Oasis BA-5429 User manual

These guidelines are recommended for

the proper installation of Oasis products. A

careful review of these procedures (and any

referenced publications) before starting is

important in avoiding an improper assembly

and/or installation.

NOTE: All illustrations in this publication are

typical, and may appear different than the

actual product. Optional items may also be

shown that were not ordered on the product

being installed.

ON WHIRLPOOL EQUIPPED MODELS,

A SEPARATE SET OF INSTRUCTIONS

IS PACKED WITH THE UNIT FOR THE

WHIRLPOOL SYSTEM. READ THEM

BEFORE INSTALLING UNIT!

Special Notes to Installer

uLIFT UNIT ONLY BY THE OUTSIDE

SHELL. DO NOT HANDLE BY SYSTEM

PIPING OR COMPONENTS!

uIt is the sole responsibility of the installer

to determine the requirements necessary for

compliance with all installation code require-

ments!

uAll paperwork packaged with the product

should be saved and presented to the home

owner upon completion of the installation!

uAll published product dimensions are

for reference only. Any critical dimensions

required for installation should be taken

directly from the product being installed!

u Anyindependentmodicationsmadeto

the product (or any options / accessories

supplied) beyond those required for normal

installation can void all warranties! (Refer to

warranties for further information)

INSPECTION GUIDELINES

Carefully check the unit upon receipt. Notify

your supplier immediately if any questions

or problems are encountered during this

process.

DO NOT INSTALL PRODUCT

WITHOUT FIRST ADDRESSING

QUESTIONS WHICH ARISE DURING

THE INSPECTION!

Basic Module Check

lCheck unit drain position for match to

bathroom drain location.

lCheck unit for surface damage.

lCheck unit color for coordination to other

bathroomxtures.

Whirlpool System Check

Assembly and operational instructions are

included in a separate publication for all

whirlpool and air equipped models.

lCheck for proper trim color and system

options.

INSTALLATION SITE FRAMING

Duetoindividualsitevariations,exact

guidelines for every situation cannot be

supplied. The recommended framing and

dimensional requirements shown are for a

typical application and may vary depending

on site requirements.

The dimensions shown are from the sur-

faces where the unit will be attached. This

surface can be bare studding, drywall, or

other suitable underlayment material. It is

importantthattheoorandallframingbe

square and level. Framing should be done

using accepted materials and construction

techniques in accordance with all applicable

codes.

Alcove Style Installation

BA-5429

BA-R-41

BA-R-51

Paradise Isle / TR(G)-S-900

Paradise Isle / TR(G)-IF-900

Geneva / TR(G)-S-200

Geneva / TR(G)-IF-200

Geneva / TR-S-240

Geneva / TR-IF-240

Prestige / TR-S-220

Prestige / TR-IF-220

Geneva / TR-S-270

Geneva / TR-IF-270

Futura / OV(G)-S-310

Futura / OV(G)-IF-310

Futura / OV-S-320

Futura / OV-IF-320

Styllis / BA-6036

Styllis / BA-IF-6036

Styllis / BA-6042

Styllis / BA-IF-6042

Styllis / BA-7236

Styllis / BA-IF-7236

Styllis / BA-6036 / BA-IF-6036

Styllis / BA-6042 (shown) / BA-IF-6042

BA-R-41 R/L

BA-R-51 R/L

Geneva 3260 / TR(G)-S-200 R (shown)

Geneva 3260 / TR(G)-IF-200 R/L

Futura 4272 / OV-S-320 (shown)

Futura 4272 / OV-IF-320

Futura 4260 / OV(G)-S-310 R (shown)

Futura 4260 / OV(G)-IF-310 R/L

Prestige 3466 / TR-S-220 R (shown)

Prestige 3466 / TR-IF-220 R/L

Geneva 3672 / TR-S-270 R (shown)

Geneva 3672 / TR-IF-270 R/L

Geneva 3660 / TR-S-240 R (shown)

Geneva 3660 / TR-IF-240 R/L

Styllis / BA-7236 (shown) / BA-IF-7236

Paradise Isle / TR(G)-S-900 (shown)

Paradise Isle / TR(G)-IF-900

BA--5429

NOTE: A pump access MUST BE

PROVIDED for all whirlpool equipped units

that do not include a removalbe apron

access panel. Additional access may be

required to comply with local codes (illust.

1c & 1e).

NOTE: Preconstructed walls may require

modicationsoradditionalframingmembers

toallowforpipesorttingswhichprotrude

from the unit on whirlpool equipped models.

Installation Procedure

NOTES:

1. ‘Wet-set’ is not required to support the

oorunderanOasisproductduetothe

encapsulated Balsa wood construction.

2. Block base feet on skirted (“S” & “BA”)

models are NOT pre-leveled and will NOT

beincontactwiththeroomoorwhen

placed within the framing and leveled.

With the unit positioned in the alcove, sever-

al details must be checked prior to securing

the unit in place (illust. 2 & 3).

l Conrmtheapronand/orthepre-leveled

unitbaseblocksarerestingushonthe

oor

l Conrmdrainposition.

l Conrmtheunitislevelalongeachside

and across each end.

l Conrmtheunitissquareintheframe-

work.

Oasis units are pre-leveled at the factory,

however, site variations may require shim-

ming to maintain level. If required, place

shimsorllermaterialundertheblock

bases.

NOTE: Any material place under the base

to keep the unit level must be structurally

sound and applied to ensure the unit’s

weight will be equally distributed over the

entire base.

Theuseofshimsorllermaterialmayalso

berequiredbehindthenailingangeat

each framing member to maintain the unit in

the proper position.

With the unit square and level in the alcove,

drilla1/8”holethroughtthenailingange

at each framing member. Secure the unit

inplaceacrossthebackwallrst,followed

BA-R-41 L (illustrated) BA-R-51 L (illustrated)

2” Dia. Drain

2-1/2” Dia. Overflow

C Drain

Clearance

Drain CenterOverflow Center

1-1/4”

60”

8-1/2” 22-3/4”

51-1/2”

14-1/4”

15”

29-1/4”

30-1/2”

2-1/2”

13-1/4”

5-3/4”

Std Unit ABF Unit

A 18-1/2” 20-1/2”

B 17-1/4” 19-1/4”

C 1-1/2” 3-1/2”

D 14-1/2” 16-1/2”

2” Dia. Drain

2-1/2” Dia. Overflow

C Drain

Clearance

Drain CenterOverflow Center

1-1/4”

60”

8-1/2” 22-3/4”

51-1/2”

15-7/8”

32”

33-1/4”

2-3/4”

13”

5-7/8”

16-1/8”

Illustration 1a - Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)

Geneva 3260 / TR(G)-S-200 L

Geneva 3260 / TR(G)-IF-200 L (illustrated)

(S model apron

extendsdown

toroomoor)

50-1/4”

9-3/4”

60”

16”

2” Dia. Drain

32”

16-3/4“

4-1/4”

2-1/2” Dia. Overflow

1“ Drain Clearance

Drain CenterOverflow Center

6-1/2”

1-1/4”

21”

Arm Rest

15-3/4“

Beveled Edge

22-1/4”

33-1/4”

1-1/4”

2”

Geneva 3660 / TR-S-240 L

Geneva 3660 / TR-IF-240 L (illustrated)

(S model apron

extendsdown

toroomoor)

49-5/8”

10-3/8”

60”

17-3/4”

18-1/4”

2” Dia. Drain

36”

16-3/4

4-1/4”

2-1/2” Dia. Overflow

1“ Drain Clearance

Drain CenterOverflow Center

6-1/2“

1-1/4”

21”

Arm Rest

15-3/4“

Beveled Edge

22-1/4

”

37-1/4”

1-1/4”

2”

Std Unit ABF Unit

A 18-1/2” 19-3/4”

B 17-1/4” 18-1/2”

C 16” 17-1/4”

D 1-3/4” 3”

E 13-3/4” 15”

54”

1-5/8”

29”

30-1/4”

1-1/4”

50-3/4”

1-5/8”

14-1/2”

8”

Apron

Style Line

1-1/4”

Splash

1-1/4”

46”

Tub Deck

2” Dia. Drain

2-1/2” Dia. Overflow

Drain Clearance

BA-5429 L

(illustrated)

Std Unit ABF Unit

A 25” 26-3/4”

B 23-3/4” 25-1/2”

C 18-1/4” 20”

D 1-3/4” 3-1/2”

E 16” 17-3/4”

F - -

Std Unit ABF Unit

A 25” 26-3/4”

B 23-3/4” 25-1/2”

C 18-1/4” 20”

D 1-3/4” 3-1/2”

E 16” 17-3/4”

F - -

Std Unit ABF Unit

A 25” 26-3/4”

B 23-3/4” 25-1/2”

C 18-1/4” 20”

D 1-3/4” 3-1/2”

E 16” 17-3/4”

F - -

60-5/8”

11-3/8”

72”

18-1/4”

17-3/4”

2” Dia. Drain

36”

16-3/4“

4-1/4”

2-1/2” Dia. Overflow

1-1/8“ Drain Clearance

Drain CenterOverflow Center

7-1/4“

1-1/4”

21”

Arm Rest

15-5/8“

Beveled Edge

22-1/4”

37-1/4”

1-1/4”

2”

Illustration 1b - End Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)

Prestige / TR-S-220 L

Prestige / TR-IF-220 L (illustrated)

(S model apron

extendsdown

toroomoor)

57-1/4”

8-3/4”

66”

17-1/8”

2” Dia. Drain

34-1/4”

18“

3”

2-1/2” Dia. Overflow

2-1/4“ Drain

Clearance

Drain CenterOverflow Center 6“

22-1/4”

15-3/4“

Leveling Supports

17-1/8”

1-1/4”

21”

Arm Rest

35-1/2”

1-1/4”

1-3/4”

Geneva 3672 / TR-S-270 L

Geneva 3672 / TR-IF-270 L (illustrated)

(S model apron

extendsdown

toroomoor)

Futura 4260 / OV(G)-S-310 L

Futura 4260 / OV(G)-IF-310 L (illustrated)

(S model apron

extendsdown

toroomoor)

2” Dia. Drain

4-1/4”

2-1/2” Dia. Overflow

1-3/8“ Drain Clearance

Drain CenterOverflow Center 6“

Leveling Supports

1-1/4“

Arm Rest

Beveled Edge

15-1/8” 20-3/4”

51-1/2”

60”

9“

42”

43-1/4”

21”

22”

16-1/2” 2“

Styllis / BA-6042

Styllis / BA-IF-6042 (illustrated)

(BA model apron

extendsdown

toroomoor)

Styllis / BA-6036

Styllis / BA-IF-6036 (illustrated)

(BA model apron

extendsdown

toroomoor)

Styllis / BA-7236

Styllis / BA-IF-7236 (illustrated)

(BA model apron

extendsdown

toroomoor)

1-7/8”

36”

37-1/4”

1-1/4”

60”

56-1/4”

1-7/8”

9”

51”

2-1/2” Dia. Overflow

2” Dia. Drain

Head

Rest

Arm Rest

Low Bow Shelf

Head

Rest

18”

5-1/2”

4-1/2”Shelf

Drain Clearance

2”

Pre-Leveled Block Base (IF model)

1-5/8”

42”

43-1/4”

1-1/4”

60”

56-3/4”

1-5/8”

9”

51”

2-1/2”Dia.

Overflow

2” Dia. Drain

Head

Rest

Arm Rest

Low Bow Shelf

Head Rest

21”

5-1/2”

4-1/2”Shelf

Drain Clearance

Pre-Leveled Block Base (IF model)

2”

Pre-Leveled Block Base (IF model)

2”

1-1/4”

5-1/2”

Drain Clearance

1-7/8”

36”

37-1/4”

1-1/4”

72”

68-1/4”

1-7/8”

9”

63”

2-1/2” Dia. Overflow

2” Dia. Drain

Head

Rest

Arm Rest

Low Bow Shelf

Head

Rest

18”

4-1/2”Shelf

Fixture

Blocks

Drain Cut-Out

21" W x 16" H

Pump Access

MANDATORY

on All Whirlpool

Equipped Units

Drain Cut-Out

“

cove

ept

oug

ept

Drain

Center

Drain

Center

ished

Unit Dept

Alcove Length - Unit Width

NOTE: Left End Drain Installation Illustrated.

“

hirl

ool

ump

Access

Illustration 1c - End Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)

2” Dia. Drain

3”

2-1/2” Dia.

Overflow

2“ Drain Clearance Leveling Supports

1-1/4“

21”

41-3/4”

12-3/4”

29”

16”

18”

60”

30”

22-1/4”

43”

1-1/4”

30”

2”

Paradise Isle TR(G)-S-900

Paradise Isle TR(G)-IF-900 (illustrated)

(S model apron

extendsdown

toroomoor)

Futura 4260 / OV-S-320

Futura 4260 / OV-IF-320 (illustrated)

(S model apron

extendsdown

toroomoor)

2” Dia. Drain

4-1/2”

1-3/4“ Drain Clearance Leveling Supports

1-1/4“

Beveled Edge

16-1/2”

14-3/4”

20-3/4”

36”

36“

42”

8-1/4”

33-3/4”

22”

43-1/4”

1-1/4”

72“

2-1/2” Dia. Overflow

2“

Illustration 1d - Front-Center Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)

Model 01 02 03 04 05 06 07 08

BA-5429 54” 30-1/4” 29” 14-1/2” 8” 10-1/2” 12” 10-1/2

BA-R-41 60” 30-1/2” 29-1/4” 14-1/4” 8-1/2” 11” 11-3/4” 13-1/2”

BA-R-51 60” 33-1/4” 32” 15-7/8” 8-1/2” 11” 13-3/8” 13-5/8”

TR(G)-S/IF-200s60” 33-1/4” 32” 16” 9-3/4” 12-1/4” 13-1/2” 13-1/2”

TR(G)-S/IF-240s60” 37-1/4” 36” 17-3/4” 10-3/8” 12-7/8” 15-1/4” 15-3/4”

BA-6036 60” 37-1/4” 36” 18” 9” 11-1/2” 15-1/2” 15-1/2”

BA-6042 60” 43-1/4” 42” 21” 9” 11-1/2” 18-1/2” 18-1/2”

TR-S/IF-220s66” 35-1/2” 34-1/4” 17-1/8” 8-3/4” 11-1/4” 14-5/8” 14-5/8”

TR(G)-S/IF-270s72” 37-1/4” 36” 18-1/4” 11-3/8” 13-7/8” 15-3/4” 15-1/2”

BA-7236 72” 37-1/4” 36” 18” 9” 11-1/2” 15-1/2” 15-1/2”

OV(G)-S/IF-310s 60” 43-1/4” 42” 21” 9” 11-1/2” 18-1/2” 18-1/2”

sWhirlpool equipped ‘S’ model includes a removable apron access panel

bytheangesateachend,thendown

thefrontverticalanges.Use1-1/4”large

headed nails or screws. Continously check

toconrmtheunitremainssquarewithinthe

alcove as it is being secured (illust. 3 & 4).

NOTE: It is advisable to protect the unit sur-

face with a thin plywood or cardboard shield

whilefasteningtheangestotheframing

(illust. 5).

WARNING!

THE INSIDE UNIT SURFACE SHOULD

BE CLEAR OF ALL LOOSE DEBRIS

AND THE SURFACE PROTECTED

BEFORE STEPPING INSIDE.

Removable Apron Panel

Certain aproned models come standard with

a removable apron panel, while most mod-

els include a removable apron panel when a

whirlpool or air system is ordered. Refer to

yourspecicmodelforincludedfeatures.

Oasis models with a removable apron

system incorporate 4-6 adjustable magnet

assemblies for quick and secure panel

removal and reattachment.

The following procedure is recommended

for the careful removal of the apron panel.

1. Grasp the bottom of the apron panel

edge with both hands and pull away from

the unit. This will release the bottom

magnets while the panel top remains at

rest on the upper row of magnets (illust. 7).

2. Pull the panel completely away from the

top magnets and safely store the panel

out of the way to avoid damage.

To reattach the panel:

1. Locate the ‘up’ arrow on the inside of

the panel and rotate it to the correct

position for reassembly.

2. Holdingthepanelatthetopwiththen-

ished side facing you, locate the magnet

alignment edges of the two outside re-

ceiverplateswithyourngers.Anglethe

panel top in toward the unit apron and

attach the receiver plates to the outside

magnets, ensuring the alignment edge is

above the top of the magnet (illust. 8).

3. Once the top of the panel is aligned,

complete the attachment by pushing the

bottom of the panel against the lower

magnet assemblies until they catch.

4. In the event that the reattachment does

not line up, simply remove the panel

(steps 1 & 2 for panel removal) and

repeat the attachment.

Removable Panel Adjustments

Hand adjustments can be made to the

removable apron attachment system should

they become necessary. Simply move the

magnets in or out by turning in either direc-

tion (illust. 9). Reattach the panel to check

foracorrecttandreadjustthemagnetsif

necessary

Nailing

Flange

Wall

Framing

1. Position Tub

in Framed Area. Confirm unit apron is

flush on floor. Whirlpool Access

Confirm Drain Alignment

Nailing Flange

Illustration 2 -

Unit Installation

Procedure

Fixture

Blocks

Front Drain Cut-Out

“

Minim

lcove Depth,

nit Rough-In

epth

Drain

Cut-Out

Drain

Center

Alcove Length - Unit Width

Fini

Unit De

06a

“

Wid

Whi

poo

ump

ccess

Model 01 02 03 04 05a 05b 06a 06b 07 08

TR(G)-S/IF-900*s60” 43” 41-3/4” 29” 30” 30” 27-1/2” 27-1/2” 26-1/2” 10-1/4”

OV-S/IF-320*s72” 43-1/4” 42” 33-3/4” 36” 36” 33-1/2” 33-1/2” 31-1/4” 5-3/4”

*Standard ‘S’ model includes a removable apron access panel

sWhirlpool equipped ‘S’ model includes a removable apron access panel

Illustration 1e - Front-Center Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8”)

Water Supply and Drain Connections

Refer to, and follow, the assembly and

installation instructions provided with the

supply valves and drain system. Carefully

check all connections for leaks.

Finishing Guidelines

Fillerstripsorllermaterialmayberequired

over the framing to ensure the under lay-

mentmountsushoverthenailinganges.

A water resistant under layment is recom-

mended surrounding the unit. Stop the

under layment 1/16 to 1/8-inch from the unit

surface,andllthespacewithacontinuous

bead of water resistant sealant. (Illust. 6)

NOTE: Oasis recommends a high qual-

ity silicone based sealant with a mold and

mildew resistant content.

Use care when fastening the under layment

near the unit surface to avoid damage. Seal

the under layment seams and edges, as

required,andinstallthenishmaterialto

specications.

UNIT SURFACE CARE

WARNING!

NEVER USE ABRASIVE MATERIALS,

OR ABRASIVE CLEANERS

ON THE UNIT SURFACE!

EXTREME CAUTION is urged regarding

the use of any cleaner, acid or solvent

on the unit surface.

READ AND FOLLOW PACKAGE

INSTRUCTIONS FOR ALL

PURCHASED CLEANING PRODUCTS!

Through routine use, the unit surface can

collect residues from soap, bath additives

and natural body oils. Additional deposits

can also collect from minerals or particles

found in the water. After each use, wipe the

excesswaterfromtheunit.Thispractice

will reduce the buildup of deposits and help

maintain the natural unit lustre.

Following a thorough surface cleaning,

anapplicationofqualityautomotivewax

will help reduce major accumulations. The

actualscheduleforcleaningandwaxingwill

depend on unit usage and water quality.

WARNING!

NEVER APPLY WAX

TO THE UNIT FLOOR!

uRoutine Cleaning: Mild, non-abrasive

cleanerspecicallyformulatedforgelcoat

and acrylic surfaces recommended. (Rinse

surface thoroughly)

uHeavy Soap Deposits: Liquid ammonia

household cleaner, applied full strength.

(Rinse surface thoroughly)

uStubborn Stains: Liquid household

cleanerorhydrogenperoxideapplied

full strength. Place a saturated clean rag

directly on stain and let stand several hours.

(Rinse surface thoroughly)

uHard Water Scales: Liquid scale remover

or white vinegar, applied full strength.

