Optoma X401 User manual

SERVICE MANUAL

Prepared: Check: Approved:

Date Revise Version Description

2013.2.4 V1.0 Initial Issue

2013.7.29 V2.0

Change service mode:power,left,left,menuto power,

up,right,up,left,menu (P14,P24,P27,P33)

X401/W401

Mina Amy

Condential

X401/W401

Preface

This manual is applied to X401/W401 projection system.The manual gives you a

brief description of basic technical information to help in service and maintain the product.

Your customers will appreciate the quick response time when you immediately identify

problems that occur with our products. We expect your customers will appreciate the

service that you offer them.

This manual is for technicians and people who have an electronic background. Please

send the product back to the distributor for repairing and do not attempt to do anything

that is complex or not mentioned in the troubleshooting.

Notice:

The information found in this manual is subject to change without prior notice. Any

subsequent changes made to the data herein will be incorporated in future edition.

X401/W401 Service Manual

Manual Version Rev 2.0

X401/W401 Condential

X401/W401 Comparison List

Parts W401 X401

ROD Module 70.8LM15GR01 70.8JS24GR01

DMD 48.8EJ01G003 48.8CQ01G005

Main BD 80.8TC01G011 80.8TE01G011

Engine Module 70.8TC08GR01 70.8TE19GR01

IO COVER 70.8TC09GR01 70.8TE18GR01

Condential

X401/W401

Table of Content

Chapter 1 Introduction

Highlight 1-1

Chapter 2 Disassembly Process

Equipment Needed & Product Overview 2-1

Repair notice 2-2

Rod Adjustment 2-5

Re-write Lamp Usage Hours 2-6

Repair Action 2-7

Chapter 3 Troubleshooting

LED Lighting Message For Projector 3-1

Main Procedure 3-2

Pin Assignment 3-3

Chapter 4 Function Test & Alignment Procedure

Test Equipment Needed 4-1

Test Condition 4-1

I/O Port Test 4-2

Run In Test 4-9

Test Inspection Procedure 4-9

Auto Waveform and Factory Fan RPM 4-10

ADC Calibration 4-11

RJ45 Port Test 4-12

III

X401/W401 Condential

Chapter 5 Firmware Upgrade

Section 1: System Firmware Upgrade 5-1

Equipment Needed 5-1

Get into FW mode 5-2

Check FW version 5-2

Section 2: MCU FW Upgrade Procedure 5-3

Equipment Needed 5-3

Setup Procedure 5-4

Upgrade Procedure 5-6

Network FW Upgrade Procedure 5-8

Equipment Needed 5-8

Write Down Projector IP 5-9

PC Hardware Link 5-11

Chapter 6 EDID Upgrade

EDID Upgrade Procedure 6-1

Appendix A Exploded Image I

Appendix B

Serial Number Denition I

PCBA Code Denition II

X401/W401 Condential 1-1

Chapter 1

Introduction

1-1 Highlight

No Item Description

1Dimensions (WxDxH) ● 324x234x112mm (with feet)

● 324x234x97mm (w/o feet)

2 Power Supply ● Universal AC 100V-240V±10%, 50-60Hz

3 Power Consumption

● Bright (Normal): TYP 347W MAX 382W @110VAC

TYP 335W MAX 369W @220VAC

● ECO:TYP 294W MAX 323W@110VAC

TYP 285W MAX 314W@220VAC

4Keystone correction ● +/-40 degree

5 Throw ratio ● 1.6~1.92 (D/W) (For X401)

● 1.28~1.536 (D/W) (For W401)

6 Projection lens ● YM25

7 Lamp life

Bright Mode:

● 3000Hours Standard @280W, 50% Survival Rate

ECO Mode:

● 4000 Hours Typical @230W, 50% Survival Rate

8 Lamp ● 280W Lamp (Osram E20.8)

9DMD Chip&Number of

active dots

● 0.55” XGA, S450, Dark Chip 3 (For X401)

● 0.65” WXGA, S450, Dark Chip 3(For W401)

● Number of active dots: 1024x768 (For X401)

1280x800 (For W401)

