Jumper On: After transmitting for a detected movement, any further movement detection will transmit the event code again (and the captured images)
(default).
Jumper Off: PIR Camera has a “sleep time” of approximately 1 minute to conserve power.
3 FEATURES
IMAGE CAPTURE
When the alarm system is armed, the PIR Camera will capture 3 or 6 alarm images in 640 x 480 or 320 x 240 resolutions (programmable from control
panel) upon movement detection. You can also manually request the PIR Camera to take a picture through CIE. The captured images will be transferred
to ZigBee coordinator or CIE for user to view.
WARM UP PERIOD
When the ZigBee system enters arm mode, or when PIR Camera is put into Test Mode, the PIR Camera will warm up for 30 seconds. Do not trigger the
PIR Camera during the 30-second warm up period. If the PIR Camera is under low battery or tamper opened condition, the Blue LED will light up during
the warm up period.
SLEEP TIMER
When Jumper Switch 2 is set to Off, the PIR Camera has a “sleep time” of approximately 1 minute to conserve power. After transmitting for a detected
movement, the PIR Camera will not retransmit for 1 minute. Any detected movement during this period will reset the sleep time to 1 minute. Continuous
movement in front of the PIR Camera will therefore not exhaust the battery.
BATTERY AND LOW BATTERY DETECTION
The PIR Camera uses two 1.5V “AA” Lithium batteries in series connection as its power source. Remove the Battery Compartment Cover and insert
the batteries to activate the PIR Camera.
The PIR Camera features Low Battery Detection function. When the battery voltage is low, the PIR Camera will transmit Low Battery signal to the
coordinator in ZigBee network. If movement is detected under Low Battery condition, the Blue LED will light up for 2 seconds.
When changing battery, after removing the old battery, press the Tamper Switch or the Function Button twice to fully discharge before inserting new
batteries
TAMPER PROTECTION
The PIR Camera is protected by a tamper switch which is compressed when the PIR Camera is properly installed. When the PIR Camera is removed
from mounted surface or its cover opened, the tamper switch will be activated and the PIR Camera will send a tamper open signal to the ZigBee network
coordinator or system control panel to remind the user of the condition. If movement is detected when the tamper switch is open, the Blue LED will light
up for 2 seconds.
PIR Camera will not detect the status of the tamper switch within 5 minutes of inserting battery.
If the Tamper Switch is triggered during this 5-minute non-detection period, the PIR Camera will transmit a tamper status signal to the ZigBee
network coordinator or system control panel immediately after the 5-minute non-detection period.
When the tamper switch is compressed, Factory Resetting the PIR Camera is disabled.
SUPERVISION
The PIR Camera will transmit a supervision signal to report its condition regularly according to user setting. The factory default interval is 30 minutes. The
user can also press the Function Button once to transmit a supervision signal manually.
TEST MODE
Test mode is for you to check the PIR camera’s detection range (not shooting coverage).
To enter Test mode, press and hold the Function button over 3 seconds and release the button to enter the Test mode for 3 minutes.
The PIR camera will warm up for 30 seconds. Please do not trigger the Camera during this warming-up period.
After the warm-up period, you can trigger PIR camera to check IR detection range. If PIR camera is triggered, the Blue LED will light up for 2
seconds.
4 ZigBee NETWORK SETUP
ZigBee DEVICE GUIDELINE
ZigBee is a wireless communication protocol that is reliable, has low power consumption and has high transmission efficiency. Based on the
IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and coordinated for data exchange and signal
transmission.
Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join network after powering on. Since performing a task in
connecting network may consume some power, it is required to follow the instructions to avoid draining battery of a ZigBee device
Ensure your ZigBee network router or coordinator is powered on before inserting battery into the ZigBee device.
Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee device is in use.
Do not remove a ZigBee device from the ZigBee network router or coordinator without removing the battery from a ZigBee device.
JOINING THE ZigBee NETWORK
As a ZigBee device, the PIR Camera needs to join a ZigBee network to transmit signal when a movement is detected. Please follow the steps below
to join the device into the ZigBee network.
THE PIR CAMERA CAN ONLY JOIN ZigBee NETWORK WITHIN 3 MINUTES AFTER POWER ON.
Step1. Remove the Battery Compartment Cover by loosening the Battery Compartment Screw.
Step2. Insert the batteries. Orient the battery according to the polarity indication.
Step3. Make sure the tamper switch is open.
Step4. Within 3 minutes after power on, Press and hold the function button for 10 seconds, release the button when both the Blue LED and
flash LED flash once. Please make sure to enable the permit-join feature on the router or coordinator of your ZigBee network.
Step5. After joining the ZigBee network, the PIR Camera will be registered in the security system in the network automatically. Please check the
ZigBee network coordinator, system control panel, or CIE (Control and Indicating Equipment) to confirm if joining and registration is
successful.
Step6. After joining the ZigBee network, if the PIR Camera loses connection with the ZigBee network, the LED will flash 20 minutes to indicate.
Please check your ZigBee network condition and PIR Camera signal range to correct the situation.
Jumper On
The jumper link is inserted
connecting the two pins.
Jumper Off
if the jumper link is removed
or “parked” on one pin.
