Oneida Air Systems BenchTop User manual
BenchTop
Personal Dust Collector
#XBZ000100
Rev: B 20230428LL Doc. #ZBM000041
Appearance may vary slightly
OWNER’S MANUAL
Patents: www.oneida-air.com/patents
oneida-air.com 1
Table of Contents
System Specications 6
System Dimensions 7
System Contents 8
Assembly Instructions 9
BenchTop Features 12
Maintenance 13
Troubleshooting 15
F.A.Q. 16
Recommended Accessories 17
Warranty Information 19
Notes 20
Oneida Air Systems, Inc.2
System Start-Up Information
WARNING
1. READ and understand ALL instructions and warning labels BEFORE using the dust collector.
2. REPLACE warning labels if they become obscured or removed.
3. ALWAYS follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and
regulations when installing and operating this dust collector.
4. ENSURE that all users of this Dust Collector are informed of all warnings and precautions, safe use, and
maintenance procedures.
5. FULL mental alertness is required. NEVER operate under the inuence of drugs or alcohol, when tired, or
when distracted.
6. DO NOT allow use by or near children.
7. DO NOT allow to be used as a toy. Close attention is necessary when used by or near children.
8. NEVER leave the dust collector running while unattended.
9. TURN OFF and UNPLUG the dust collector BEFORE walking away, servicing, or cleaning. Allow the fan
blower motor to come to a COMPLETE STOP before walking away or performing any maintenance, service,
cleaning, or adjustments. is eliminates the risk of injury from unintended startup or contact with live
electrical components.
10. ENSURE that your dust collector is turned OFF and UNPLUGGED during installation. is eliminates the
risk of injury from unintended startup or contact with live electrical components.
11. ONLY use the dust collector for its intended purpose as described in this manual. DO NOT force it or
an attachment to do a job for which it was not designed. Consult this owner’s manual or reach out for
recommended accessories.
12. ENSURE enough air volume is at the suction point to capture all the particulate generated.
13. NEVER make modications without prior approval from Oneida Air Systems. Modifying the dust collector
or using it dierently than intended will void the warranty and may result in malfunction or mechanical
failure that leads to serious personal injury or death!
14. DO NOT locate or operate the system in moist, wet, poorly lit, or cluttered environments. Operating in these
areas can create shock hazards, increase the risks of accidents and injury, and/or lower the operating lifespan
Before Purchasing or installing a dust collection system the process owners/operators
are cautioned to do so in accordance with prescribed Federal, State, Local, OSHA, NFPA,
and any other applicable codes or regulations relating to the type of dust(s) you are
collecting.
This manual contains specific precautionary statements relative to worker safety. Read
thoroughly and comply as directed. The most up to date safety information can be found
on our website: oneida-air.com/safety
oneida-air.com 3
System Start-Up Information (Continued)
of the dust collector.
15. DO NOT install in classied hazardous atmospheres without an enclosure rated for the application. System
Location must account for wind, seismic zone, and other load conditions. Codes may regulate acceptable
locations for installing dust collectors. Consult with the appropriate authorities having jurisdiction to ensure
compliance with all national and local codes regarding dust collector installation. Equipment must be
anchored in a manner consistent with local code requirements. Anchors must be sucient to support dead,
live, seismic, and other anticipated loads. Consult a qualied engineer for nal selection of anchorage.
16. ENSURE exhaust air is properly vented. It should NOT be vented into a wall, a ceiling, or a concealed space
of a building. Personal injury, death, and/or property damage can result from material discharge during
venting. e risk of personal injury and/or property damage can be minimized or avoided by locating vented
equipment outside buildings and away from normally occupied areas. If exhaust air is vented outside, you
must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop from furnaces,
water heaters, or other appliances
17. INSPECT and MAINTAIN REGULARLY. Keep the dust collector in proper working order. A machine that
isn’t properly maintained, not working as it should, has been dropped, damaged, le outdoors, or dropped in
water could malfunction leading to serious personal injury or death!
18. AVOID CORD DAMAGE. DO NOT pull or carry by cord. DO NOT use cord as handle. DO NOT unplug
by pulling on cord. To unplug, grab the plug, DO NOT close door on cord or pull cord around sharp edges or
corners. DO NOT run dust collector over cord. DO NOT handle cord/plug with wet hands. Keep cord away
from heated surfaces.
19. ALWAYS check for damaged parts. A part that is damaged should be carefully checked to determine that
it will operate properly and perform its intended function. Immediately repair or replace damaged or mis-
adjusted parts before operating machine.
20. DO NOT put any object in openings. DO NOT use with any opening blocked.
21. ALWAYS wear a NIOSH approved respirator during operation. Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects
or other long-term respiratory damage
22. ALWAYS keep hair, loose clothing, ngers, and all parts of body AWAY from openings and moving parts.
23. ALWAYS wear ANSI-approved safety glasses or a face shield when operating or observing machinery and
when emptying dust bin.
24. ALWAYS wear hearing protection during extended periods of operation.
Oneida Air Systems, Inc.4
System Start-Up Information (Continued)
1. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.
2. DO NOT operate the dust collector in areas where explosion risks are high. Areas of high risk include, but
are not limited to, areas near pilot lights, open ames, or other ignition sources.
3. ONLY operate dust collector in locations that include a re suppression system or have a re extinguisher
available nearby.
a. e ABC type (dry chemical) is generally a good choice for small wood shops.
b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire
Extinguishers).
4. DO NOT allow accumulation of layers of ne dust on horizontal surfaces. Especially overhead lights,
electrical boxes and fuse panels which can ignite dust. Keep the oor around the system clean and free of
scrap material, oil, grease.
5. ENSURE all equipment and ductwork is electrically grounded.
6. ALWAYS consult an electrician or qualied service personnel about wiring practices and electrical codes
in your area. ONLY allow an electrician or qualied service personnel to do electrical installation or repair
work.
7. ALWAYS disconnect power before accessing or exposing electrical equipment. Improper wiring can cause
re, electrocution, injury, or death.
8. DO NOT use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
9. DO NOT use to pick up liquids, ammable liquids, or combustible liquids, such as gasoline, or use in areas
where they may be present.
10. DO NOT use to pick up VOCs, acids, corrosives, or ammable fumes.
11. DO NOT use excessively large wood waste bins. Wood dust mixtures are highly ammable and can be
explosive
FIRE HAZARDS
Process owners/operators retain all responsibility for the suitability of fire and explosion
hazard mitigation, suppression, and isolation strategies and to follow all applicable
federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and regulations
when installing and operating this dust collector.
Improper operation of a dust control system may contribute to conditions in the work
area or facility that could result in severe personal injury and product or property
damage.
Oneida Air Systems assumes no responsibility or liability for the suitability of any fire and/
or explosion mitigation strategy, or any items incorporated into a collector as part of an
owner/operators hazard mitigation strategy.
oneida-air.com 5
Customer Service Dept.
1-866-387-8822 • support@oneida-air.com
System Start-Up Information (Continued)
12. ALWAYS check your dust bin for smoldering materials before leaving the shop.
13. NEVER introduce sparks or sources of ignition into the dust collector. Sparks can be generated in several
ways:
a. High speed sanders, abrasive planers, saws, and edgers may strike foreign material and create a red-hot
metal fragment.
b. Knots in hardwood can create frictional sparks.
c. Trapped metal, when drawn into the dust collection system, can spark against ductwork.
d. Check wood stock for old nails and screws which can create red-hot metal fragments.
14. DO NOT overload woodworking equipment, especially sanders, as excessive frictional heat can
spontaneously ignite dust. Sanders can produce concentrations of dust well into the combustible range.
15. ALWAYS check that all dust collection equipment is properly selected and sized for the intended use.
Authorities with jurisdiction should be consulted before installing to verify local codes and installation
procedures. In the absence of such codes, install collector according to the National Electric Code, NFPA No.
70-latest edition and NFPA 91, NFPA664 Code (NFPA 654 if combustible dust is present).
Oneida Air Systems, Inc.6
System Specications
OPERATION
Airow Variable Speed 0 - 481 CFM
Horsepower 0.3HP
Phase Single-Phase
Voltage 110V
Cycle 60HZ
Amperage Draw 3A
On/O Switch Analog Variable Speed Control
Power Cord Length 6'
Plug Type NEMA 5-15P
Noise Level 62.5 to 74 dBA
SYSTEM DIMENSIONS AND CONSTRUCTION
Primary Build Materials Cold Rolled Steel with a powder-coated nish
Overall Weight 20 lbs
Pre-Filter Dimensions 16 x 24-1/4 x 1/2"
Main Filter Dimensions 16 x 25 x 3"
Outer Filtration / Material MERV 5 / Polyester
Main Filter Filtration / Material MERV 15 / Synthetic
oneida-air.com 7
System Dimensions
Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.
16-1/2"
419 mm
9-3/4"
248 mm
25-1/2"
648 mm
Oneida Air Systems, Inc.8
B
C
D
E
F
H
J KI
G
System Contents
Please unpack the parts carefully and conrm you have received each item listed here.
*Components are pre-installed at the factory and are listed here for maintenance and convenience. e pre-installed
components will be referred to as the BenchTop Assembly (A).
ID Part number Part description Qty
A XBZ000100 BenchTop Assembly 1
B* BTB000100 Fan Assembly 1
C* FCS162503 Main Filter 1
D* FCS000001 Pre-Filter 1
E* RBB000100 Frame Assembly 1
F BTV000001 Left Vane 1
ID Part number Part description Qty
G BTV000003 Top Vane 1
H BTV000002 Right Vane 1
I* RGC062524 24" Cork Strip 1
J* STX000351 Nylon Foot 2
K WCW000007 AC Cord 1
If you cannot find an item on the list, examine the packaging materials very carefully for nested items. Please
note that certain components have been pre-installed. There may be hardware leftover.
This manual suits for next models
1
Table of contents
Other Oneida Air Systems Dust Collector manuals
Oneida Air Systems
Oneida Air Systems Dust Deputy AXD990003 User manual
Oneida Air Systems
Oneida Air Systems V1500 User manual
Oneida Air Systems
Oneida Air Systems Pro 1500 User manual
Oneida Air Systems
Oneida Air Systems Smart Dust Collector User manual
Oneida Air Systems
Oneida Air Systems Dust Deputy AXD001004 User manual
Oneida Air Systems
Oneida Air Systems 8491685 User manual
Oneida Air Systems
Oneida Air Systems Deluxe Dust Deputy User manual
Oneida Air Systems
Oneida Air Systems Supercell XSK000014 User manual
Oneida Air Systems
Oneida Air Systems Dust Deputy AXD001004 User manual
Oneida Air Systems
Oneida Air Systems XCKM013000 User manual
Oneida Air Systems
Oneida Air Systems V-1500 1.5hp User manual
Oneida Air Systems
Oneida Air Systems Mini-Gorilla User manual
Oneida Air Systems
Oneida Air Systems Supercell XSK000035 User manual
Oneida Air Systems
Oneida Air Systems Super Dust Gorilla User manual
Oneida Air Systems
Oneida Air Systems Super Dust Gorilla User manual
Oneida Air Systems
Oneida Air Systems Super Dust Gorilla 2hp User manual
Oneida Air Systems
Oneida Air Systems Pro 1500 User manual
Oneida Air Systems
Oneida Air Systems Dust Deputy AXD001004 User manual
Oneida Air Systems
Oneida Air Systems Vortex DCS User manual
Oneida Air Systems
Oneida Air Systems Gorilla XXP999901 User manual
