Olympia electronics BAU LIGHT Series User manual

The light source contained in this luminary shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

NOTE!! The installer should fill in, on the specification

label, the letter G if the luminaire is used as a safety sign.

(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the mains

power supply or not.

Non Maintained operation: The luminaire lights its illumination source, only in power supply’s failure.

ADDRESS OPERATION

For address operations refer to the installation

manual of the panel. Please see manual of CBS

panel GR-8600 for maximum number of

luminaries that can be interconnected.

GENERAL

1. Operations for installation, maintainance or

testing must be done by authorized personnel

only.

2. The device, must be connected only to the

GR-8600 panel via its ADR line.

3. The user must set the address before

installation. To address the device see on page

Thank you for your trust in our products

Olympia Electronics - European manufacturer

923753002_09_002

TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 1)

Operation temperature range

Relative humidity

Construction materials

External dimensions

Typical weight

Guarantee

Mains voltage

Maximum power consumption

Degrees of cover protection

Produced in accordance with

Light source intensity

18-30V DC

-30 to 50 C

up to 95%

3 years

IP 54

200lm

2.5W

ABS/PC, PC

551 gr.

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547

Page 1 from 3

LED MODULE CHARACTERISTICS

Olympia Electronics S.A

45 °C max. across the board

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

Z: Central supply

1: Maintained (*)

C: Including inhibiting mode

G: Internally illuminated safety sign

12-14V DC

2.4W

2505195

“BAU LIGHT” SERIES ADDRESSABLE LUMINARIES FOR GR-8600 CBS

GR-750/CBS/24V/ADR/HP/LL

GR-751/CBS/24V/ADR/LP/LL

GR-752/CBS/24V/ADR/HP/HL

GR-753/CBS/24V/ADR/LP/HL

1.5W

350lm

Viewing distance *15m, **17m 15m 15m

358 x 85 x 88 mm358 x 125 x 88 mm 358 x 85 x 88 mm 358 x 125 x 88 mm

579 gr. 579 gr. 551 gr.

12-13.5V DC

1.1W

Non-reversible connection between main pcb and led module

35 °C max. across the board

Z1C

*15m, **17m

GR-750/CBS/24V/ADR/HP/LL

GR-751/CBS/24V/ADR/LP/LL

GR-752/CBS/24V/ADR/HP/HL

GR-753/CBS/24V/ADR/LP/HL

*15m: When the luminary is installed on a wall.

**17m: When luminary is installed on the ceiling.

Page 2 from 3

Luminary Installation Procedure

923753002_09_002

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty

is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which

accompanies each product. This warranty ceases to exist if the buyer does not follow the technical

instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods

provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully

agreed to them in writing. Products that have been damaged can be returned to the premises of our

company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the

buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the

buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

1 Place a flat blade screwdriver to the plastic hook and pull up gently to release the diffusor.

2 Remove the reflector.

3 Remove the led strip.

4 Use the included mounting parts to mount the base plastic.

5 Always use round mains cable, with a suitable diameter to fit tightly into the gasket.

ATTENTION!! The cable must not be deformed in any way (This requirement is

important to ensure the ΙΡ rating). Always refer to GR-8600 manual regarding to the

cable’s cross section’s selection. Install the included gasket into the cable entry hole (verify

that is not deformed). Make a hole in the center by using a small screwdriver. Pass the

communication cables through the hole and connect them as shown on the picture (minding

the correct polarity). When there are other luminaries to be connected to the line we

recommend to open a second hole to pass the second pair of communication cables.

6 If the luminary you installed is the last one, connect the cable to one of the two inputs, as

shown on the picture (minding the correct polarity).

7 Address the device though the dipswitch according to the table on page 3.

8 Refit the led strip minding the connection with the P.C.B.

Warning!! The holes of the led strip must be fit in the projections of the base.

9 Refit the reflector (mind the correct orientation) and tighten the screws.

10 Refit the diffusor (mind the correct orientation) and power on the device. (see GR-8600

manual).

Page 3 from 3

Addressing Table

Address Dipswitch

setting AddressAddressAddress Dipswitch

setting

Dipswitch

setting

Dipswitch

setting

2 3 4 5 6

131

2 3 4 5 6

923753002_09_002

-L

This manual suits for next models

Other olympia electronics Lantern manuals

olympia electronics

olympia electronics GRL-37/90/WP User manual

olympia electronics

olympia electronics GR-220/DUO/M User manual

olympia electronics

olympia electronics GR-938/15L User manual

olympia electronics

olympia electronics GRL-29 WP User manual

olympia electronics

olympia electronics KLIN-20/ST User manual

olympia electronics

olympia electronics OLY-1004/WP/ADR User manual

olympia electronics

olympia electronics Slim Light Series User manual

olympia electronics

olympia electronics POWER LIGHT Series User manual

olympia electronics

olympia electronics SLD-28/DZ User manual

olympia electronics

olympia electronics POWER LIGHT Series User manual

olympia electronics

olympia electronics GR-940/15L/MAR User manual

olympia electronics

olympia electronics GR-470 User manual

olympia electronics

olympia electronics GR-290 User manual

olympia electronics

olympia electronics KLIN-20/ST/ADR User manual

olympia electronics

olympia electronics GR-108/12L/90 User manual

olympia electronics

olympia electronics OLY-500 User manual

olympia electronics

olympia electronics GR-8/leds User manual

olympia electronics

olympia electronics GR-292/M/HL User manual

olympia electronics

olympia electronics WEATHER LIGHT Series User manual

olympia electronics

olympia electronics GR-2100/ST User manual

olympia electronics

olympia electronics BAU LIGHT Series User manual

olympia electronics

olympia electronics GR-270 User manual

olympia electronics

olympia electronics GR-290/M User manual

olympia electronics

olympia electronics GR-8/leds User manual

Popular Lantern manuals by other brands

KYOWA

KYOWA KW-9114 instruction manual

Stahl

Stahl ECOLUX 6610 Series operating instructions

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Operator's manual

PRG

PRG VARI LITE VL5 Service manual

Raytec

Raytec VARIO2 series installation guide

ENSA

ENSA LEDBT18WS2 installation instructions

LUG

LUG OFFICE LB LED N/T Installation instruction

GE Wallighter 250 instructions

Draper

Draper RLEDL19/B instructions

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Assembly & fitting instructions

Panasonic

Panasonic EY3741B57 operating instructions

Clas Ohlson

Clas Ohlson LCC8T instruction manual

Coolon

Coolon WDN-140 manual

Holiday Travel

Holiday Travel 834873 manual

BEGA

BEGA 84 036 Instructions for use

BEGA

BEGA 33 596 Instructions for use

Dale Tiffany

Dale Tiffany GT701162 Assembly instructions

Wagan

Wagan Brite Nite Pop-Up USB Lantern user manual