Optoma HD25 User manual

SERVICE MANUAL

TSE: Mina Check: Amy Approved: Alick

Date Revise Version Description

2012.12.17 V1.0 Initial Issue

2013.05.20 V2.0 Add HD25e

2013.07.25

V3.0

HD25/HD25LV

Change service mode:power,left,left meun to power,up,

right,up,left,menu (P17,P27,P31,P33)

HD25/HD25LV/HD25e

Condential

HD25/HD25LV/HD25e I

Preface

This manual is applied to HD25/HD25LV/HD25e projection system. The manual gives

you a brief description of basic technical information to help in service and maintain the

product.

Your customers will appreciate the quick response time when you immediately identify

problems that occur with our products. We expect your customers will appreciate the

service that you offer them.

This manual is for technicians and people who have an electronic background.Please

send the product back to the distributor for repairing and do not attempt to do anything

that is complex or is not mentioned in the troubleshooting.

Notice: The information found in this manual is subject to change without prior notice.

Any subsequent changes made to the data herein will be incorporated in future

edition.

HD25/HD25LV/HD25e Service Manual

Manual Version 2.0

Condential

HD25/HD25LV/HD25e

HD25/HD25LV/HD25e Comparison ListComparison List

Parts HD25 HD25LV HD25e

Main Board 80.8RV01G002 80.8RU01G002 80.8VC01G001

ROD 70.8EG32GR01 70.8RU25GR01

Lamp Module SP.8RU01GC01 SP.8VC01GC01

Engine Module 70.8RV12GR01 70.8RV09GR01 70.8VC19GR01

Color Wheel 70.8RV10GR01 70.8RU24GR01

Condential

HD25/HD25LV/HD25e III

Table of Content

Chapter 1 Introduction

Highlight 1-1

Compatible Mode 1-2

Chapter 2 Disassembly Process

Equipment Needed & Product Overview 2-1

Disassemble Top Cover Module 2-2

Disassemble Main board 2-2

Disassemble Lens 2-5

ROD Adjustment 2-6

Re-write Lamp Hours 2-7

Repair Action 2-8

Chapter 3 Troubleshooting

LED Lighting Message 3-1

Main Procedure 3-2

Pin Assignment 3-3

Chapter 4 Function Test & Alignment Procedure

Test Equipment Needed 4-1

Test Condition 4-1

VGA Port Test 4-2

Audio port Test 4-7

Video port Test 4-7

Component port Test 4-7

HDMI Port Test 4-8

3D Test 4-8

Condential

HD25/HD25LV/HD25e IV

Run In Test 4-8

Test Inspection procedure 4-9

Auto Waveform and Factory Fan RPM 4-10

Chapter 5 Firmware Upgrade

Section 1: System Firmware Upgrade 5-1

Section 2: 8051 Firmware Upgrade Procedure 5-3

Appendix A

Exploded Image I

Appendix B

   SerialNumberSystemDenition     I

   PCBACodeDenition      II 

HD25/HD25LV/HD25e Condential 1-1

Chapter 1

Introduction

1-1 Highlight

No Item Description

1Dimensions (WxDxH) ● 324x234x97mm(WxDxH) (w/o feet)

● 324x234x112mm (WxDxH) (with feet)

2Power Supply ● Auto-ranging: 100V ~ 240V ± 10%, 50-60Hz

3 Power Consumption

For HD25/HD25LV

● Bright (Normal): TYP 308W MAX 339W @ 110V AC

TYP 297W MAX 327W @ 220V AC

● ECO Mode: TYP 250W MAX 275W @ 110V AC

TYP 241W MAX 265W @ 220V AC

For HD25e

● Bright (Normal): TYP 240W MAX 264W @ 110V AC

TYP 230W MAX 253W @ 220V AC

● ECO Mode: TYP 212W MAX 233W @ 110V AC

TYP 204W MAX 224W @ 220V AC

4 Keystone correction

● +/-40 degree is the scaler spec.

For HD25/HD25LV

● +/-12 degree is for system angle of V-keystone

For HD25e

● +/- 20 degree is for system angle of V-keystone

5Throw ratio ● 1.5~1.8(D/W) @ 60”

6 Projection lens ● YM40Y

7 Lamp life

For HD25/HD25LV

● Bright Mode (Normal Mode)

3500 Hours Standard @240W,50% Survival Rate

● STD Mode (ECO Mode)

5000 Hours Typical @190W,50% Survival Rate

For HD25e

● Bright Mode (Normal Mode)

4500 Hours Standard @190W,50% Survival Rate

● STD Mode (ECO Mode)

6000 Hours Typical @160W,50% Survival Rate

8 Lamp ● 240W Philp E20.9(For HD25/HD25LV)

●190W Philp E20.9(For HD25e)

HD25/HD25LV/HD25e Condential 1-2

No Item Description

9DMD Chip&Number of

active dots

● 0.65” S600, Dark Chip 3

● Number of active dots:1920x1080

10 Color wheel

For HD25

● 6S (R63G61B56R63G61B56)&7200rpm

For HD25LV/HD25e

● 6S (R81Y41G84C31W52B71)&7200rpm

11 System controller ● TI DDP4422

12 Video compatibility

● NTSC: M/J ,3.58MHz, 4.43 MHz

● PAL: B, D, G, H, I, M, N, 4.43MHz

● SECAM: B, D, G, K, K1, L, 4.25/4.4 MHz

● HDTV: 720p(50/60Hz), 1080i(50/60Hz),1080P(24/50/

60Hz)

● SDTV:480i/p, 576i/p

13 Input signal spec

● VGA-in x2(for HD25e is only VGA-in)

● Composite Video x1

● HDMI v1.4

● Audio input (3.5mm jack)x 2

● RS232 control (9 pin)

● �SB type B(remote mouse simulation)�SB type B(remote mouse simulation)

14 Altitude&Temperature

● Non-operation: Sea Level to 40,000 feet

Operating: Sea Level to 10,000 feet (@23°C);

manual switch to high altitude mode @5000 feet &

above

● Operating: 0 to 10,000 feet (5 to 40ºC)

Opefating Testing:5°C~40°C @ 0~2,500 feet

HD25/HD25LV/HD25e Condential 1-3

Compatibility Resolution Refresh Rate [Hz] Analog Digital

NTSC 720 x 480 60 - -

PAL/SECAM 720 x 576 50 - -

VGA

640 x 480 60 ○ ○

640 x 480 67 ○ -

640 x 480 72 ○ -

640 x 480 85 ○ -

SVGA

800 x 600 56.3 ○ -

800 x 600 60.3 ○ ○

800 x 600 72 ○ ○

800 x 600 85 ○ ○

800 x 600 120 ○ ○

XGA

1024 x 768 60 ○ ○

1024 x 768 70.1 ○ ○

1024 x 768 75 ○ ○

1024 x 768 85 ○ ○

1024 x 768 120 ○ ○

HD720

1280 x 720 50 ○ ○

1280 x 720 60 ○ ○

1280 x 720 120 ○ ○

WXGA

1280 x 768 60 ○ ○

1280 x 768 75 ○ ○

1280 x 768 85 ○ ○

1280 x 768 60 ○ ○

1366 x 768 60 ○ ○

WXGA+ 1440 X 900 60 ○ -

1-2 Compatible Mode

Computer Compatibility

HD25/HD25LV/HD25e Condential 1-4

Compatibility Resolution Refresh Rate [Hz] Analog Digital

SXGA

1280 x 1024 60 ○ ○

1280 x 1024 75 ○ ○

1280 x 1024 85 ○ ○

SXGA+ 1400 x 1050 60 ○ ○

�XGA 1600 x1200 60 ○ ○

HDTV

1920 x 1080p 24 ○ ○

1920 x 1080p 30 - ○

1920 x 1080p 50 ○ ○

1920 x 1080p 60 ○ ○

HDTV 1920 x 1080i 50 - ○

1920 x 1080i 60 - ○

SDTV 720 x 576i 50 - ○

SDTV 720 x 576p 50 - ○

SDTV 720 x 480i 60 - ○

SDTV 720 x 480p 60 - ○

Note: If the Computer Compatibility supportive signal is different from User’s Manual,

please refer to User’s Manual.

HD25/HD25LV/HD25e Condential 2-1

Chapter 2

Disassembly Process

2-1 Equipment Needed & Product Overview

1. Screw Bit (+): 105

2. Screw Bit (+): 107

3. Screw Bit (-): 107

4. Hex Sleeves: 5 mm

5. Tweezers

6. Projector

* Before you start: This process is protective level II. Operators should wear electrostatic chains.

* Note: - If you need to replace the main board, you have to record the lamp usage hour.

- Some related contents please refer to common SM chapter 2.

Other manuals for HD25

This manual suits for next models

Table of contents

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB operating instructions

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

InFocus

InFocus LitePro 560 user guide

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual