Orion 5Q740 User manual
USER’S MANUAL
MODEL No.: 5Q740
BEFORE USING THIS COLOR MONITOR,
READ AND OBSERVE ALL OF THIS USER’S MANUAL
1
CONTENTS
SAFETY INSTRUCTION 2
CAUTIONS 4
FCC RF INTERFERENCE STATEMENT 5
INSTALLATION 6
RESOLUTION 7
CONTROLS AND FUNCTIONS 8
REAR VIEW 13
SPECIFICATIONS 14
TROUBLE SHOOTING GUIDE 15
ThisMonitorwas
ManufacturedbyISO9001
CertifiedFactory
SAFETY INSTRUCTION
1.Read all of these instructions.
2.Save these instructions for later use.
3.Follow all warnings and instructions marked on the product.
4.Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
5.Do not use this product near water.
6.Do not place this product on an unstable cart, stand or table.
The product may fall, causing serious damage to the product.
7.Slots and openings in the cabinet and the back or bottom are provided for
ventilation: to ensure reliable operation of the product and to protect it from
overheating these openings must not be blocked by placing the product on a bed,
sofa, rug or other similar surface. This product should never be placed near or over
a heat register.
This product should not be placed in a built-in installation unless proper ventilation
is provided.
8.This product should be operated from the type of power source indicated on the
marking label. If you are not sure of the type of power available consult your dealer
or local power company.
9.This product is equipped with a 3 wire grounding type plug having a third(grounding)
pin. This is a safety feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not defeat the purpose of
the grounding-type plug.
10.Do not allow anything to rest on the power cord.
Do not locate this product where persons will walk on the cord.
11.If an extension cord is used with this product, make sure that the total of the
ampere ratings on the products plugged into the extension cord do not exceed the
extension cord ampere rating. Also, make sure that the total of all products
plugged into the wall outlet does not exceed 10 amperes.
12.Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a risk of fire
or electric shock. Never spill any kind of liquid on the product.
3¶INSTRUCTIONMANUAL
SAFETY INSTRUCTION
13. Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks.
Refer all servicing to service personnel.
14. Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the Product does not operate normally when the operating instructions are
followed. Adjust only those controls that are covered by the operating
instructions since improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore normal
operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating a need for
service.
CCAAUUTTIIOONN
The power supply cord is used as the main disconnect device, ensure that the
socket-outlet is located/installed near the equipment and is easily accessible.
AATTTTEENNTTIIOONN
Le cordon d`alimentation est utillsé comme interrupteur général. La prise de
courant doit être située ou installée à proximité du matériel et être facile
d`accès
CAUTION TO SERVICE PERSONNEL
POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN
THIS PRODUCT. UNPLUG THIS PRODUCT FROM THE WALL OUTLET
BEFORE REMOVING THE BACK COVER AND SERVICING
EMISSION CHARACTERISTICS TESTED BY SEMKO
THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH
THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990.10.(MPR•±)
4
CAUTIONS
Removal of the back cover should be carried out only by qualified personnel.
This display monitor contains high voltage inside.
To prevent shock or fire hazard. Do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to
vibrations, dust of corrosive gases.
Ventilation holes are provided on the cabinet to prevent the temperature from
rising.
Do not cover the unit or place anything on the top of unit. Ventilation holes are
provided also on the bottom of the cabinet.
Avoid placing the unit in direct sunshine or near a heating appliance.
Do not place a magnet, speaker system, floppy disc drive or anything which will
generate magnetism near the unit, A magnetic field may cause blurred colors or
distortion of the displayed pattern.
Do not use the unit against a bright back ground and where sunlight or other light
sources will shine directly on the monitor.
Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.
5
FCC RF
INTERFERENCE STATEMENT
NNOOTTEE::
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not
expressly approved by the grantee or manufacturer could void the users
authority to operate such equipment.
¢∫DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the radio interference regulation of Canadian
Department of Communications.
¢∫AVIS DE CONFORMATION AU MDC(DOC)
Le présent appareil numérique n´émet pas de bruits radio-électriques dépassant les
limites appliqués aux appareils numériques de Class B d´après les règlements sur
le brouillage radio-électrique conçuent par le ministère des communications du
Canada.
¶ 6
INSTALLATION
NO TOOLS ARE REQUIRED TO INSTALL THE MONITOR.
SIMPLY FOLLOW THE INSTRUCTIONS OUTLINED IN THE
FOLLOWING PAGE.
