Opticon LGZ 7225 User manual

User’s Manual

LGZ 7225

Long Range Handheld

CCD Scanner

25-ULGZMU01-01

Keyboard Wedge Interface

USB Interface

RS232 Interface

8 Olympic Drive

Orangeburg, NY 10962

Tel 800.636.0090

Fax 845.365.1251

www.opticonUSA.com

Contents

General Information

Unpacking .

Opticon Customer Service and Support

Installation

Default Settings

Interface Selection

Scanning Modes

Beeper Settings

Symbology Options

Prefix/Suffix Strings

Transmission Setting

Parameter Settings List

Programming Bar Codes

Getting Started

General Information

The LGZ 7225 CCD Scanner utilizes state-of-the art imaging technology similar to that found in digital

cameras, fax machines and video camcorders. The captures an “image” of the bar code and converts it into

digital signals that the host computer understands.

The scanner automatically recognizes most common bar code symbologies.

The scanner, which utilizes miniature, surface-mounted electronics, has no moving parts and will provide

years of trouble-free operation.

The LGZ 7225 is available in several different interface configurations.

Keyboard Wedge (PS2 or AT/XT)

RS 232

USB

Unpacking

Remove the scanner from its packaging and inspect it for damage. Save the carton and packing material. If

the scanner was damaged in transit, call the dealer or distributor from whom you purchased it. If you

purchased it directly from Opticon, call Opticon Customer Service Dept. at 800-636-0090.

Opticon Customer Service and Support

If you have any questions or need assistance with installing or programming your scanner call Opticon

Customer Service Department at (800) 636-0090.

Before you call, record the model number of the scanner. This information is located on the bottom side of

the scanner. Also please have the scanner available plus some bar codes to scan.

LGZ7225 Long Range Handheld CCD Spec

160 g (cable not included)

Cable - K/B Wedge Straight 2.0 m

Cable - universal type Straight 2.3 m

Connector type RJ-45 phone jack connector

Case material ABS plastic

Cushion material Rubber

Electrical

Input Voltage 5 VDC r0.25V

Power - Operating 1275 mW

Power - Standby 600 mW

Current - Operating 255 mA @ 5VDC

Current - Standby 120 mA @ 5VDC

DC Transformers Class 2; 5VDC @ 450 mA

Agency listing UL, FCC Class A

Environmental

Operating Temperature 0qto 45qC (32qF to 113qF)

Storage

-40qC to 60qC

(-40qF to 140qF)

Humidity

5% to 90% relative humidity,

non-condensing

Light Level Up to 60000 Lux

Shock 1.5m drop onto concrete

Contaminants

Seals to resist airborne particulate

contaminants

Ventilation None required

Default Setting for each barcode shown as below:

Code Type Read Checksum

Verifacation

Checksum

Transmission

Code ID

UPC-A X X X A

UPC-E X X X E

EAN-13 X X X F

EAN-8 X X X FF

Code-39 X *

Interleaved 2of5 X X i

Industrial 2of5 i

Matrix 2of5 B

Standard 2of5 i

China Post t

Codabar %

Code-128 X X #

Code-93 &

Code-11 O

MSI/Plessey @

UK/Plessey @

Telepen S

Italian Pharmaode. p

Programming

method

Manual (Reading special barcode) DOS

command through RS-232, Windows

configuration program

Program upgrade Enabled by built-in flash memory

Programmable

characteristics

Code type selection, check digit

selection Decoding option Decoding

option Transmitted character delay,

Header selection, trailer selection,

message suffix, good read beep tone

and volume, scanner trigger selection

Keyboard emulation type

(intermessage delay, keyboard type

and keyboard language)

Serial interface type (ACK/NAK,

Xon/Xoff, RTS/CTS, good read LED

control, start/stop bits)

Programming the

LGZ7225

To program the LGZ7225 you must scan a series of

programming barcode in the correct order. Fold out the back

cover of this manual. You will see a table of alphanumeric

barcodes, which are used to program the various options

presented.

To program each option, you must:

1. Scan the Program barcode on the parameter setting part.

2. Enter the option mode by scanning the Option Bar Code

(also on the Parameter setting part).

3. To the right of the option barcode, the necessary

alphanumeric inputs are listed. Scan these alphanumeric

entries from the back fold out page. To confirm above

steps, you must scan the Finish barcode on the back fold

out page.

4. Once you have finished programming. Scan the Exit

barcode, listed on the lower right hand corner of each

parameter setting part.

Option Bar Code Option Alphanumeric Entry

Interface

selection

Keyboard Wedge

RS-232

Wand emulation

USB

Keyboard/RS-232

Auto detection

reserved

00ഖ

Back Fold Out

Finish barcode

Exit Barcode

Option Barcode

Program Barcode

Exit

Program

Interface Selection

This decoder built-in scanner comes in one model and

supports interfaces such as keyboard wedge, RS232 serial

wedge, wand emulation, and the latest USB interface. In

most of the cases, simply sutilizing the an appropriate cable with

a device code will work for a specific interface.

Interface selection: You can change factory interface

default for other type interface. By plugging different cables,

setting correct interface, then the scanner will be changed to

another interface. However, you must make sure which cable

you need.

Keyboard/RS232/UBS Auto detection: By setting this

function, it will automatically select the Keyboard wedge or

RS-232 or UBS interface for user.

Program

Option Bar Code Option Alphanumeric

Entry

Interface selection

Keyboard Wedge

RS-232

Wand emulation

USB

Keyboard

/RS232/USB

Auto detection

Reserved

04ഖ

Note:ഖ-Default

Exit

Keyboard wedge

As a keyboard interface, the scanner supports most of the

popular PCs and IBM terminals. The installation of the wedge

is a fairly simple process without any changes of software or

hardware.

Keyboard Type: Select keyboard type connector of your

host computer. Scanner must be selected to the appropriate

host interface cable converter.

Program

Option Bar Code Option Alphanumeric

Entry

Keyboard type

IBM AT, PS/2

Reserved

00ഖ

Exit

Table of contents

Opticon LGZ 7225 User manual

Popular Barcode Reader manuals by other brands