Optoma X306ST User manual
1English
Table of Contents ............................1
Usage Notice...................................2
Safety Information...............................2
Precautions.........................................3
Eye Safety Warnings ..........................5
Product Features ................................5
Introduction......................................6
Package Overview..............................6
Product Overview ...............................7
Main Unit.............................................. 7
Control Panel ....................................... 8
Input/Output Connections .................... 9
Remote Control.................................. 11
Installation .....................................12
Connecting the Projector ..................12
Connect to Computer/Notebook ........ 12
Connect to Video Sources ................. 14
Powering the projector On / Off ........16
Powering On the Projector................. 16
Powering Off the Projector................. 17
Warning Indicator............................... 17
Adjusting the Projected Image..........18
Adjusting the Projector’s Height ........ 18
Adjusting the Projector’s Focus ......... 19
Adjusting Projection Image Size ........ 19
User Controls ................................21
Control Panel & Remote Control ......21
Control Panel ..................................... 21
Remote Control.................................. 22
On-screen Display Menus ................27
How to operate ................................. 27
Menu Tree.......................................... 28
IMAGE ............................................... 30
IMAGE | Advanced ............................ 32
IMAGE | Advanced | Signal (RGB) ... 34
DISPLAY............................................ 35
DISPLAY | 3D ................................... 38
SETUP............................................... 39
SETUP | Security ............................... 41
SETUP | Audio Settings..................... 43
SETUP | Advanced ............................ 44
SETUP | LAN ..................................... 45
OPTIONS........................................... 50
OPTIONS | Advanced........................ 52
OPTIONS | Lamp Settings................. 53
OPTIONS | Optional Filter Settings ... 54
Appendices....................................55
Troubleshooting ................................55
Replacing the lamp ...........................60
Compatibility Modes .........................62
Computer/Video/HDMI/Mac
Compatibility ...................................... 62
3D Input Video Compatibility ............. 63
RS232 Commands and Protocol
Function List .....................................64
RS232 Pin Assignments .................... 64
RS232 Protocol Function List ............ 65
Wall Mount Installation......................69
Optoma Global Ofces .....................70
Regulation & Safety Notices .............72
Table of Contents
2
English
Usage Notice
Safety Information
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Important Safety Instruction
1. Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air ow.
2. Do not use the projector near water or moisture. To reduce the risk
of re and/or electric shock, do not expose the projector to rain or
moisture.
3. Do not install near heat sources such as radiators, heaters, stoves or
any other apparatus such as ampliers that emits heat.
4. Clean only with dry cloth.
5. Only use attachments/accessories specied by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
Unit has been dropped.
Power supply cord or plug has been damaged.
Liquid has been spilled on to the projector.
Projector has been exposed to rain or moisture.
Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
Optoma before you send the unit for repair.
7. Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in re or
electric shock.
8. See projector enclosure for safety related markings.
9. The unit should only be repaired by appropriate service personnel.
3English
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀■Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt and damage your eyes.
▀■Warning- To reduce the risk of re or electric shock, do not
expose this projector to rain or moisture.
▀■Warning- Please do not open or disassemble the projector as
this may cause electric shock.
▀■Warning- When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
60-61.
▀■Warning- This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀■Warning- Reset the “Lamp Reset” function from the on-screen
display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 53).
▀■Warning- When switching the projector off, please ensure
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀■Warning- Do not use lens cap when projector is in operation.
▀■Warning- When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
▀■Warning- Do not look into or point the laser pointer on your
remote control into your or someone’s eyes. Laser
pointer can cause permanent damage to eyesight.
When the lamp
reaches the end
of its life, the pro-
jector will not turn
back on until the
lamp module has
been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 60-61.
4
English
Usage Notice
Do:
Turn off and unplug the power plug from the AC outlet before
cleaning the product.
Use a soft dry cloth with mild detergent to clean the display
housing.
Disconnect the power plug from AC outlet if the product is
not being used for a long period of time.
Do not:
Block the slots and openings on the unit provided for
ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
- In extremely hot, cold or humid environments.
Ensure that the ambient room temperature is within
5 - 40°C.
Relative Humidity is 5 - 40°C, 80% (Max.),
non-condensing.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic eld.
- In direct sunlight.
5English
Usage Notice
Eye Safety Warnings
▀■Avoid staring/facing directly into the projector beam at all
times. Keep your back to the beam as much as possible.
▀■When projector is used in a classroom, adequately supervise
students when they are asked to point out something on the
screen.
▀■In order to minimize the lamp power, use room blinds to
reduce ambient light levels.
Product Features
▀■XGA (1024x768) / WXGA (1280x800) Native resolution
▀■HD compatible – 720p and 1080p supported
▀■VGA monitor loop through
(works in standby mode > 0.5W)
▀■BrilliantColorTM Technology
▀■Security Bar and Kensington Lock
▀■RS232 control
▀■Rapid shutdown
▀■Built-in speakers
▀■Network support
▀■Full 3D
▀■Eco+ and Quick Resume
Monitor loop
through only sup-
ported in VGA1-
In/YPbPr.
6
English
Introduction
Documentation :
User’s Manual
Warranty Card
Quick Start Card
WEEE Card
(for EMEA only)
STOP Card
(for US Only)
Due to different
applications in
each Country,
some regions
may have
different
accessories.
Power Cord
IR Remote Control
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
2 × AAA Batteries
Projector with lens cap VGA Cable
Menu
7English
Introduction
Product Overview
Main Unit
Control Panel1.
Focus Ring2.
Speaker3.
Zoom Lens4.
IR Receiver5.
Input / Output Connections6.
Power Socket7.
Ventilation (inlet)8.
Ventilation (outlet)9.
The interface
is subject to
model’s speci-
cations.
Do not block
projector in/out
air vents.
3
7
6
8
4
5
2
8
9
1
8
English
Introduction
/
/
Control Panel
2 31
7
Power LED1.
Lamp LED 2.
Temp LED3.
Enter / Help4.
Menu5.
Re-Sync6.
Keystone Correction7.
Four Directional Select Keys8.
Source9.
Power/Standby button10.
510
69
8
4
9English
Introduction
HDMI
VGA-OUT RS-232C
VGA2-IN/YPbPr
VIDEO S-VIDEO
AUDIO-IN
AUDIO-OUT
MOUSE
(SERVICE)
VGA1-IN/YPbPr/
5421 3 86 7
10
Input/Output Connections
Monitor loop
through only sup-
ported in VGA1-
IN/YPbPr.
USB Connector / Type-B (Connect to PC for Remote Mouse 1.
function)
HDMI Connector2.
Composite Video Input Connector3.
S-Video Input Connector4.
VGA-Out Connector (Monitor Loop-through Output)5.
VGA1-In/YPbPr/6. Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPrr/
Wireless function via VGA Dongle)
RS-232 Connector (9-pin DIN Type)7.
Audio Input connector (3.5mm mini jack)8.
Power Socket9.
VGA2-In/YPbPr Connector 10.
(PC Analog Signal/Component Video Input/HDTV/YPbPr)
Kensington11. TM Lock Port
Audio Output Connector (3.5mm Mini Jack)12.
Type A
9 1211
10
English
Introduction
RJ-45
MOUSE
(SERVICE)
HDMI
VGA-OUT
RS-232C VGA2-IN/YPbPr
VGA1-IN/YPbPr/ VIDEO AUDIO1-IN
(VGA1/VGA2)
AUDIO2-IN
(VIDEO)
AUDIO-OUT
MIC
431 2 85 7
11
Monitor loop
through only sup-
ported in VGA1-
IN/YPbPr.
RJ-45 Networking Connector1.
USB Connector / Type-B (Connect to PC for Remote Mouse 2.
function)
HDMI Connector3.
VGA-Out Connector (Monitor Loop-through Output)4.
VGA1-In/YPbPr/5. Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPrr/
Wireless function via VGA Dongle)
Composite Video Input Connector6.
Audio 1 Input connector (3.5mm mini jack)7.
(for VGA1/VGA2)
Audio 2 Input connector (3.5mm mini jack)8.
(for Video)
Power Socket9.
RS-232 Connector (9-pin DIN Type)10.
VGA2-In/YPbPr Connector 11.
(PC Analog Signal/Component Video Input/HDTV/YPbPr)
Kensington12. TM Lock Port
Microphone Input Connector13.
Audio Output Connector (3.5mm Mini Jack)14.
Type B
9 1312
6
10 14
Other manuals for X306ST
3
This manual suits for next models
1
Table of contents
Other Optoma Projector manuals
Optoma
Optoma DS216 User manual
Optoma
Optoma TW635-3D User manual
Optoma
Optoma W307USTi User manual
Optoma
Optoma UHL55 User manual
Optoma
Optoma HD200X User manual
Optoma
Optoma HD66 User manual
Optoma
Optoma DX346 User manual
Optoma
Optoma DS325 User manual
Optoma
Optoma EzPro 710 User manual
Optoma
Optoma S341-M User manual