(Rinse surface thoroughly)

uMold/Mildew: Liquid mildew remover or

baking soda and water paste. (Apply paste

andallowtozzseveralminutes.)(Rinse

surface thoroughly)

uConstruction Adhesive: Soften adhesive

with a hand held hair dryer and peel off

adhesive. (Caution is advised when using

any electrical device near water.)

For adhesive residue, apply rubbing alcohol

or nail polish remover, full strength. (Rinse

surface thoroughly)

WARNING!

BATH MATS AND OTHER ITEMS

HELD IN PLACE USING SUCTIONS

MUST BE REMOVED FROM THE UNIT

SURFACE AFTER EACH USE.

OVER AN EXTENDED PERIOD

FAILURE TO REMOVE

SUCTION ATTACHED ITEMS WILL

DAMAGE THE UNIT SURFACE.

Illustration 3 -

Unit Installation

Procedure

Nailing

Flange

Wall

Framing

2. Level Tub

in Framed Area.

Whirlpool Access

Confirm unit is square

within the framed area.

Nailing Flange

Confirm the tub is level

along the sides and

across each end.

Illustration 3 -

Unit Installation

Procedure

Nailing Flange

Wall Framing

Drill 1/8 inch hole through

flange at each framing member

Illustration 4 - Securing Unit

Wall

Framing

Secure unit to

framing with

large headed

fasteners.

CAUTION: Protect unit surface

with a shield when fastening.

Nailing Flange

Illustration 5 - Securing Unit

Water Resistant

Underlayment

Waterproof

Sealant

Furring Strip or

Shim Material

Nailing

Flange

Wall Framing

Illustration 6 - Securing Unit

Illustration 9 - Panel Adjustment

Panel

Angled

For

Reattachment

Adjustable

Magnet

Assembly

Top

Receiver

Plate

Magnet

Alignment

Edge

Attach

Top of Panel

First

Illustration 8 -

Panel Attachment

Removable

Panel

Top

Receiver

Plate

Adjustable

Magnet

Assemblies

Bottom

Receiver

Plate

Pull Panel

Bottom

Out To

Remove

Illustration 7 -

Panel Removal

8INST-0760.02 / 060315

Oasis Lifestyle, LLC - 1400 Pidco Drive - Plymouth, Indiana 46563

Oasis Lifestyle Product Assurance Program

Bathing and Shower Unit Structure & Surface Finish Limited Warranty

OasisLifestyleprovidesaperformanceassuranceprogramforunitstructuralintegrityandsurfacenishcoveringave

(5) year period from the date-of-purchase on GELCOAT, and covering a ten (10) year period from the date-of-purchase on

VACUUM FORMED ACRYLIC product, for the original purchaser and subsequent consumer. This Oasis limited warranty pro-

gramaddressesspecicdefectsintheproduct,andtheworkmanshipassociatedwiththemanufactureoftheOasisbathing

andshowerproduct.Thespecicdefectscoveredmustresultinasignicantlyalteredappearanceand/oraffecttheintended

performance standards for the product under normal residential use.

Hydro-Massage Systems (water recirculation & air), Option & Accessories Limited Warranty

Oasis Lifestyle provides a performance assurance program for their hydro-massage systems (herein called ‘system’), and

their options and accessories covering a two (2) year period from the date-of-purchase for the original purchaser and subse-

quentconsumer.ThisOasislimitedwarrantyprogramaddressesspecicdefectsinthesystemcomponents,andthework-

manship associated with the assembly of the systems, along with offered options and accessories installed by Oasis, on an

Oasisunit.Thespecicdefectscoveredmustresultinasignicantlyalteredappearanceand/oraffecttheintendedperfor-

mance standards for the system, the option and/or the accessory.

Duringthecoverageperiod,Oasiswill,atitsdiscretion(followingavericationbyanauthorizedOasisrepresentative),either

provideserviceorsupplyareplacementproductwithoutcharge,butexcludinganycostassociatedwiththetransportation,

removalofand/orreinstallationoftheunit(module).FailuretoallowrequestedinspectionbyanauthorizedOasisrepresenta-

tive,and/orfailuretoprovideadequateaccessibilityforanauthorizedinspection,and/orserviceperformedpriortodocument-

edauthorizationfromOasisLifestyle,LLC.,maydelayservice,and/orpossiblyterminateanywarrantycoverage,andremove

any liability to Oasis Lifestyle, LLC.

This ‘Product Assurance Program’ does not cover service resulting the following:

a) Impropereldinstallationoftheproduct,system,option,accessory,and/orsurroundingstructure

modications,and/orutilityserviceconnectionsbeyondtherecommendationssuppliedbyOasisandwithinthe

scope of applicable codes and ordinances; or

b) Carelessness,damage,abuse,misuse,negligence,impropercare,re,ood,oractsofGod;or

c) Non-conforming use, including any use beyond those intended for the product, system, option and/or

accessory, including failure to follow the Prescribed Care and Maintenance Instructions; or

d) Anyunauthorizedalterationsormodicationstotheproduct,system,option,accessoryand/ortheindividual

parts or components supplied by Oasis.

e) Any surface and/or component staining, discoloration, component failure and/or build-up caused as a result of

water chemistry or water quality at the site.

f) Service resulting from normal use and wear for the product, system, option and/or accessory.

Repairorthesupplyingofreplacementproductand/orcomponents,underthislimitedwarrantyprogram,shallbetheex-

clusive remedy. Oasis Lifestyle, LLC., shall not be liable for any incidental or consequential damages, including damages to

thebuilding/structure,thecontents,theoccupants,orbreachofanyexpressedorimpliedwarranties.OasisLifestyle,LLC.,

doesnotrecognize,norauthorizesanypartytoprovideimpliedorwrittenwarrantiesregardingaproduct,system,optionand/

oraccessoriestnessforaparticularpurpose,normodifythetermsofthelimitedwarrantybeyondthosestated.

Somestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,orallowlimitationsonthedura-

tionofanyimpliedwarranty.Therefore,theaboveexclusionsand/orlimitationsmaynotapply.

THIS WARRANTY PROVIDES SPECIFIC LEGAL RIGHTS, WHICH CAN VARY FROM STATE-TO-STATE.

800.638.8556

HomeInnovation.com

The manufacturer represents that the product to which this

label is affixed (a) duplicates samples independently

tested by Home Innovations Research Labs and certified

to conform to the requirements of HUD UM Bulletin 73a

and the appropriate ANSI Z124 and ICC/ANSI A117.1

standards, and (b) has been manufactured under quality

controls deemed appropriate by the manufacturer and

periodically reviewed by the certifier.

Oasis Lifestyle, LLC

Plymouth, IN

6006

800.638.8556

HomeInnovation.com

The manufacturer represents that the product to which this

label is affixed (a) duplicates samples independently

tested by Home Innovations Research Labs and certified

to conform to the requirements of HUD UM Bulletin 73a

and the appropriate ANSI Z124 and ASME A112.19.7

standards, and (b) has been manufactured under quality

controls deemed appropriate by the manufacturer and

periodically reviewed by the certifier.

Oasis Lifestyle, LLC

Plymouth, IN

6006

This manual suits for next models

Table of contents

Other Oasis Bathtub manuals

Oasis

Oasis Builder Series User manual

Popular Bathtub manuals by other brands

Agua

Agua BARTOLI-66 quick start guide

PAA

PAA PRELUDE owner's manual

BETTE

BETTE SILHOUETTE installation guide

Kohler

Kohler K-820-GC Roughing-In Guide

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW installation instructions

Oliveri

Oliveri Naples installation instructions

Lyons

Lyons Elite ETLxx663219 Series manual

Woodbridge

Woodbridge BJ500 Installation and care guide

Whirlpool

Whirlpool Ariel ARL-702 installation manual

TEIKO

TEIKO EXCELLENT DUO user manual

American Standard

American Standard Colony 5-1/2' x 32" Specification sheet

American Standard

American Standard 3052OD.X0X Installation instructions and owner's manual

Kohler

Kohler K-1111-H2 Roughing-In Guide

agape

agape MARSIGLIA AVAS1075 Assembly instructions

Kohler

Kohler K-1151 Homeowner's guide

Kohler

Kohler K-1158 Roughing-In Guide

Kohler

Kohler K-1244 Homeowner's guide

Kallista

Kallista P50045-G5 Homeowner's guide