Ortech OE-316 User manual

WARNING

LED Exit Signs

MODEL OE-316

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.

Electrical products can cause death or injury, or damage to property.

If in any doubt about the installation or use of this product, consult a competent electrician.

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY

A QUALIFIED ELECTRICIAN.

1. LED Exit Signs are suitable for indoor use only. DO NOT use outdoors

2. Please keep the LED Exit Signs away from any corrosive substance

3. LED Exit Signs can only be installed by a qualified electrician

4. Before installation or maintenance, please disconnect the power at fuse or circuit breaker to

prevent electric shock

Instruction Manual

1-888-543-6473

1-888-541-6474

13376 Comber Way

Surrey BC V3W 5V9

[email protected]

www.ortechindustries.com

375 Admiral Blvd

Mississauga, ON L5T 2N1

CAUTION

Application Notice

1. All electrical connections must be in accordance with local codes, ordinances and the National Electric code

2. DO NOT mount in hazardous locations, or near gas or electric heaters

3. DO NOT let power cords touch hot surface

4. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel

5. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition

6. DO NOT use LED Exit Signs for other than intended use

7. Allow battery to charge for 24 hours before first use

INSTALLATION GUIDE

AC Wiring

1. Connect the WHITE wire to NEUTRAL

2. If using 120V, connect the BLACK wire to the hot lead

3. If using 347V, connect the RED wire to the hot lead

4. Cap the unused lead

LED Strip

LED/SW

JK2 RH1

LAMP

2LAMP1

MAIN

PCBA

TRAN

Batt2

Batt1

AC Input

Red 347V AC

Black 120V AC

White NEUTRAL

2nd Battery

1st Battery

Assembly Lamp Heads

1. Open front cover by flat screwdriver

2. Insert the lamp heads at the corners of main frame.

Select direction of lamp head before inserting

3. Connect male connector on lamp head to female

connector on PCBA

Connect lamp heads

connector on PCBA

Lamp head (forward) Lamp head (backward)

Wiring Diagram

INSTALLATION GUIDE

LED Exit Signs

MODEL OE-316

Mounting Instruction

The fixture is suitable for wall mounting, side mounting, ceiling mounting.

1. Open front cover and assemble 2 pcs lamp heads on the frame

2. Knockout appropriate mount screw hole and cable hole, mount back

plate on the wall after feed building AC supply cable in to back plate

(see Fig.1 below)

3. For ceiling and side mounting purpose, remove the mounting hole

cover on the top or side of the unit, assemble the canopy

(see Fig.2,3,4 below)

4. Attach crossbar to junction box, set the longer blade of crossbar

touching the J-Box

5. Route the proper wires through mounting hole out of housing

6. Make electrical connections inside the J-Box like the wiring diagram on

page 1 of this instruction manual

7. Push excess wire into J-Box, use screws to tighten canopy to crossbar so

that copy is securely fastened and tight against the wall

8. Attach battery connector to PC board, restore front cover on unit, adjust

position of lamp heads as needed

9. If pictogram direction is assembled not suitable, pictogram can take out

for change direction or replace pictogram, and then insert into the

diffuser easily (see Fig.5 below)

Instruction Manual

1-888-543-6473

1-888-541-6474

13376 Comber Way

Surrey BC V3W 5V9

[email protected]

www.ortechindustries.com

375 Admiral Blvd

Mississauga, ON L5T 2N1

Wall Mounting

Fig.1

Battery

Connector J-Box

Side Mounting

Fig.2

Canopy

Crossbar

J-Box

Ceiling Mounting

Fig.3

J-Box

Crossbar

Canopy

Canopy Assembly

Fig.4

Insert canopy into housing at 20° and twist.

Quick snap is now locked firmly.

CAUTION: Trying to remove when canopy is locked in

place may cause damage.

Change Direction of the Pictogram

Fig.5Pictogram

Table of contents

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions