ODSIF Luxury roller blind system User manual

USER GUIDE

FOR MOTORISED ROLLER BLIND

WITH RF REMOTE CONTROL

Model: Luxury roller

blind system

ODSIF

CONTENTS

1. Description of the motorised roller blind system with RF remote control .......... 3

1.1 General features ........................................................................................................3

1.2 Technical data ........................................................................................................... 3

2. Overview of parts...................................................................................................... 4

2.1 Overview of the supplied parts .................................................................................4

3. System installation .................................................................................................... 5

3.1 Measuring and cutting of tube length ....................................................................... 5

3.2 Wall / ceiling installation ..........................................................................................5

3.3 Adding the roller blind fabric.................................................................................... 6

3.4 Adding the bottom list...............................................................................................7

3.5 Inserting the tubular motor and adapter wheel .........................................................7

4. Warnings ....................................................................................................................8

5. Mounting the system................................................................................................. 8

6. Remote control ..........................................................................................................9

6.1 Programming the remote control ..............................................................................9

6.2 Change of direction................................................................................................... 9

6.3 Limit position setting .............................................................................................. 10

6.4 First limit position setting ....................................................................................... 10

6.5 Other limit position settings.................................................................................... 11

6.6 Limit position ﬁne-tuning ....................................................................................... 11

6.7 Delete a limit position............................................................................................. 11

6.8 Dot move and continuous move conversion........................................................... 11

6.9 Add new remote control.......................................................................................... 11

6.10 Delete a single channel memory ........................................................................... 12

6.11 Delete all the memories......................................................................................... 12

7. How to code the ODSIF switch .............................................................................. 13

7.1 How to use the ODSIF switch ................................................................................ 13

8. Trouble shooting...................................................................................................... 13

9. Warranty.................................................................................................................. 14

10. Reservations........................................................................................................... 15

11. Contact information.............................................................................................. 16

DESCRIPTION

Congratulations with your new roller blind system with RF remote control, and which

can also be operated with ODSIF wireless wall switch. Read this manual carefully

prior to installing and using the roller blind sytem to get the most out of your system.

1. Description of the motorised roller blind system with RF remote control

Please note: This product is for indoor use only.

The product is suited for use in residental homes, nursary homes, and business

premises. The system includes motor, tube for the roller blind, adapter wheel, remote

control, bottom list, and wall/ceiling brackets. The model is a slim line design making

the roller blind system ideal for installation where there is limited space.

General features:

a. Slim design Ø38 mm

b. Low noise motor

c. Precise setting of bottom and top positions

d. Up to 6 limit positions

e. Easy to install.

f. Self-checking function stopping the motor if it runs for more than 4-6 minutes,

and if the motor tube temperature exceeds 110°C. In that case, the motor will stop

for 3-10 minutes, and will work again, when cooled down.

1.2 Technical data

a. Input voltage: AC 100-240V

b. Radio frequency: 433,92 MHz

c. RF receiver: Built-in

d. Speed: 30 rpm

e. Maximum width: 250 cm

f. Maximum blind weight: 8 kg

OVERVIEW OF PARTS

Tubular motor Tube

Brackets for tube and motor Adapter wheel Bottom list

Remote control

2.1: Overview of parts

On receipt, check that the above parts are supplied. If any items should be missing,

please contact you supplier prior to installing the product.

Please, note that the colour of the parts e.g. the tubular motor might deviate from the

colour shown in the above picitures.

Screws and rawl plugs

SYSTEM INSTALLATION

3. System installation

Make sure there is enough space for the assembly of the product. The tools required

for the installation of the product are electrical drills with 6-8 mm diameter drill bits

(for concrete wall or ceiling), ﬁbre-measuring tape, cross head screw driver, hand saw

and a pair of scissors.

3.1 Measuring and cutting of tube length

The tube should be cut into proper length. There are two methods for installing the

blind system..

Inner installation: The roller blind is installed insde a window, the tube length should

be 3 cm less than the window width. (See ﬁgure next page).

Outer installation: The roller blind is installed over the actual window covering the

whole surface of the window and its glass; the tube length should be at least 7 cm

longer than the window width (See ﬁgure next page).

Measure the correct length for the tube and cut the tube by handsaw. Please, note that

the edges of the cut tube should be perfectly straight, and clear of any ﬁlings.

3.2 Wall/ceiling installation

The system is designed to be installed on the ceiling or wall. The package comes with

rawl plugs and screws. If applying your unit onto a wall made of plaster boards rather

than brick or solid wall, please use special plaster board’s plugs.

Please note: The brackets should be mounted on the same surface and in straight

line. you must leave a sufﬁcient gap between the wall and the brackets (See ﬁgure

next page).

SYSTEM INSTALLATION Samling af systemet

Inner installation - the tube must be 3 cm shorter than the window width.

Outer installation covering the window.

Bracket Bracket

3.3 Adding the roller blind fabric

Insert the suitable blind into the groove of the aluminium tube until it is ﬂat in posi-

tion. Then turn the tube several times in a clockwise direction ensuring that the tube

turns into the corresponding direction as shown in the below ﬁgure

SYSTEM INSTALLATION

3.4 Adding the bottom list

Place the bottom list at the end of the blind (see below ﬁgure)

3.5 Inserting the tubular motor and adapter wheel

Insert the tubular motor and the adapter wheel into the aluminium tube at each end.

WARNINGS

4. Warnings when handling the motor

Keep away from water. No knocking on the motor. No drilling of hole on motor tube.

Downward cable -

avoid water inﬂow.

Keep away from corrodents. Do not immerse in water.

MOUNTING THE SYSTEM

Spirit level

Ensure horisontal placement

5. Mounting the system

REMOTE CONTROL

Features

• Multiple limit preset, beside end limits, 4 extra middle

limits settings

• Keeps the limits stored, when the power is off

• Self-checking and correcting of brake offset

• Stop on block for security

• Famous quality components to ensure reliable perfor-

mance.

6. Remote control

Press the program

button on the tube

for 1 s.

(use a sharp pin or

similar for this)

Motor jogs

once.

Presss “up” Motor jogs once

and the remote

control has been

programmed.

6.1 Programming

6.2. Change direction

Press “stop”

on the

programmed

remote control

for 5 s.

Motor jogs

once.

Presse “Down” Motor jogs

once and the

direction has

now been

changed.

REMOTE CONTROL

6.3 Limit position setting

a. A maximum of six different positions can be set, the furthest two positions called

the UP and DOWN limit positions and the others called the middle limit position.

b. When the ﬁrst limit position is the UP limit position (see below illustration), all

other limit positions can only be set below this position; the same thing, when the

ﬁrst limit position is the DOWN limit position, all other limit positions can only

be set above this position

c. Every limit position can be ﬁne-tuned or deleted separately. The ﬁrst limit position

can only be ﬁne-tuned, but cannot be deleted separately. It can be deleted when

deleting all memories.

d. The motor stops at the next limit position after accepting once UP/DOWN order.

When it reaches the UP limit position, the UP order cannot be used further; when

it reaches the DOWN limit position, the DOWN order cannot be used further.

e. Press the UP/DOWN button twice on the remote control at the speed of once a

second, the motor will go direct to the UP/DOWN limit without any stop at the

middle limits.

The third limit position

The ﬁrst limit position (Up limit position)

The third limit position

The seceond limit position

The third limit position

All the other limit positions

can be set below the ﬁrst

limit position

6.4 First limit position setting (if there’s no action within 30 s, the motor will exit from limit posi-

tion preparation automatically)

Press the

PROG of the

programmed

remote control

for 1 s.

Motor jogs once

and enters into

limit setting

preparation.

Press “Up”

adjusting the

motor to the

desired position

to set the up

limit position as

ﬁrst limit. Press

“Down” to set

the down limits

as the ﬁrst limit.

Press the rear

PROG for 1 s to

store the limit

position.

Motor jogs

once and the

limit setting is

stored.

Table of contents

Other ODSIF Window Blind manuals

ODSIF

ODSIF de Luxe User manual

Popular Window Blind manuals by other brands

Jysk

Jysk ROGEN manual

SOMFY

SOMFY 1241752 instructions

Rollos

Rollos S-Nanorollo V2 Assembly and operating instruction

Teptron

Teptron Move user manual

Renson

Renson Outdoor Loggia Manual Installation

Project Source

Project Source CDLF2342W quick start guide

Domondo

Domondo PureNight Mounting guide

rollease acmeda

rollease acmeda Easy Spring Air Assembly and installation manual

IKEA

IKEA KADRILJ manual

Hallis Hudson

Hallis Hudson Rolls Super glide instructions

Benthin

Benthin P1614 quick start guide

MV LINE

MV LINE CLARA 015 Installing instructions

Current

Current E-WAND Installation manual and user's guide

weinor

weinor VertiTex ZipR Maintenance Instructions and Directions for use for the end user

Roto

Roto ZAR M R4/R7 Mounting instructions

SOMFY

SOMFY Movelite WT Series instructions

Acmeda

Acmeda RF400 Series instructions

Motura

Motura Pli_353/3 manual