Orbit OBE165AF User manual
OBE165AF
Elliptical Cross Trainer
Owner’s Manual
Table of Contents
Product Safety Page.01.............................................................................
Trouble Shooting & Maintenance ...................................... Page.11
Assembly ............................................................................. Page.04 ~ 09
Hardware & Tools ...................................................................... Page.03
Computer ....................................................................................... Page.12
Part List .......................................................................................... Page.21
Exploded View ............................................................................ Page.22
Part Drawing & Box A/B Contents ....................................... Page.02
Adjustments ................................................................................ Page.10
Warm Up ....................................................................................... Page.20
Product Safety
Basic precautions should always be followed, including the following safety instructions
when using this equipment: Read all instructions before using this equipment.
1. Read all the instructions in this manual and do warm up exercises before using this equipment.
2. Before exercise, in order to avoid injuring your muscles, warm-up exercise for every muscle
group is highly recommended. Please refer to the Warm Up pages for pre and post workout.
3. Please make sure all components are not damaged and in working order before use. This
equipment should be placed on a flat surface while in use. Using a mat or other material on
the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that
might catch in any part of the equipment.
5. Do not attempt any maintenance or adjustments other than those described in this manual.
Should any problems arise, discontinue use and consult an Authorized Service Representative.
6. Be careful when stepping on or leaving the pedals. Always hold the handlebars first and make
sure the pedal at your side is at its lowest position. Step on the pedal, and stride over the main
frame then step on the other pedal. When using, please hold onto the handlebars. To ensure
the pedals run smoothly push or pull on the handlebars first, then follow with leg motion.
When stepping off the machine, make sure one pedal is at its lowest position and step out of
there before stepping out of the pedal at the highest position.
7. Do not use the equipment outdoors.
8. This equipment is for household use only.
9. Only one person should be on the equipment while in use.
10. Keep children and pets away from the product while in use. This machine is designed for
adults only. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop
exercising immediately and consult your physician before continuing.
11. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising
immediately and consult your physician before continuing.
12. The maximum weight capacity for this product is 300 lbs/135 kgs.
Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years
old or who have pre-existing health problems. Read all instructions
before using any fitness equipment.
WARNING:
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.
1
2
Part Drawing & Box A/B Contents
A01 A12 A16 A15
C12/C28
MainBody U Shape Rail Front Stabilizer Hand Pulse Handlebar
Foot Pedal
1PC 1PC 1PC 1PC
1Set Computer
Handrail Arm
Decorative Cover
Front Post
Decorative Cover
Water Bottle
1PC 2Set 1Set
1PC
D02 C17/C18 C07/C08
C35
A02 A03/A05/A07 A04/A06/A08 A13/A14
C11
Front Post Left Foot Bar Set Right Foot Bar Set Handrails
Nut Cap
1PC 1Set 1Set 1Set
6PCs Water Bottle Holder Webbing AC Adaptor
Lubricant
1PC 2PCs 1PC
1PC
C27 C33 D08
Box B
Box A
Foot Pedal Plug 8PCs
C27
3
Hardware & Tools
B32 (9) B33 (1) B21 (6) B40 (10)
B28 (5)
Hexagon Head Bolt
M8x16mm Washer 5/16”x20x2.0t Bolt M5x16mm Bolt M8x25mm4PCs 4PCs 10PCs 2PCs
Bolt M8x50mm 4PCs
B29 (12) B30 (3) B23 (4)
Nut M8 Bolt M6x15mm4PCs 8PCs
Curve Washer
M8x20x1.5t 4PCs
Bolt 3/8”x64mm 2PCs Washer 3/8”x20x2.0t 4PCs Cap Nut 3/8” 2PCs
Hex Tool With
Phillips Screwdriver
(13mm/14mm) 1PC Allen Wrench (M5) 1PC Allen Wrench (M4) 1PC
B41 (11) B42 (2) B43 (7)
(8) (14) (13)
7
Assembly
7. Left and Right Handrails Installation
8. Hand Pulse Handlebar Installation
(a) Insert the Sensor Wire I (D04) from the Front
Post (A02) into the hole on the Hand Pulse
Handlebar (A15) and then pull it out from the
Hand Pulse Handlebar (A15).
