low speed, the cooker hood will turn off and the backlight of the
(Decrease) button will be off.
6. (Timer) button:
6.1 The (Timer) button works when the motor and light is on only. The timer setting is
5mins and could be repeat setting. When the time is up, the cooker hood will be turn
off and the light will be off.
6.2 When the timer is set, if adjusting the speeds, the timer will re-calculate the
working time.
TROUBLESHOOTING
Fault
Possible Cause
Solution
Light on, but motor
does not work
Fan switch turned off
Select a fan switch position.
Fan switch failed
Contact service center.
Motor failed
Contact service center.
Light does not
work, motor does
not work
House fuses blown
Reset/Replace fuses.
Power cord loose or
disconnected
Refit cord to power outlet. Switch
power outlet on.
Oil leakage
One way valve and the air
ventilation entrance are not
tightly sealed
Take down the one way valve
and seal with sealant.
Leakage from the connection of
U-shaped section and cover
Take U-shaped section down
and seal.
Lights not working
Broken/Faulty globes
Replace globes as per this
instruction.
Insufficient suction
The distance between the
cooker hood and the gas top is
too far
Refit the cooker hood to the
correct distance.
The Cooker hood
inclines
The fixing screw not tight
enough
Tighten the hanging screw and
make it horizontal.
NOTE:
Any electrical repairs to this appliance must conform to your local, state and
federal laws.Please contact the service centre if in any doubt before
undertaking any of the above.Always disconnect the unit from the power source when
opening the unit.
10
MAINTENANCE AND CLEANING
Caution:
• Before maintenance or cleaning is carried out, the cooker
hood should be disconnected from the main power
supply. Ensure that the cooker hood is switched off at the
wall socket and the plug removed.
• External surfaces are susceptible to scratches and
abrasions, so please follow the cleaning instructions to ensure the best possible
result is achieved without damage.
GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially
when cleaning.Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on
the surfaces.
STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g.weekly) to ensure long life
expectancy.Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may
be used.
NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any
unsightly crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is
clean and well wrung before cleaning. Use a dry soft cloth to remove any excess
moisture left after cleaning.
Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household
detergents or products containing abrasives,as this will affect the appliance
appearance and potentially remove any printing of artwork on the control panel and
will void manufactures warrantee.
This manual suits for next models
3
Table of contents
Languages:
