Optex VX Infinity Series User manual

-1-

INSTALLATION INSTRUCTIONS

No. 59-1935-1

MULTI DIMENSIONAL OUTDOOR DETECTOR

VX InfinityTM series

FEATURES

CONTENTS

VXI-ST Standard model with 2 PIR

WIRED MODEL

VXI-AM VXI-ST with anti-masking

VXI-DAM VXI-AM with micro-wave

The VX InfinityTM series provide highly reliable detection functions, reducing false reports or

report losses. The VX InfinityTM series deliver stable detection performance even in severe

outdoor environments.

-12 m (40 ft.) by 90 degree flexible detection pattern adjustable to 5 ranges

- SMDA Logic for advanced temperature compensation and environmental noise immunity.

- Easy Masking for over spill prevention

- Double Conductive Shielding against bright light disturbance.

- Conduit/TX-Battery Case for both wired and wireless-ready models.

BASIC FEATURES

- Active IR Anti-Masking for detecting covering objects

- Tough Mod Dual Technology based on OPTEX gold-plated microwave module

OPTIONAL FEATURES

INTRODUCTION

1-1 BEFORE INSTALLATION

1-2 PARTS IDENTIFICATION

1-3 DETECTION AREA

INSTALLATION

2-1 BEFORE MOUNTING

2-2 WALL TAMPER WRS-02 (OPTION)

2-3 MOUNTING

2-4 MOUNTING WITHOUT BACK BOX

2-5 MOUNTING WITH BACK BOX

2-6 WIRING

2-7

PLUG-IN END OF LINE RESISTORS (EOL) (OPTION)

2-8 AREA ANGLE ADJUSTMENT

2-9 AREA MASKING

2-10 DETECTION LENGTH ADJUSTMENT

SWITCH SETTING

WALK TEST

LED INDICATION

SPECIFICATIONS

6-1 SPECIFICATIONS

6-2 DIMENSIONS

SETTING OF SPECIAL DETECTION AREA

-2-

Warning

INTRODUCTION

1-1 BEFORE INSTALLATION

Warning

Caution

Failure to follow the instructions provided with this indication and improper handling may cause

death or serious injury.

Failure to follow the instructions provided with this indication and improper handling may cause

injury and/or property damage.

The check mark indicates recommendation.

The nix sign indicates prohibition.

• Sunlight and reflection • Heat source • Objects moving in the wind

0.8 – 1.2 m

(2.64 – 3.94 ft)

Parallel

Tilt

Do not remove the PCB. Keep product away from direct splash.

Mounting height. Keep the detector parallel to the

ground.

Consider the direction a person is

approaching from, as well as the

detection area.

Install the detector in a place where it is free from false alarm factors. For example:

-3-

Cover unit

Main unit

Back box

Back box cap

Wiring sponge

Mounting plate

1-2 PARTS IDENTIFICATION

-Precautions for installing two or more sensors

Masking seal × 3 pcs

For wall mounting

Screw kit

Screw (4 × 20 mm)

Optional accessories

Wall tamper (WRS-02) PLUG-IN EOL (PEU)

1.0 m (3.28 ft) or more Less than 1.0 m (3.28 ft)

Do not install two or more VXI-DAMs in side by side or face to face. Doing so may cause

malfunction. VXI-DAM may be installed in back to back. If mounting on the same wall, make

sure that each unit is at least 1.0 m (3.28 ft) apart from the other.

VXI-ST

VXI-AM

VXI-DAM

-4-

fghi

INSTALLATION

1-3 DETECTION AREA

2-1 BEFORE MOUNTING

Control panel Wall tamper (option)

WRS-02

Twist and swage

the wires.

TOP VIEW

SIDE VIEW

Length limiting position 1 (Default)

PIR

Area diagram of horizontal position D

12m

12m 10m 12m10m5m 5m0

10m

ABCEFG

WRS-02 (option)

0 5m 10m 12m

Length limiting position 2

0 5m 10m 12m

Length limiting position 3

0 5m 10m 12m

Length limiting position 4

0 5m 10m 12m

Length limiting position 5

0 5m 10m 12m

Note>>

The maximum detection length may vary as

shown below due to environment conditions.

Remove the cap.

1Open the cover unit.

2Remove the main unit from

the back box.

3Remove the back box

from the mounting plate.

Mount the wall tamper (WRS-02)

on the back of the main unit.

1Run the wire along the wiring

groove.

2Install the unit on the terminal block

and control panel.

Store the connecting

cable in a trench

and seal with a label

already in place.

2-2 WALL TAMPER WRS-02 (OPTION)

-5-

2-3 MOUNTING

Mount the mounting plate.

2-4 MOUNTING WITHOUT BACK BOX

The unit is installed without a back box unless the main unit requires a protrusion off the mounting wall.

Mount the main unit on the mounting plate.

Wall mount Pole mount

Electric gang box mount Conduit installation

Metal band

* Use a metal band with

25 mm or less in width.

Pitch 83.5 mm (3.29 inch)

An electric gang box can be connected. Open the knockout located at

the bottom of the back box.

Connect the pipe and back

box.

When mounting to electric gang

box (single), follow wall mount

instructions.

Wiring hole

Wiring sponge

Note>>

Pay attention to warterproof.

Note>>

It is optional to use the Backbox in hardwired models.

ø 21 mm

2-6

Proceed to

-6-

2-5 MOUNTING WITH BACK BOX

When a certain distance from the mounting surface is required for purposes such as avoiding an

unwanted object, use the back box to install the unit.

Open a wiring knockout on the back box and pass the wire from the mounting plate.

