Optiguard STAND Smart S User manual
Optiguard sp. z o.o.
ul. Aleksandrowska 6-10, 87-100 Toruń
NIP 956-213-03-91
Phone +48 56 654 71 33 1/ 5
INSTALLATION INSTRUCTIONS
SUGGESTED USE
Stand Smart S is the standalone anti-theft protection dedicated to
smartphones and tablets.
UMH3 sensor ensures an aesthetic product presentation at an angle
of 30 degrees.
Small size assured optimum visibility of the product.
The image below shows the components needed to assemble the
whole system.
1) Stand Smart S
2) smartphone
3) USB 5V/2A power supply
4) cleaning tissue with izopropylan
Cleaning tissue with izopropylan assures the proper preparation
of the surface under Optiguard stickers.
WARNING!
After connecting the device to a charger, a periodically blinking yellow diode in the base indicates lack of any programmed remote controls.
STAND Smart S
Optiguard sp. z o.o.
ul. Aleksandrowska 6-10, 87-100 Toruń
NIP 956-213-03-91
Phone +48 56 654 71 33 2/ 5
INSTALLATION INSTRUCTIONS
Using the cleaning tissue with izopropylan, we can prepare
the surface of the furniture, to which Stand Smart S will be
attached. After cleaning the furniture, wait until the cleaning
substance evaporates.
Take off the protective papers from the stickers.
Place the cable (with USB connector) in a special groove located
in the housing of Stand Smart S.
Stick Stand Smart S to the furniture and press for approx.
10 seconds for good bonding of the sticker adhesive.
STAND Smart S
Optiguard sp. z o.o.
ul. Aleksandrowska 6-10, 87-100 Toruń
NIP 956-213-03-91
Phone +48 56 654 71 33 3/ 5
INSTALLATION INSTRUCTIONS
Using the cleaning tissue with izopropylan, we can prepare the
surface of the furniture, to which the sensor will be attached.
After cleaning, wait until the cleaning substance evaporates.
Take off the protective paper from the sticker of UMH3 sensor.
Stick the phone to the sensor and press for approx. 10 seconds
for good bonding of the sticker adhesive.
The charging cable allows to connect the protective sensor.
The smartphone will be simultaneously charged and protected.
STAND Smart S
Optiguard sp. z o.o.
ul. Aleksandrowska 6-10, 87-100 Toruń
NIP 956-213-03-91
Phone +48 56 654 71 33 4/ 5
INSTALLATION INSTRUCTIONS
Plug the end of the cable with the sticker of "ALARM" in USB of
the smartphone.
USB 5V/2A charger provides adequate power for
Stand Smart S and allows to charge the protected product.
Plug the cable from Stand Smart S with USB connector in the
charger with USB port.
STAND Smart S
Plug USB charger with connected Stand Smart S into a power
outlet (AC 230V).
Optiguard sp. z o.o.
ul. Aleksandrowska 6-10, 87-100 Toruń
NIP 956-213-03-91
Phone +48 56 654 71 33 5/ 5
INSTALLATION INSTRUCTIONS
Powered Stand Smart S will activate within 3 seconds. Short
acoustic signal and periodically blinking red LEDs in the sensor
confirm activation of the system. Finished!
STAND Smart S
Table of contents
Other Optiguard Rack & Stand manuals
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