(b) Attach the Hand Pulse Handlebar (A15) onto
the Front Post (A02) with Two M8x25mm Bolts
(B40). Tighten bolts with the M5 Allen Wrench
provided.
9. Left/Right Front Post Decorative Covers Installation
(a) Attach the Left/Right Front Post Decorative Covers
(C07, C08) onto the Front Post (A02) with Two
M5x16mm Bolts (B21). Tighten bolts with the Hex
Tool with Phillips Screwdriver provided.
(a) Attach the Left/Right Handrails (A13, A14) into the
Left/Right Handrail Arms (A03, A04) with Four
M8x50mm Bolts (B28), Four M8 Nylon Nuts (B29),
and Four 8x20x1.5T Curve Washers (B30).
Tighten nylon nuts with the Hex Tool with Phillips
Screwdriver provided.
A13
A14
B28
B28 B28
B28
B30
B30
B30
B30
B29
B29
B29
B29
A04
A03
A15
A02
B40 B40
D10
D04
C07
C08
B21
B21
A02
C01
C02
Hex Tool With Phillips Screwdriver (13mm/14mm)
(B28)Bolt M8x50mm---4PCs
(B29)Nut M8---4PCs
(B30)Curve Washer M8x20x1.5t---4PCs
Allen Wrench
Hex Tool With Phillips Screwdriver (13mm/14mm)
(B21)Bolt M5x16mm---2PCs
(B40)Bolt M8x25mm---2PCs
8
Assembly
10. Handrail Arm Decorative Covers-Right/Left Installation
11. Foot Pedal Installation
(a) Align the Right Foot Pedal and Left Foot Pedal (C12, C28)
and fit to Right Foot Bar and Left Foot Bar (A05, A06).
Secure and tighten firmly with Four M6x15mm Bolts (B23).
(b) Slide the Foot Pedal Plug(C36) into the bolt holes
of the foot pedal(C12/C28).
Tighten bolts with the M4 Allen Wrench provided.
12. Bottle Holder Installation
(a) Remove two M5x12mm Bolts (B15) from the Front Post (A02).
Remove bolts with the M4 Allen Wrench provided.
Attach the Bottle Holder (C27) onto the Front Post (A02) with
Two M5x12mm Bolts (B15) that were removed.
Tighten bolts with the M4 Allen Wrench provided.
(a) Attach the Handrail Arm Decorative Cover-Right (C18) and
Handrail Arm Decorative Cover-Left (C17) onto the Left
Handrail Arm (A03) with Four M5x16mm Bolts (B21).
Tighten bolts with the Hex Tool with Phillips Screwdriver
provided.
(b) Attach the Handrail Arm Decorative Cover-Right (C18) and
Handrail Arm Decorative Cover-Left (C17) onto the Right
Handrail Arm (A04) with Four M5x16mm Bolts (B21).
Tighten bolts with the Hex Tool with Phillips Screwdriver
provided.
C17
C18
C18
C17
B21
B21
B21
B21
B21
B21
B21 B21
A14
A13
A04
A03
C27
B15
B15
A02
Hex Tool With Phillips Screwdriver (13mm/14mm)
(B21)Bolt M5x16mm---8PCs
Allen Wrench
(B23)Bolt M6x15mm---4PCs
Allen Wrench
B23 B23
B23
B23
C28
C12
A05
A06
C36
C36
C36
C36
Other manuals for OBE165AF
1
Table of contents
Other Orbit Elliptical Trainer manuals
Popular Elliptical Trainer manuals by other brands
Bonn Germany
Bonn Germany Concept 2.2 user manual
Precor
Precor Resolute RSL 620 Assembly guide
NordicTrack
NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS
Vision Fitness
Vision Fitness X6600iNetTV Assembly guide
Matrix
Matrix MX-A5x owner's manual
SportsArt Fitness
SportsArt Fitness ECO-NATURAL Elite E874 owner's manual