1. INSTALLING THE TILT/SWIVEL STAND
1) Align the stand with the slots in the bottom of the monitor and insert the
Tilt/Swivel Stand into the slots.
2) Push the Tilt/Swivel Stand firmly toward the front of the monitor until the latches
click into the locked position.
2. CONNECT THE SIGNAL CABLE
1) Connect the end into the graphic card on back of the computer.
2) Secure the connection with the screws on the plug.
3. CONNECT THE POWER CORD
Connect the female end of the power cord to the power input
receptacle on the back panel of the monitor.
Then, plug the male end of the power cord to an AC outlet or computer.
4. TURN THIS MONITOR ON AND START YOUR SYSTEM
HOOK
b
1
22
a
Resolution Horizontal Vertical Clock Poles
Frequency(KHz) Frequency(Hz) Frequency(MHz) (H / V)
IBM(640 * 350)
IBM(720 * 400)
IBM(640 * 480)
VESA(640 * 480)
VESA(800 * 600)
VESA(800 * 600)
VESA(800 * 600)
VESA(1024 * 768)
VESA(1024 * 768)
VESA(1280 * 1024)
31.469
31.469
31.469
43.269
37.879
46.875
53.674
48.363
68.677
63.981
70.087
70.087
59.941
85.008
60.317
75.000
85.061
60.004
84.997
60.020
25.175
28.322
25.175
36.000
40.000
49.500
56.256
65.000
94.500
108.000
(+ / -)
(- / +)
(- / -)
(- / -)
(+ / +)
(+ / +)
(+ / +)
(- / -)
(+ / +)
(+ / +)
7
RESOLUTION
It has 10 user setting modes which you can store except for factory setting mode.
Displayingusermodeexcept for factorysetting modes, pleaseadjust themonitor
screen for yourself.
After that, the screen data is stored to the memory within microprocessor.
2. THE WAY OF ADJUSTMENT
When you want to adjust the screen, please refer to function of controls.
Those screen data are automatically stored to the memory within microprocessor.
1. RECOMMENDED SIGNAL TIMING CHART
¶8
CONTROLS AND FUNCTIONS
A. POWER SWITCH( )
Turns the power ON or OFF. There will be a few seconds delay before
the display appears.
The power LED(next to the power switch) lights when the power
is turned ON.
The power is turned off by pressing the power switch again and
the power LED goes out.
B. DEGAUSS BUTTON
If the CRT of the monitor becomes magnetized, Picture color is not clean and
may be in different light and darkness.
If you push the DEGAUSS botton when OSDmenu is not shown, you can get
the clean picture and uniformity color.
But, if you push the DEGAUSS button when OSD menu is shown, you make
OSD menu disappeared.
In addition, you can use this button to return to the previous menu after adjustment.
NOTE
- The CRT is degaussed automatically each time the monitor is turned on.
- When the button is pushed, the picture will be oscillate for a few seconds.
- Pressing more than once has on effect.
If you want to demagnetize again, push after at least 30 minutes.
C.SELECT BUTTON
POWER INDICATOR(LED)
A. POWER SWITCH
D. ADJUST BUTTONS
(DOWN & UP)
B.DEGAUSS BUTTON
9¶INSTRUCTIONMANUAL
CONTROLS AND FUNCTIONS
You can use the UP or DOWN button to make selection for each function.
If you push this SELECT button once more, this allows you to activate the desired
adjustment with the change of adjustment bar color black to violet.
C. SELECT BUTTON
If you want to adjust to the monitor, push the SELECT button.
If you push the button, one of the following two OSD menu is displayed for
control on screen.
Table of contents
Other Orion Monitor manuals
Orion
Orion LCD Monitor User manual
Orion
Orion F9S936 User manual
Orion
Orion ORL1850W User manual
Orion
Orion OPM-4250 User manual
Orion
Orion OLMU-5520 User manual
Orion
Orion F9S946 User manual
Orion
Orion OLS-32 User manual
Orion
Orion OLS-3201PGB User manual
Orion
Orion VALUE SERIES User manual
Orion
Orion 9REDP User manual
Orion
Orion VALUE SERIES User manual
Orion
Orion 17" TFT-LCD MONITOR User manual
Orion
Orion OPM-4260 User manual
Orion
Orion 215LEDP User manual
Orion
Orion MIS-4220 User manual
Orion
Orion LB2000 User manual
Orion
Orion PK-8420 User manual
Orion
Orion PREMIUM SERIES User manual
Orion
Orion 9S946 User manual
Orion
Orion 26RTV User manual
