Olympia electronics GR-490/WP User manual

Page 1 from 7923493000_09_003

GENERAL

These devices are used indoors (ta 40 C) in

places where emergency luminaires are

needed. The luminaires GR-490/WP and

GR-492/WP are suitable for corridors lighting

and the GR-491/WP and GR-493/WP for

open area lighting. Each device must be

permanently connected to mains power

supply. In normal operation the battery is

charging. In case of a mains power supply

failure, the device enters emergency mode

and the illumination LED turns on. When the

mains power supply is restored the device

turns to normal operation.

INSTALLATION

To install the luminaire follow the installation

instructions οn page 3.

Battery Charging

The battery charging is completely controlled

by microprocessor and is protected from

complete discharge and overcharge.

Battery Cut-off

The luminaire enters in this mode when the

mains power supply fails and battery has lost

its energy. During this mode the luminaire

enters the idle state and battery consumption

is negligible, in order to be protected from

deep discharge.

Manual Test

This test can be done by using the A-1900

card as described on page 6. The light source

and the emergency circuit of the device are

tested. The manual test can be conducted

only if the mains power supply and the battery

are connected. During this test period the

LAMP TEST LED will blink.

Manual Autonomy Test

A duration test can be conducted by holding the

A-1900 card steadily for 5 to 10 seconds. In

order to be performed, the mains power supply

and the battery should be connected. The

luminaire enters emergency mode, the charge

LED is turned OFF and the Battery Fault led

starts to blink. The test is performed until the

battery is fully discharged.If at the end of the

test the autonomy is low then the Battery Fault

LED will be ON. If the result of the test is good

then the luminaire enters charging mode and

the Charge led starts to blink until the batteries

are fully charged.

WATERPROOF SELF TESTING NON-MAINTAINED EMERGENCY CEILING MOUNTED LUMINAIRES

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

CONSTRUCTION MATERIAL

EXTERNAL DIMENSIONS

WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERY (Ni-Mh)

CHARGE TIME

INDICATIONS

BATTERY PROTECTION

MINIMUM DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

EMERGENCY ILLUMINATION

LIGHT SOURCE

24 hours

LED Charge , Lamp Fault LED, Battery Fault LED / Magnetic Test Contanct

Deep discharge and overcharge protection

IP65

1 white power LED

5 to 40 C

Up to 95%

3 years (1 year for the battery)

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

3 hour

280lm 140lm

576gr.

220-240V AC / 50-60Hz

TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 7)

GR-490/WP GR-491/WP GR-492/WP GR-493/WP

ABS/PC, PC

158 x 158 x 60,4mm (without decorative bezel) - 195 x 195 x 60,4 (with decorative bezel)

Thank you for your trust in our products

Olympia Electronics - European manufacturer

4.8V/1.2 Ah

3.9W / 4.4VA

1.5 hour

Automatic Operational Test

This test includes all the operations that are

provided in manual test and is conducted

automatically every 15 days. In order to be

performed, the mains power supply and the

battery should be connected.

Automatic Autonomy Test

The Automatic Autonomy Test tests the

device’s back up operation and emergency

duration. This test is conducted automatically

every 6 months. In order to be performed, the

mains power supply should be connected and

the battery must be fully charged. If the

battery is not fully charged, the test is

postponed until the battery is completely

charged. If during this test, the autonomy is

less than nominal then the battery fault LED

will permanently be on and the battery must

be replaced.

Back Up Operation

The autonomy duration of battery during

emergency mode must be at least as the one

stated in the list of the technical

characteristics. During emergency mode, a

light source test is also performed.

Resetting Errors

Hold the A-1900 card in TEST position for 10

to 15 seconds in order to delete all LED

indicated errors. Then the device enters

regular operation mode.

Connection to module (After request)

This luminaire can be connected to any of the

following modules: Remote module, address

module, wireless module and fault relay

module. If you connect it to a module that

supports inhibit or rest mode, you should

know that these commands can be cancelled

only during normal mode (ie. not in

emergency). For installation refer to step 3 of

the istallation procedure in page 3.

Also refer to the user’s manual of each

module for additional information.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance

or testing must be done by authorized

personnel only.

2. The device must be connected to the

mains power supply through a fuse that is

dependent on the total line’s power load.

3. In case of battery or lamp replacement,

these must be replaced by parts with same

type, by the manufacturer or by a competent

person.

4. In case of inactive use for a period

greater than 2 months, disconnect the

battery by pulling out the battery’s connector.

5. I s not allowed to discard batteries in t i

to common trash bins, they must be

discarded only in battery recycling

points. Do not incinerate.

Indication LED status (mains on)

Charge

On: Fully charged.

Οff: No battery (No charging current

or disconnected battery).

Blink: Charging.

Lamp Fault

Οn: Faulty LED.

Off: LED OK.

Blink: Operational Test.

Battery Fault

Οff: Battery OK.

ON (With Charge LED ON): Autonomy or

low battery problem (the battery must be

replaced).

Blink (With Charge LED Off): Autonomy test

is performed.

923493000_09_003

Page 2 from 7

Battery

Fault

Lamp

Fault

Charge

Indicators

GR-490/WP, GR-492/WP GR-491/WP, GR-493/WP

923493000_09_003

Page 3 from 7

INSTALLATION INSTRUCTIONS

cable

entry

hole

Corridor

lighting

ATTENTION!!!

During installation follow this light

direction.

Open

area

lighting

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws without removing them and remove the diffusor.

2. Install the battery connector to its corresponding connector on the main pcb.

3. Install the cable grommet in the open hole of the plastic base and open a hole in the center of the

grommet using a small screw driver. Pass the power cable through the hole in the grommet (If required,

open another cutout cable entry hole and install the second supplied cable grommet).Connect the cables

as shown in the photograph. Use the supplied self adhesive pad and cable tie to anchor the cable. If you

use a module pass the 2 signal cables on the A, B terminals minding the correct polarity. Depending on the

module that will be used, the cables that will be used, have different names. In A, signal +L, C are also

connected, while signals -L, NC/NO in the terminal B.

4 Reinstall the diffusor and re-tighten the 4 screws in a diagonally manner with a torque of N*m. 0,9 .

NOTE!! After finishing the installation you must power the luminaire for at least 24 hours in order

to completely charge the battery. The rated autonomy duration can be achieved after that time.

Initial installation

Required opening

14.5x14.5cm

wall plug wall plug

screwsscrews

plastic

mounting

bracket

luminaire’s

base

923493000_09_003

Page 4 from 7

MOUNTING IN SUSPENDED CEILING

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws (figure 1) without removing them and remove the diffusor.

2. Install the supplied cable grommet from the inside of the plastic base (figure 2).

3. Install the two plastic brackets with the four screws (figure 3).

4. Mark the positions of the mounting holes on the brackets.

5. Install the two supplied plaster board plugs by screwing them on the plaster board ceiling.

6.Open a cable entry cutout hole on the plastic base and follow step 3 in the “initial installation”

section.

7. Re-install the front cover that was removed in step 1.

8. Use the supplied screws to fasten the luminaire to the plaster board plugs (figure 8) that were

previously installed on the plaster board ceiling.

9. Finally, install the supplied decorative bezel (figure 9). The notch on the bezel must be

located on the left side of the luminaire (figure 10).

Other

possible

cable entry

holes

923493000_09_003

Page 5 from 7

MOUNTING IN SUSPENDED CEILING

SURFACE MOUNTING

washer

rabber o-ring

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws without removing them and remove the diffusor.

2. Use a drill with a 3,5mm bit to open the 4 mounting holes (figure 2) located in the plastic base..

3. Place the luminaire on the desired mounting location and mark and drill these 4 holes. Fit the

supplied 4 plastic mounting plugs to these drilled holes on the mounting location.

4. If the cable entry hole is not suitable then use one of the supplied cables grommets to cover the

holes and open another cable entry cut out hole (figure 3). Follow step 3 of the “ initial installation

procedure”.

5. Mount the base to the desired location by using the supplied screws, washers and o-rings in

each mounting hole(figure 5).

6. Re-install the cover that was removed in step 1.

LED MODULE CHARACTERISTICS

Olympia Electronics S.A.

65 °C max. across the board

2,8-2,9V DC3-3,1V DC

1W2W

0405183

GR-490/WP

GR-491/WP

GR-492/WP

GR-493/WP

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:X: Self contained

0: Non maintained (*)

A: Including test device

E: With non-replaceable lamp(s)

F: Automatic test gear complying

with IEC 61347-2-7 denoted EL-T

90: 1.5 hour duration

180: 3 hours duration

(*) Non Maintained operation: The luminaire turns on illumination source, only in case of power supply

failure.

fixed connection between main pcb and led module

TEST

A-1900

Test and Faults Reset operations with the A-1900 card (not

included and available after request). For lights test, you

must place the card in front of the TEST indicator and remove it

immediately. For Autonomy Test, you must place the card in

front of TEST and hold it for 5 to 10 seconds.

To reset errors you must place the card in front of TEST by

holding it for 10 to 15 seconds and removing it.

923493000_09_003

Page 6 from 7

Battery replacement

It can be done only by a competent person and after the mains interruption.

1. Detach the front cover by applying pressure using a flat blade screw driver. Next, unfasten the four

retaining screws without removing them and remove the diffusor.

3. Disconnect the connector and remove the old battery.

4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in

the position of the old one.

5. Replace the removed parts and power the device.

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

CAUTION : Do not view directly with bare eyes

Note!! If a module will be used (except the fault

relay module), then the installer should fill in, on the

specification label, the letters B C.

X081 0A E F

The light source of this luminaire is not replaceable when the light source reaches its end of life

the whole luminaire shall be replaced.

ATTENTION!!!

923493000_09_003

Page 7 from 7

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty

is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which

accompanies each product. This warranty ceases to exist if the buyer does not follow the technical

instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods

provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully

agreed to them in writing. Products that have been damaged can be returned to the premises of our

company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the

buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the

buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

This manual suits for next models

Table of contents

Other olympia electronics Lantern manuals

olympia electronics

olympia electronics Classic Light Series User manual

olympia electronics

olympia electronics SLD-28/DZ User manual

olympia electronics

olympia electronics OLY-1004/WP/ADR User manual

olympia electronics

olympia electronics EASY LIGHT Series User manual

olympia electronics

olympia electronics GR-8/leds User manual

olympia electronics

olympia electronics WATERPROOF POWER LIGHT Series User manual

olympia electronics

olympia electronics GR-940/15L/MAR User manual

olympia electronics

olympia electronics OLY-500 User manual

olympia electronics

olympia electronics GR-490/WP/ADR User manual

olympia electronics

olympia electronics Power Light Series Operator's manual

olympia electronics

olympia electronics GR-2110 User manual

olympia electronics

olympia electronics SLIM LIGHT Series User manual

olympia electronics

olympia electronics GR-8/leds User manual

olympia electronics

olympia electronics GRL-38/90/M User manual

olympia electronics

olympia electronics GR-427/12L User manual

olympia electronics

olympia electronics WEATHER LIGHT Series User manual

olympia electronics

olympia electronics LLB-26/90 User manual

olympia electronics

olympia electronics POWER LIGHT Series User manual

olympia electronics

olympia electronics GR-108/12L/90 User manual

olympia electronics

olympia electronics BAU LIGHT Series User manual

olympia electronics

olympia electronics KLIN-20/ST/ADR User manual

olympia electronics

olympia electronics Slim Light Series User manual

olympia electronics

olympia electronics GR-290/WP User manual

olympia electronics

olympia electronics GR-490/ADR User manual

Popular Lantern manuals by other brands

KYOWA

KYOWA KW-9114 instruction manual

Stahl

Stahl ECOLUX 6610 Series operating instructions

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Operator's manual

PRG

PRG VARI LITE VL5 Service manual

Raytec

Raytec VARIO2 series installation guide

ENSA

ENSA LEDBT18WS2 installation instructions

LUG

LUG OFFICE LB LED N/T Installation instruction

GE Wallighter 250 instructions

Draper

Draper RLEDL19/B instructions

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Assembly & fitting instructions

Panasonic

Panasonic EY3741B57 operating instructions

Clas Ohlson

Clas Ohlson LCC8T instruction manual

Coolon

Coolon WDN-140 manual

Holiday Travel

Holiday Travel 834873 manual

BEGA

BEGA 84 036 Instructions for use

BEGA

BEGA 33 596 Instructions for use

Dale Tiffany

Dale Tiffany GT701162 Assembly instructions

Wagan

Wagan Brite Nite Pop-Up USB Lantern user manual

olympia electronics GR-490/WP User manual

Popular Lantern manuals by other brands