10 Color wheel ● 6 segments (R78Y44G81C34W55B68)

11 System controller ● TI DDP 4421

12 Video compatibility

● NTSC: M/J,3.58MHz,4.43MHz

● PAL: B, D, G, H, I, M, N,4.43MHz

● SECAM: B, D, G, K, K1, L,4.25/4.4MHz

● SDTV: 480i/p, 576i/p,

● HDTV: 720p(50/60Hz), 1080i(50/60Hz),1080p(50/60Hz)

Condential 1-2

X401/W401

No Item Description

13 Input signal spec

● VGA-in: VGA in 1 (wireless dongle, YPbPr)

VGA in 2 (HDTV, YPbPr)

● Video x 1

● Audio-in (Green coded port):

• Audio-in 1, 2, 3 (Daughter Board)

• Mini Jack x 3

● HDMI: HDMI v1.4

● Audio-in connectivity grouping

• VGA-in1 -> Audio in1

• VGA-in2 -> Audio in2

• Video -> Audio in3

14 Altitude&Temperature

● Operating: 0~2,500 ft 5°C~40°C

2,500~5,000 ft 5°C~35°C

5,000~10,000 ft 5°C~30°C

1-2 Compatible Mode

Computer Compatibility (Analog)

Compatibility Resolution Refresh Rate (Hz) Analog HDMI

NTSC 720 x 480 60 - -

PAL/SECAM 720 x 576 50 - -

VGA 640 x 480 60 O O

640 x 480 67 O-

640 x 480 72.8 O-

640 x 480 85 O-

SVGA 800 x 600 56.3 O-

800 x 600 60.3 O O

800 x 600 72.2 O O

800 x 600 85.1 O O

800 x 600 120 O O

XGA 1024 x 768 60 O O

1024 x 768 70.1 O O

1024 x 768 75 O O

1024 x 768 85 O O

1024 x 768 120 O O

Condential 1-3

X401/W401

Note: If the Computer Compatibility supportive signal is different from User's Manual, please refer

to User's Manual.

Compatibility Resolution Refresh Rate (Hz) Analog HDMI

WSVGA 1024 x 600 60 -O

HDTV (720p) 1280 x 720 50 O O

1280 x 720 60 O O

1280 x 720 120 O O

WXGA 1280 x 768 60 O O

1280 x 768 75 O O

1280 x 768 85 O O

1280 x 800 60 O O

1366 x 768 60 O O

WXGA+ 1440 x 900 60 O O

SXGA 1280 x 1024 60 O O

1280 x 1024 75 O O

1280 x 1024 85 O O

SXGA+ 1400 x 1050 60 O O

UXGA 1600 x1200 60 O O

HDTV (1080p) 1920 x 1080 24 O O

1920 x 1080 30 -O

1920 x 1080 50 O O

1920 x 1080 60 O O

HDTV (1080i) 1920 x 1080 50 -O

1920 x 1080 60 -O

WUXGA 1920 x 1200 60 O O

SDTV (576i) 768 x 576 50 -O

SDTV (576p) 768 x 576 50 -O

SDTV (480i) 640 x 480 60 -O

SDTV (480p) 640 x 480 60 -O

X401/W401 Condential 2-1

Chapter 2

Disassembly Process

2-1 Equipment Needed & Product Overview

1. Screw Bit (+): 105

2. Screw Bit (+): 107

3. Screw Bit (-): 107

4. Hex Sleeves: 5 mm

5. Tweezers

6. Projector

* Before you start: This process is protective level II. Operators should wear electrostatic chains.

* Note: - If you need to replace the main board, you have to record the lamp usage hour.

- Some related contents please refer to common SM chapter 2.

X401/W401 Condential 2-2

2-2 Repair notice

Item Male Connector

on Main Board The key feature Figure

A & I Speaker

Compose of Red/

Black Wire and Black

wire tube (2 pin)

B Lamp Driver Black wire tube (5

pin)

CSystem Fan Compose of Red/Yel-

low/Black Wire (3 pin)

D Blower

Compose of Black/

Yellow/Red Wire and

Blue wire tube (3 pin)

EPhoto Sensor

Compose of Red/

Black/White Wire and

Black wire tube (3

pin)

FIR

Compose of Black/

Yellow/Red Wire and

Gray wire tube (3 pin)

2-2-1 Disassemble Main

Board

Please refer to the below table details of

each connector on Main Board.

G F D A

EHI B

Other manuals for X401

This manual suits for next models

Table of contents

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB operating instructions

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

InFocus

InFocus LitePro 560 user guide

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual