5 6
Operation Guide （Meeting Booth）For daily care
③Vertical
duct (mag-
net type)
②Wiring
hole
①Wiring cover
Wiring duct
→Power
supply
■ Table wiring
Route the cables using the wiring cover at the center of the table or the wiring hole at both ends
of the back. OA taps can be mounted on the wiring duct and the cable support. Since the vertical
duct is a magnet type, it can be attached and detached according to the seam of the panel.
■ Cable routing diagram
Vertical duct
(magnet type)
Wiring cover
Notch of the
wiring cover
Pin of the cover support
[In case of fewer cables]
Tab
Wiring cover
[In case of many cables]
●Brush with a soft brush or tap the surface
softly and vacuum to remove dust to avoid
damaging the cloth.
●When it gets dirty after extended period
f time, wipe with a well wrung soft cloth
moistened with thin neutral detergent. Wipe
clean with a damp cloth. Be sure to wipe
detergent completely and wipe again with a
dry cloth to dry it.
●When using alkaline electrolyzed water to
remove stains, spray directly on the stain and
brush with a soft brush taking ca re not to
damage the cloth. Then, wipe the moisture and
stain to remove and wait for the cloth to dry.
●Remove stains as quickly as possible.
●
Avoid causing a circular stain, remove not only the
stain but also wipe off thoroughly around the stain.
●If you use a cleaning agent, make sure to
confirm that discoloration or other phenomena
will not occur by applying a small amount of the
agent to an unnoticeable portion in advance.
●Dirt may not be removed depending on the
condition.
●Wipe with a dry, soft cloth.
●When it gets exceptionally dirty, wipe off the
dirt with a well wrung soft cloth moistened
with thin neutral detergent. Be sure to wipe
off detergent completely with a damp cloth
and wipe again with a dry cloth to dry it.
●Remove stains as quickly as possible.
●Dirt may not be removed depending on the
condition.
・
●For daily care, do not use thinner, benzene,
alcohol, lacquers, petroleum, vinegar, boiling
water, polishing powder, wax, etc. Failure
may cause the surface to be damaged.
●Wipe with a well wrung soft cloth moistened.
●When it gets exceptionally dirty, wipe off the
dirt with a well wrung soft cloth moistened
with thin neutral detergent. Be sure to wipe
off detergent completely with a damp cloth
and wipe again with a dry cloth to dry it.
●Remove stains as quickly as possible.
●Dirt may not be removed depending on the
condition.
Back/Seat (upholstery)
Panel (surface materials)
[Polyester or polyester/cotton]
Wall light cover, tabletop bracket, etc.
[Steel]
Tabletop (surface material) [HPL]
●Wipe with a dry, soft cloth.
●Immediately wipe off any water or fingerprints
(sebum). Please note that the aluminum portion
will get oxidized to lose its gloss and deteriorate
the texture if the product is left with water or
fingerprints (sebum) attached.
●Remove any dirt as soon as possible.
●Dirt may not be removed depending on the
condition.
Leg [Metal (aluminum)]
Do not leave the product with moisture remaining
on it. Do not clean the product with organic
solvents such as thinner or benzene, or with a
cloth that contains chemicals. Be aware that once
discoloration or deterioration happens, it cannot
be reverted to its original state.
Please be careful
●Do not rub hard. Failure will cause flashing
to change the viewed color. If dirt cannot
be removed, wipe it of f with a soft
cloth impregnated with alcohol for hand
disinfection.
●Do not use any alkaline or acidic cleaning
agents.
Please be careful
③Vertical duct
Attach the vertical duct with the
notch side facing up. Available on
either the left or right side.
①
Wiring cover
Attach the wiring cover by aligning
the notch of the wiring cover with
the pin of the cover support.
■
Opening and closing the wiring cover
Hold the outer center of the wiring
cover and rotate it while lifting it up.
To close, tilt it outward.
②Wiring hole
The tabletop is equipped with a wiring hole with a cover.
The wiring cover can be rotated to open and close as
shown in the figure. If there are fewer cables to route,
fold the tabs of the wiring cover before use.