Wiring

Put the top of the back

box on the hook.

Wiring hole

Wiring sponge

Wiring hole

1Open a wiring knockout inside the back box.

2Mount a back box on the mounting plate.

3Mount the main unit on the back box. 4Put the cap on top.

-7-

2-6 WIRING

-Power cable length

The power cable should be limited to the following length.

Wiring terminal is located on the upper part of the main box.

-When setting the resistance value using PLUG-IN EOL

Three types of signals - ALARM,

TROUBLE, and TAMPER - can be

recognized through the combination

of the resistance value and wires for

the TR, COM, and TP terminals.

-When setting the resistance value without

using PLUG-IN EOL

Wire resistors between the appropriate terminals as follows:

This feature may be used when connecting VXI to a control panel that supports the EOL technique.

Terminals <VXI-ST>

Power (+)

Power (-)

Spare

Alarm

Tamper

Aux. input

<VXI-AM> <VXI-DAM>

Power (+)

Power (-)

Spare

Trouble

Common

Alarm

Tamper

Aux. input

WIRE GAUGE

AWG22

(0.33mm2)

290 m

(950 ft)

620 m

(2,030 ft)

240 m

(790 ft)

520 m

(1,710 ft)

160 m

(520 ft)

360 m

(1,180 ft)

12 V

VXI-ST VXI-AM VXI-DAM

Current draw 20 mA Current draw 24 mA Current draw 35 mA

14 V 12 V 14 V 12 V 14 V

450 m

(1,480 ft)

980 m

(3,220 ft)

380 m

(1,250 ft)

820 m

(2,690 ft)

260 m

(850 ft)

560 m

(1,840 ft)

720 m

(2,360 ft)

1,570 m

(5,150 ft)

600 m

(1,970 ft)

1,310 m

(4,300 ft)

410 m

(1,350 ft)

900 m

(2,950 ft)

AWG20

(0.52mm2)

AWG18

(0.83mm2)

COMMON

TROUBLE

ALARM

TAMPER

Type

Insert direction

Caution>>

For details, refer to a note provided with plugs. Make sure to apply the

correct type of plug according to the system

+ - SP TR COM AL TP TP

Triple-EOL

Double-EOL

TAMPER

ALARM

TROUBLE

PLUG-IN EOL

CONTROL PANEL

+ - SP TR COM AL TP TP

TAMPER

ALARM

TROUBLE

2-7 PLUG-IN END OF LINE RESISTORS (EOL) (OPTION)

-8-

2-8 AREA ANGLE ADJUSTMENT

2-9 AREA MASKING

Note>>

When creating a special detection area, refer to the end of this manual.

If there is an unwanted object within the detection area, apply an area masking label to the appropriate area.

Insert the protruding

part of the cover into

the lens hole.

Fit the edge of the

lens.

Slide the lens holder to secure it.

Horizontal position D

(Default)

Horizontal position B

(F: symmetrical

position)

Horizontal position C

(E: symmetrical

position)

Horizontal position A

(G: symmetrical

position)

ABCEFGD

ABCEFG

Unwanted

object (Tree)

1Slide the lens holder and remove the lens holder out

of the cover as shown below. 2Identify positions to mask on the lens and apply a

corresponding strip from the masking sheet 1.

3Insert the lens into the cover. 4Mount the lens holder to the cover.

The angle can be adjusted in

7 levels from A to G.

The detection area becomes

14 zones only when A or G is

selected.

-9-

2-10

DETECTION LENGTH ADJUSTMENT

Both upper and lower detection

area are blocked

IMPORTANT

BOTH DETECTION AREAS MUST BE

BLOCKED FOR DETECTION

Detection!

Detection

Only upper detection area is blocked

Only lower detection area is blocked

MW sensitivity

adjustment knob

1Adjust the PIR detection length by sliding the lower

PIR to the desired position.

2Adjust the MW detection length by rotating the MW

sensitivity adjustment according to the PIR area.

Detection length setting chart

* The detection lengths described above should be used as a guideline.

Position

(Factory

default)

12.0 m

(40.0 ft)

8.5 m

(27.9 ft)

6.0 m

(19.7 ft)

3.5 m

(11.5 ft)

2.5 m

(8.2 ft)

10.0 -17.0 m

(32.1 - 55.8 ft)

7.0 - 12.0 m

(23.0 - 39.4 ft)

5.0 - 8.5 m

(16.4 - 27.9 ft)

3.0 - 6.0 m

(9.8 - 19.7 ft)

2.0 - 3.5 m

(6.6 - 11.5 ft)

Max detection length Detection area

sensitivity

adjustment

12 m

8.5 m

6 m

3.5 m

2.5 m

-10-

DIP switch

1 LED

2 ALARM OUTPUT

3 AUX INPUT

4 ANTI-MASKING

5 MICROWAVE IMMUNITY

SWITCH SETTING

2 4 53

12345

DIP switch 1

OFF ⇔ON

-LED

VXI-ST

VXI-AM

VXI-DAM

POSITION FUNCTION

(Factory default)

OFF

LED ON

LED OFF

DIP switch 2

N.C. ⇔N.O.

-ALARM OUTPUT

VXI-ST

VXI-AM

VXI-DAM

12345

POSITION FUNCTION

N.O.

N.C.

(Factory default)

N.O. output

N.C. output

VXI features can be set on/off by DIP switch settings.

MW sensitivity adjustment

PIR sensitivity selector

Other manuals for VX Infinity Series

This manual suits for next models

Table of contents

Other Optex Security Sensor manuals

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions